Micro Combustor Development Using Hydrogen As Fuel

2018 ◽  
Author(s):  
Ronak Shah ◽  
Digvijay Kulshreshtha ◽  
Nisarg Chaudhari
Keyword(s):  
Flame Front ◽  
Reaction Zone ◽  
Equivalence Ratio ◽  
Cross Sectional ◽  
Turbine Engine ◽  
Micro Gas Turbine ◽  
Constant Area ◽  
Stable Flame ◽  
Temperature Levels ◽  
Micro Combustor

Swiss Roll Combustor of 1 W capacity for micro gas turbine engine is operated with premixed hydrogen air mixture at ultra-lean equivalence ratio. The reaction zone under consideration has volume of 60 mm3. The reactant passage and product passage are coiled around the reaction zone facilitating the recovery of heat loss, by preheating the reactants. The reactants are entered through an increasing cross-sectional area passage from 0.6mm × 5mm inlet to 1.5mm × 5mm outlet, thereby reducing the velocity levels in the reactant passage, facilitating stable combustor operation. The combustor performance parameters, temperature levels, pattern factor and emissions are measured is operated at ultra-lean equivalence ratio of 0.12 to lean equivalence ratio of 0.43, for premixed hydrogen air combustion. The results are compared at similar (not same) equivalence ratios for constant area reactant passage. The visual inspection shows stable flame front in the combustion zone for variable area passage and extended flame front in the constant area passage combustor. However, the combustor performance deteriorates drastically above equivalence ratio of 0.43, leading to hot spots generation on walls.

High Power Density Silicon Combustion Systems for Micro Gas Turbine Engines

2002 ◽  
Author(s):  
C. M. Spadaccini ◽  
J. Lee ◽  
S. Lukachko ◽  
I. A. Waitz ◽  
A. Mehra ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Large Scale ◽  
Experimental Testing ◽  
Deep Reactive Ion Etching ◽  
Turbine Engine ◽  
Micro Gas Turbine ◽  
Micro Scale ◽  
Micro Propulsion ◽  
Micro Combustor ◽  
Power Densities

As part of an effort to develop a micro-scale gas turbine engine for power generation and micro-propulsion applications, this paper presents the design, fabrication, experimental testing, and modeling of the combustion system. Two radial inflow combustor designs were examined; a single-zone arrangement and a primary and dilution-zone configuration. Both combustors were micro-machined from silicon using Deep Reactive Ion Etching (DRIE) and aligned fusion wafer bonding. Hydrogen-air and hydrocarbon-air combustion was stabilized in both devices, each with chamber volumes of 191 mm3. Exit gas temperatures as high as 1800 K and power densities in excess of 1100 MW/m3 were achieved. For the same equivalence ratio and overall efficiency, the dual-zone combustor reached power densities nearly double that of the single-zone design. Because diagnostics in micro-scale devices are often highly intrusive, numerical simulations were used to gain insight into the fluid and combustion physics. Unlike large-scale combustors, the performance of the micro-combustors was found to be more severely limited by heat transfer and chemical kinetics constraints. Important design trades are identified and recommendations for micro-combustor design are presented.

Development of a MEMS-based micro combustor for a micro gas turbine engine

2005 ◽  
Author(s):  
Xue Chuan Shan ◽  
Yu F. Jin ◽  
Zhen F. Wang ◽  
Chee Khuen Wong ◽  
Y. Murakoshi ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbine Engine ◽  
Turbine Engine ◽  
Micro Gas Turbine ◽  
Micro Combustor

Effects of the Equivalence Ratio and Reynolds Number on Turbulence and Flame Front Interactions by Direct Numerical Simulation

2016 ◽  
Vol 30 (8) ◽  
pp. 6727-6737 ◽  
Author(s):  
Cong Xu ◽  
Zhihua Wang ◽  
Wubin Weng ◽  
Kaidi Wan ◽  
Ronald Whiddon ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Reynolds Number ◽  
Direct Numerical Simulation ◽  
Flame Front ◽  
Equivalence Ratio

An Onion Peeling Reconstruction of the Spatial Characteristics of Entropy Waves in a Model Gas Turbine Combustor

2017 ◽  
Author(s):  
Dominik Wassmer ◽  
Felix Pause ◽  
Bruno Schuermans ◽  
Christian Oliver Paschereit ◽  
Jonas P. Moeck
Keyword(s):  
Gas Turbine ◽  
Reaction Zone ◽  
Equivalence Ratio ◽  
Acoustic Noise ◽  
Accurate Determination ◽  
Time Of Flight ◽  
Spark Discharge ◽  
Turbine Stage ◽  
Radial Temperature ◽  
Reconstructed Temperature

Entropy noise affects thermoacoustic stability in lean pre-mixed gas turbine combustion chambers. It is defined as acoustic noise that is emitted at the first turbine stage due to the acceleration of entropy waves that are advected from the reaction zone in the combustor to the turbine inlet. These non-isentropic temperature waves are caused by equivalence ratio fluctuations which are inherently present in a technically premixed combustion system. To experimentally study the generation and transport of entropy waves, an estimation of the spatial distribution of the entropy spots is highly valuable as it allows the accurate determination of the cross-section averaged entropy, which is the relevant quantity for the formation mechanism of entropy noise at the turbine stage. In this work, a time-of-flight based temperature measurement method is applied to a circular combustion test rig equipped with a premixed swirl-stabilized combustor. Downstream of the burner, an electric spark discharge is employed to generate a narrow acoustic pulse which is detected with a circumferentially arranged microphone array. The measured time of flight of the acoustic signal corresponds to the line-integrated inverse of the speed of sound between the acoustic source and each microphone. By modulating a share of the injected gaseous fuel, equivalence ratio fluctuations are generated upstream of the reaction zone and consequently entropy spots are advected through the axial measurement plane. The spark discharge is triggered at distinct phase angles of the entropy oscillation, thus allowing a time resolved-analysis of the thermo-acoustic phenomenon. Estimating the spatial temperature distribution from the measured line integrated inverse speed of sounds requires tomographic reconstruction. A Tikhonov regularized Onion Peeling is employed to deduce radial temperature profiles. To increase the number of independent data, the spark location is radially traversed, which enhances the resolution of the reconstructed temperature field. A phantom study is conducted, which allows the assessment of the capabilities of the reconstruction algorithm. By means of the reconstructed radial entropy field, spatially resolved entropy waves are measured and their amplitudes and phases are extracted. The characteristics of the entropy waves measured in this way correspond well to former studies.

Flame Characteristics and Turbulent Flame Speeds of Turbulent, High-Pressure, Lean Premixed Methane/Air Flames

2005 ◽  
Author(s):  
P. Griebel ◽  
R. Bombach ◽  
A. Inauen ◽  
R. Scha¨ren ◽  
S. Schenker ◽  
...  
Keyword(s):  
Flame Front ◽  
Gas Turbines ◽  
Equivalence Ratio ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Operating Conditions ◽  
Turbulent Flame Speed ◽  
Front Position ◽  
Preheating Temperature ◽  
Lean Premixed

The present experimental study focuses on flame characteristics and turbulent flame speeds of lean premixed flames typical for stationary gas turbines. Measurements were performed in a generic combustor at a preheating temperature of 673 K, pressures up to 14.4 bars (absolute), a bulk velocity of 40 m/s, and an equivalence ratio in the range of 0.43–0.56. Turbulence intensities and integral length scales were measured in an isothermal flow field with Particle Image Velocimetry (PIV). The turbulence intensity (u′) and the integral length scale (LT) at the combustor inlet were varied using turbulence grids with different blockage ratios and different hole diameters. The position, shape, and fluctuation of the flame front were characterized by a statistical analysis of Planar Laser Induced Fluorescence images of the OH radical (OH-PLIF). Turbulent flame speeds were calculated and their dependence on operating conditions (p, φ) and turbulence quantities (u′, LT) are discussed and compared to correlations from literature. No influence of pressure on the most probable flame front position or on the turbulent flame speed was observed. As expected, the equivalence ratio had a strong influence on the most probable flame front position, the spatial flame front fluctuation, and the turbulent flame speed. Decreasing the equivalence ratio results in a shift of the flame front position farther downstream due to the lower fuel concentration and the lower adiabatic flame temperature and subsequently lower turbulent flame speed. Flames operated at leaner equivalence ratios show a broader spatial fluctuation as the lean blow-out limit is approached and therefore are more susceptible to flow disturbances. In addition, because of a lower turbulent flame speed these flames stabilize farther downstream in a region with higher velocity fluctuations. This increases the fluctuation of the flame front. Flames with higher turbulence quantities (u′, LT) in the vicinity of the combustor inlet exhibited a shorter length and a higher calculated flame speed. An enhanced turbulent heat and mass transport from the recirculation zone to the flame root location due to an intensified mixing which might increase the preheating temperature or the radical concentration is believed to be the reason for that.

scholarly journals Investigation of Micro Gas Turbine Systems for High Speed Long Loiter Tactical Unmanned Air Systems

Aerospace ◽  
2019 ◽  
Vol 6 (5) ◽  
pp. 55 ◽  
Author(s):  
James Large ◽  
Apostolos Pesyridis
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
High Speed ◽  
Engine Performance ◽  
Operating Conditions ◽  
Turbine Engine ◽  
Micro Gas Turbine ◽  
Fan Speed ◽  
Relative Design ◽  
Design Simplicity

In this study, the on-going research into the improvement of micro-gas turbine propulsion system performance and the suitability for its application as propulsion systems for small tactical UAVs (<600 kg) is investigated. The study is focused around the concept of converting existing micro turbojet engines into turbofans with the use of a continuously variable gearbox, thus maintaining a single spool configuration and relative design simplicity. This is an effort to reduce the initial engine development cost, whilst improving the propulsive performance. The BMT 120 KS micro turbojet engine is selected for the performance evaluation of the conversion process using the gas turbine performance software GasTurb13. The preliminary design of a matched low-pressure compressor (LPC) for the proposed engine is then performed using meanline calculation methods. According to the analysis that is carried out, an improvement in the converted micro gas turbine engine performance, in terms of thrust and specific fuel consumption is achieved. Furthermore, with the introduction of a CVT gearbox, the fan speed operation may be adjusted independently of the core, allowing an increased thrust generation or better fuel consumption. This therefore enables a wider gamut of operating conditions and enhances the performance and scope of the tactical UAV.

Sign in / Sign up

Export Citation Format

Share Document