scholarly journals Investigation on a low-cost single wavelength converged wired-60 GHz wireless OFDM-based system employing a photonic patch antenna

2013 ◽  
Author(s):  
Spiros Mikroulis ◽  
Ivan Aldaya ◽  
Ioannis Petropoulos ◽  
Elias Giacoumidis ◽  
Kostantinos Voudouris ◽  
...  
Keyword(s):  
Patch Antenna ◽  
Low Cost ◽  
60 Ghz

A Low-Cost 60-GHz Switched-Beam Patch Antenna Array With Butler Matrix Network

2008 ◽  
Vol 7 ◽  
pp. 432-435 ◽  
Author(s):  
Chao-Hsiung Tseng ◽  
Chih-Jung Chen ◽  
Tah-Hsiung Chu
Keyword(s):  
Antenna Array ◽  
Patch Antenna ◽  
Low Cost ◽  
60 Ghz ◽  
Butler Matrix

scholarly journals On the application of the EM-imaging for chipless RFID tags

2015 ◽  
Vol 2 (2) ◽  
pp. 86-96 ◽  
Author(s):  
M. Zomorrodi ◽  
N.C. Karmakar
Keyword(s):  
Radio Frequency Identification ◽  
Low Cost ◽  
60 Ghz ◽  
Rfid Tag ◽  
High Data ◽  
Data Encoding ◽  
Bending Effect ◽  
Chipless Rfid ◽  
Frequency Identification ◽  
Cost Item

The electromagnetic (EM) imaging technique at mm-band 60 GHz is proposed for data encoding purpose in the chipless Radio Frequency Identification (RFID) systems. The fully printable chipless RFID tag comprises tiny conductive EM polarizers to create high cross-polar radar cross-section. Synthetic aperture radar approach is applied for formation of the tag's EM-image and revealing the tag's content. The achieved high data encoding capacity of 2 bits/cm2in this technique based on a fully printable tag is very convincing for many applications. The system immunity to multipath interference, bending effect, and printing inaccuracy suggests huge potentials for low-cost item tagging. Tags are also readable through a tick paper envelop; hence secure identification is provided by the proposed technique.

scholarly journals A Novel Electrically Small Ground-Penetrating Radar Patch Antenna with a Parasitic Ring for Respiration Detection

Sensors ◽  
2021 ◽  
Vol 21 (6) ◽  
pp. 1930
Author(s):  
Di Shi ◽  
Taimur Aftab ◽  
Gunnar Gidion ◽  
Fatma Sayed ◽  
Leonhard M. Reindl
Keyword(s):  
Ground Penetrating Radar ◽  
Patch Antenna ◽  
Low Cost ◽  
Substrate Material ◽  
Geometric Parameters ◽  
Gas Explosions ◽  
Aerial Vehicle ◽  
Electromagnetic Characteristics ◽  
Ground Penetrating ◽  
Quick Search

An electrically small patch antenna with a low-cost high-permittivity ceramic substrate material for use in a ground-penetrating radar is proposed in this work. The antenna is based on a commercial ceramic 915 MHz patch antenna with a size of 25 × 25 × 4 mm3 and a weight of 12.9 g. The influences of the main geometric parameters on the antenna’s electromagnetic characteristics were comprehensively studied. Three bandwidth improvement techniques were sequentially applied to optimize the antenna: tuning the key geometric parameters, adding cuts on the edges, and adding parasitic radiators. The designed antenna operates at around 1.3 GHz and has more than 40 MHz continuous −3 dB bandwidth. In comparison to the original antenna, the −3 and −6 dB fractional bandwidth is improved by 1.8 times and 4 times, respectively. Two antennas of the proposed design together with a customized radar were installed on an unmanned aerial vehicle (UAV) for a quick search for survivors after earthquakes or gas explosions without exposing the rescue staff to the uncertain dangers of moving on the debris.

scholarly journals Single-Layer Line-Fed Broadband Microstrip Patch Antenna on Thin Substrates

Electronics ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 37
Author(s):  
Roberto Vincenti Gatti ◽  
Riccardo Rossi ◽  
Marco Dionigi
Keyword(s):  
Patch Antenna ◽  
State Of The Art ◽  
Low Cost ◽  
Single Layer ◽  
Microstrip Antennas ◽  
Microstrip Patch Antenna ◽  
Layer Line ◽  
Limited Bandwidth ◽  
Microstrip Patch ◽  
Effective Design

In this work, the issue of limited bandwidth typical of microstrip antennas realized on a single thin substrate is addressed. A simple yet effective design approach is proposed based on the combination of traditional single-resonance patch geometries. Two novel shaped microstrip patch antenna elements with an inset feed are presented. Despite being printed on a single-layer substrate with reduced thickness, both radiators are characterized by a broadband behavior. The antennas are prototyped with a low-cost and fast manufacturing process, and measured results validate the simulations. State-of-the-art performance is obtained when compared to the existing literature, with measured fractional bandwidths of 3.71% and 6.12% around 10 GHz on a 0.508-mm-thick Teflon-based substrate. The small feeding line width could be an appealing feature whenever such radiating elements are to be used in array configurations.

Sign in / Sign up

Export Citation Format

Share Document