scholarly journals Reflection of simple wave at vapor-liquid interface accompanied with phase change

2018 ◽  
Author(s):  
Takeru Yano
Keyword(s):  
Phase Change ◽  
Simple Wave ◽  
Liquid Interface ◽  
Vapor Liquid

Electronic Effects on the Surface Potential at the Vapor−Liquid Interface of Water

2008 ◽  
Vol 130 (49) ◽  
pp. 16556-16561 ◽  
Author(s):  
Shawn M. Kathmann ◽  
I-Feng William Kuo ◽  
Christopher J. Mundy
Keyword(s):  
Surface Potential ◽  
Liquid Interface ◽  
Electronic Effects ◽  
Vapor Liquid

scholarly journals Free-standing polypyrrole/polyaniline composite film fabricated by interfacial polymerization at the vapor/liquid interface for enhanced hexavalent chromium adsorption

RSC Advances ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 5445-5452 ◽  
Author(s):  
Vu Dinh Thao ◽  
Bach Long Giang ◽  
Tran Viet Thu
Keyword(s):  
Composite Film ◽  
Hexavalent Chromium ◽  
Interfacial Polymerization ◽  
Liquid Interface ◽  
Free Standing ◽  
Chromium Adsorption ◽  
Vapor Liquid

Free-standing polypyrrole/polyaniline composite film fabricated by interfacial polymerization at vapor/liquid interface.

Infrared Thermal Image on Vapor-Liquid Interface in Capillary Microgrooves Heat Sink

2009 ◽  
Author(s):  
Tao Wang ◽  
Xuegong Hu ◽  
Dawei Tang ◽  
Chaohong Guo
Keyword(s):  
Temperature Distribution ◽  
Heat Sink ◽  
Solid Wall ◽  
Thermal Image ◽  
Liquid Interface ◽  
Liquid Interfaces ◽  
Average Temperature ◽  
Solid Walls ◽  
Working Liquid ◽  
Vapor Liquid

An infrared thermoviewer is utilized to measure the temperature distribution on solid walls and vapor-liquid interfaces of the rectangular capillary microgrooves heat sink, which is made of borosilicate glass. The infrared thermal image clearly shows that the solid wall temperature of microgroove top is lower than the average temperature of vapor-liquid interface. The results indicate that heat source position has a significant influence on the microgrooves surface temperature distribution, besides working liquid, tilt angle (the angle between microgroove surface and gravity direction) and heat flux.

Experiments on Flow Boiling Heat Transfer of Ammonia/Water Mixture Inside an Internally Spirally Grooved Horizontal Tube

2010 ◽  
Author(s):  
Satoru Momoki ◽  
Hirofumi Arima ◽  
Hiroyuki Asou ◽  
Odgerel Jambal ◽  
Tomohiko Yamaguchi ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Flow Boiling ◽  
Steel Tube ◽  
Liquid Interface ◽  
Bulk Temperature ◽  
Diffusion Resistance ◽  
Water Mixture ◽  
Transfer Coefficients ◽  
Experimental Conditions ◽  
Vapor Liquid

Experiments were performed on the flow boiling of the zeotropic mixture of water-ammonia inside an internally spirally grooved horizontal steel tube with a 12mm average inner diameter. The experimental conditions were the mass fraction of ammonia: 0.95, 1.0 kg/kg, the mass velocity: 40 to 80 kg/(m2s), the heat flux: 0 to 20 kW/m2 and the pressure: 0.7 MPa. The measured heat transfer coefficient reached its maximum as the quality approached about 0.6 but decreased abruptly as the quality increased. This sharp decrease as the quality increased beyond 0.6 may have been caused by mass diffusion resistance that increased the temperature locally at the vapor-liquid interface. The temperature increase at the vapor-liquid interface is discussed by analyzing the phase equilibrium characteristics and is explained in terms of the relationship between the bulk temperature and vapor quality. The heat transfer coefficients are also compared with those for pure ammonia.

Sign in / Sign up

Export Citation Format

Share Document