Behavior of the Complex REM-Containing Modifier in Melting of Fe–Al Alloys in an Open Induction Furnace

A new modified austenitic stainless steel has been developed through partial replacement of nickel by nitrogen. Nitrogen stainless steel was produced in 10 kg induction furnace under nitrogen pressure, while reference one, AISI 316 steel grade, was produced in open-induction furnace. Both were cast and hot forged, and the total nitrogen was determined. Furthermore, the produced forged steels were subjected to solution treatment at different temperatures. The microstructure of produced stainless steels was observed. The X-ray diffractmeter and Mossbauer effect spectroscopy were used to follow the phase change in reference and modified steels after different heat treatment temperatures. The influence of grain-size, soluble, and insoluble nitrogen on tensile strength and hardness was investigated. The major phase in the modified steel has a fcc structure similar to the reference one, but with finer grains and more expanded lattice. The yield strength and hardness of the nitrogen-modified stainless steel are higher than the reference steel. On the other hand, the increase of nitrogen content deteriorates the steel ductility.

Download Full-text

Influence of Vanadium and Cast Temperature on Nitrogen Solubility of Stainless Steel

Journal of Metallurgy ◽

10.1155/2014/528121 ◽

2014 ◽

Vol 2014 ◽

pp. 1-6 ◽

Cited By ~ 2

Author(s):

Saeed Ghali

Keyword(s):

Stainless Steel ◽

Chemical Composition ◽

Stainless Steels ◽

Induction Furnace ◽

Nitrogen Solubility ◽

Vanadium Content ◽

Steel Grades ◽

Cr 5.17 ◽

Open Induction ◽

Nitrogen Contents

Three stainless steel grades with different vanadium content were produced in open induction furnace. The base chemical composition of investigated stainless steel has contained 18.48–18.75% Cr, 5.17–5.62% Mn, 2.47–2.58% Mo, and 6.39–6.64% Ni. The vanadium contents of the three stainless steel grades were 0.009%, 0.112%, and 0.189%. The proposed stainless steels were casted at temperatures 1753 K and 1833 K. The nitrogen contents were determined for the produced steel grades at every cast temperature. The determined nitrogen contents were compared with those calculated from the developed equation of Grigorenko and Pomarin. The influence of cast temperature and vanadium content on nitrogen solubility was investigated. Interpretation between experimental and calculated nitrogen content was carried out. Increasing vanadium content and decreasing cast temperature were found to have positive significant effect on the nitrogen solubility. There were great deviations between experimental results and those calculated by Grigorenko and Pomarin equation.

Download Full-text

Observation of faint contrast at planar faults in alloys

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100108842 ◽

1978 ◽

Vol 36 (1) ◽

pp. 340-341

Author(s):

K. Kuroda ◽

Y. Tomokiyo ◽

T. Kumano ◽

T. Eguchi

Keyword(s):

Reciprocal Lattice ◽

Beam Theory ◽

Al Alloys ◽

Small Displacement ◽

Electron Microscopic ◽

Lattice Vector ◽

Fringe Contrast ◽

Planar Fault ◽

Lattice Displacement ◽

The Many

The contrast in electron microscopic images of planar faults in a crystal is characterized by a phase factor , where is the reciprocal lattice vector of the operating reflection, and the lattice displacement due to the fault under consideration. Within the two-beam theory a planar fault with an integer value of is invisible, but a detectable contrast is expected when the many-beam dynamical effect is not negligibly small. A weak fringe contrast is also expected when differs slightly from an integer owing to an additional small displacement of the lattice across the fault. These faint contrasts are termed as many-beam contrasts in the former case, and as ε fringe contrasts in the latter. In the present work stacking faults in Cu-Al alloys and antiphase boundaries (APB) in CuZn, FeCo and Fe-Al alloys were observed under such conditions as mentioned above, and the results were compared with the image profiles of the faults calculated in the systematic ten-beam approximation.

Download Full-text

Microstructure of an extruded rapidly solidified Al-8Fe-2Mo alloy

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100144218 ◽

1986 ◽

Vol 44 ◽

pp. 548-549

Author(s):

W. T. Donlon ◽

J. E. Allison ◽

S. Shinozaki

Keyword(s):

Electron Microscopy ◽

Automotive Industry ◽

Fuel Economy ◽

High Strength ◽

Al Alloys ◽

Light Weight ◽

Thin Sections ◽

Strength And Durability ◽

Rapidly Solidified ◽

Whitney Aircraft

Light weight materials which possess high strength and durability are being utilized by the automotive industry to increase fuel economy. Rapidly solidified (RS) Al alloys are currently being extensively studied for this purpose. In this investigation the microstructure of an extruded Al-8Fe-2Mo alloy, produced by Pratt & Whitney Aircraft, Goverment Products Div. was examined in a JE0L 2000FX AEM. Both electropolished thin sections, and extraction replicas were examined to characterize this material. The consolidation procedure for producing this material included a 9:1 extrusion at 340°C followed by a 16:1 extrusion at 400°C, utilizing RS powders which have also been characterized utilizing electron microscopy.

Download Full-text