Making the wire frame solid

Author(s):  
Donald Robbins
Keyword(s):  
Author(s):  
S. Gupta ◽  
A. Shirkhodaie ◽  
A. H. Soni

Abstract This paper presents an algorithm to generate surface models of 3D objects from their wire-frame models. The algorithm firstly, obtains information about edges of the object from the wire-frame model of the object and uses this edge information to generate the pairs. A pair of an object is a combination of two non-collinear edges which have a common vertex. The algorithm then determines the unique plane passing through each pair and groups the coplanar pairs together. Then it sorts each of the groups of coplanar pairs to form one or more loops of edges. Finally for each group of coplanar pairs, all the loops are combined, using a few rules, to form faces of the object. Hence a surface model of the object is generated.


Neurosurgery ◽  
2010 ◽  
Vol 67 (3) ◽  
pp. 818-823 ◽  
Author(s):  
Anand V. Germanwala ◽  
Quoc-Anh Thai ◽  
Gustavo Pradilla ◽  
Rafael J. Tamargo

Abstract BACKGROUND Precise surgical localization of small arteriovenous malformations (AVMs), arteriovenous fistulae (AVFs), and aneurysms located in the distal portions of the intracranial arteries can be difficult OBJECTIVE We describe a simple and accurate intraoperative angiographic localization technique for small AVMs, AVFs, and distal aneurysms. METHODS All patients had routine preoperative diagnostic imaging and evaluations, including catheter angiography. Once anesthetized, the patients were prepared for intraoperative angiography following cannulation of the femoral artery. Craniometric landmarks were utilized to approximately localize the lesion. A wire in the shape of a square was placed over the proposed craniotomy site and an angiogram was performed. With use of real-time angiography, the wire localizer was manipulated until the small vascular lesion was visualized entirely within the wire frame, thus defining the extent of the required craniotomy and the surgical trajectory. RESULTS The wire localizer was used to target small vascular lesions in 9 cases of AVMs, 4 cases of distal middle cerebral artery aneurysms, and 1 case of a diploic AVF. In all 14 cases, the lesion was accurately localized intraoperatively without further image-guided techniques, and there was no change in the craniotomy. There were no intraoperative complications, and all patients had uneventful recoveries. CONCLUSION Intraoperative angiography with a simple wire localizer can effectively and accurately aid in the planning of surgery for a range of small and distal vascular lesions with virtually no added cost, minimal setup time, and limited potential for technical errors.


1990 ◽  
Vol 23 (9) ◽  
pp. 999-1010 ◽  
Author(s):  
Jayanta Mukherjee ◽  
P.P. Das ◽  
B.N. Chatterji

2022 ◽  
Vol 2160 (1) ◽  
pp. 012070
Author(s):  
Guiyun Huang ◽  
Yong Li ◽  
Jian Cui

Abstract The article elaborates the significance of the cutting feature in different ways, the shape structure and modeling approach of cutting feature are analyzed through examples. The modeling method is summarized: 1) According to the projection relation, the wire frame is separated. According to the projection of view, the positional relation of each plane is analysed, the corresponding plane of the wireframe is determined the shape of the cut is clarified. This is the key to deciding whether the modeling can be completed successfully. 2) By imagining the shape, the position and order are determined. By line-plane analysis and dimensioning, the cutting position and order of the surface are determined, and the shape and structure after cutting are clarified. This is an important basis for rapid modelling. 3)Thinking overall. Repeatedly compare the shape with the views, and comprehensively check to ensure that the feature position of the shape is clear, the shape is accurate, and the structure is complete.


Author(s):  
Amitesh Mishra ◽  
Anupam Saxena

In this paper is proposed a method to reconstruct a solid from given two or three orthographic views along with any number of primary auxiliary views based on the combination of wireframe and volumetric approaches. None of the existing works in automatic reconstruction of solids from two dimensional orthographic views have addressed auxiliary views in detail. Polyhedral approximation of cylindrical, conical, toroidal and spherical surfaces is considered. The algorithm presented, entails the construction of the basic wire-frame from given standard views using the wire-frame approach. The projections in the auxiliary views on the basic orthographic views are swept along the projection lines to form the primitives. These primitives are glued to the basic wire-frame to construct the final solid. Numerous examples are presented in this paper to demonstrate the versatility of the proposed method which can handle partial standard and auxiliary views as well.


2012 ◽  
Vol 16 (1) ◽  
pp. 127-139 ◽  
Author(s):  
Almar Klein ◽  
J. Adam van der Vliet ◽  
Luuk J. Oostveen ◽  
Yvonne Hoogeveen ◽  
Leo J. Schultze Kool ◽  
...  

Author(s):  
A. W. West

The influence of the filament microstructure on the critical current density values, Jc, of Nb-Ti multifilamentary superconducting composites has been well documented. However the development of these microstructures during composite processing is still under investigation.During manufacture, the multifilamentary composite is given several heat treatments interspersed in the wire-drawing schedule. Typically, these heat treatments are for 5 to 80 hours at temperatures between 523 and 573K. A short heat treatment of approximately 3 hours at 573K is usually given to the wire at final size. Originally this heat treatment was given to soften the copper matrix, but recent work has shown that it can markedly change both the Jc value and microstructure of the composite.


Sign in / Sign up

Export Citation Format

Share Document