scholarly journals On the Failure and Fracture of Polymer Foam Containing Discontinuities

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Addis Kidane
Keyword(s):  
Fracture Behavior ◽  
Loading Rate ◽  
Defect Size ◽  
Tensile Failure ◽  
Uniaxial Tensile ◽  
Strengthening Effect ◽  
Polymer Foam ◽  
Dog Bone ◽  
Fracture Study ◽  
Series Of Experiments

An experimental study is performed to investigate the tensile failure and fracture behavior of polymer foam containing discontinuities. PVC corecell foam, series A800 and A1200 is used for the investigation. Unnotched dog-bone specimen and specimens with center hole and edge cracks are tested under uniaxial tensile loading. Series of experiments are conducted at different defect size to width ratios, and the effect of the defect size on the net-section tensile strength of the foam is investigated. A fracture study is also conducted, and the effect of density and loading rate on the fracture behavior of foam is investigated. A minimal notch-strengthening effect is observed in specimens with center hole, and a notch-weakening effect is observed in specimen with edge notches. Furthermore, the fracture toughness increases with the increase in the foam density and decreases with the increase in loading rate.

Quasi-Static Tensile Properties and Damage Mechanism of Three-Dimensional Angle-Interlock Woven Composites

2012 ◽  
Vol 182-183 ◽  
pp. 148-152
Author(s):  
Kun Luan ◽  
Fa Zhang ◽  
Li Wei Wu
Keyword(s):  
Tensile Properties ◽  
Composite Structures ◽  
Three Dimensional ◽  
Test System ◽  
Tensile Failure ◽  
Woven Composites ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Absorption Mechanism ◽  
Dog Bone

The uniaxial tensile properties of three-dimensional angle-interlock woven composites (3DAWCs) under quasi-static loading were investigated in this paper. The samples were manufactured into dog-bone shape and tested on Material Test System 810.23. The strain-stress curves in warp direction indicating the Young’s moduli, maximum stress and maximum strain are achieved from the uniaxial tensile test. The effects of microstructure and damage morphology of 3DAWC under quasi-static tension are discussed. Furthermore, we will focus on the energy absorption mechanism from the view of tensile failure mode. The material parameters of 3DAWC in warp direction can be evaluated for developing quantitative approach to design polymer matrix composite structures.

Loading rate effect on fracture behavior of fiber reinforced high strength concrete using a semi-circular bending test

2020 ◽  
Vol 240 ◽  
pp. 117681
Author(s):  
Mehran Aziminezhad ◽  
Sahand Mardi ◽  
Pouria Hajikarimi ◽  
Fereidoon Moghadas Nejad ◽  
Amir H. Gandomi
Keyword(s):  
High Strength Concrete ◽  
Fracture Behavior ◽  
Loading Rate ◽  
High Strength ◽  
Rate Effect ◽  
Bending Test ◽  
Fiber Reinforced ◽  
Strength Concrete

Impact tensile behavior and frequency response of 3D braided composites

2011 ◽  
Vol 82 (3) ◽  
pp. 280-287 ◽  
Author(s):  
Xuehui Gan ◽  
Jianhua Yan ◽  
Bohong Gu ◽  
Baozhong Sun
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Tensile Properties ◽  
High Strain ◽  
Tensile Modulus ◽  
Tensile Failure ◽  
Uniaxial Tensile ◽  
Strain Rates ◽  
Braided Composites ◽  
3D Braided Composites

The uniaxial tensile properties of 4-step 3D braided E-glass/epoxy composites under quasi-static and high-strain rate loadings have been investigated to evaluate the tensile failure mode at different strain rates. The uniaxial tensile properties at high strain rates from 800/s to 2100/s were tested using the split Hopkinson tension bar (SHTB) technique. The tensile properties at quasi-static strain rate were also tested and compared with those in high strain rates. Z-transform theory is applied to 3D braided composites to characterize the system dynamic behaviors in frequency domain. The frequency responses and the stability of 3D braided composites under quasi-static and high-strain rate compression have been analyzed and discussed in the Z-transform domain. The results indicate that the stress-strain curves are rate sensitive, and tensile modulus, maximum tensile stress and corresponding tensile strain are also sensitive to the strain rate. The tensile modulus, maximum tensile stress of the 3D braided composites are linearly increased with the strain rate. With increasing of the strain rate (from 0.001/s to 2100/s), the tensile failure of the 3D braided composite specimens has a tendency of transition from ductile failure to brittle failure. The magnitude response and phase response is very different in quasi-static loading with that in high-strain rate loading. The 3D braided composite system is more stable at high strain rate than quasi-static loading.

scholarly journals Determination of Forming Limits Based on Finite Element Simulations

2021 ◽  
Author(s):  
Fuhui Shen ◽  
Kai Chen ◽  
Junhe Lian ◽  
Sebastian Münstermann
Keyword(s):  
Finite Element ◽  
Damage Mechanics ◽  
Tensile Tests ◽  
Finite Element Simulations ◽  
Experimental Results ◽  
Uniaxial Tensile ◽  
Anisotropic Plasticity ◽  
Forming Limits ◽  
Dog Bone ◽  
Spatio Temporal

Two categories of experiments have been performed to obtain the experimental forming limits of a ferritic stainless steel from uniaxial to equibiaxial tension, including Nakajima tests and tensile tests of flat specimens with different geometries of the central hole as well as the notched dog bone. The plasticity behavior of the investigated material is described using an evolving non-associated anisotropic plasticity model, which is calibrated based on experimental results of uniaxial tensile tests along different loading directions. A damage mechanics model is calibrated and validated based on the global force and displacement response of tensile tests. Finite element simulations of the Nakajima tests and the tensile tests of various geometries have been performed using the anisotropic material model. A novel spatio-temporal method is developed to evaluate the forming limits under different stress states by quantitatively characterizing the plastic strain distribution on the specimen surface. The forming limits have been independently determined from finite element simulation results of tensile specimens and Nakajima specimens using the spatio-temporal evaluation method. The forming limits obtained from numerical simulations of these two types of experiments are in good agreement with experimental results.

FRACTURE BEHAVIOR OF Zr-BASED BULK METALLIC GLASS UNDER IMPACT LOADING

2006 ◽  
Vol 20 (25n27) ◽  
pp. 4359-4364 ◽  
Author(s):  
HYUNG-SEOP SHIN ◽  
KI-HYUN KIM ◽  
SANG-YEOB OH
Keyword(s):  
Fracture Toughness ◽  
Crack Initiation ◽  
Fracture Energy ◽  
Impact Loading ◽  
Static Loading ◽  
Fracture Behavior ◽  
Loading Rate ◽  
Shear Bands ◽  
Maximum Load ◽  
Cu Alloy

The fracture behavior of a Zr -based bulk amorphous metal under impact loading using subsize V-shaped Charpy specimens was investigated. Influences of loading rate on the fracture behavior of amorphous Zr - Al - Ni - Cu alloy were examined. As a result, the maximum load and absorbed fracture energy under impact loading were lower than those under quasi-static loading. A large part of the absorbed fracture energy in the Zr -based BMG was consumed in the process for crack initiation and not for crack propagation. In addition, fractographic characteristics of BMGs, especially the initiation and development of shear bands at the notch tip were investigated. Fractured surfaces under impact loading are smoother than those under quasi-static loading. The absorbed fracture energy appeared differently depending on the appearance of the shear bands developed. It can be found that the fracture energy and fracture toughness of Zr -based BMG are closely related with the extent of shear bands developed during fracture.

Sign in / Sign up

Export Citation Format

Share Document