scholarly journals Researches on Crack Propagation of the Two Filled Noncoalescent Coplanar Flaws under the High Strain Rate Loading by means of AUTODYN-Based Simulation

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Guangming Zhao ◽  
Chongyan Liu ◽  
Cheng Pan ◽  
Xiangrui Meng
Keyword(s):  
Crack Initiation ◽  
Crack Propagation ◽  
Dynamic Loading ◽  
High Strain ◽  
Position Angle ◽  
Position Sequence ◽  
Simulation Results ◽  
Initiation Sequence ◽  
Strain Rate Loading ◽  
Damage Criteria

To study the influence of fillings on rock failure. By turning to the Drucker-Prager strength model and cumulative damage criteria, investigations are made, with the nonlinear AUTODYN software, into crack propagation behaviors in crack-filled and unfilled specimens under uniaxial dynamic loading. Under investigations are crack initiation position, sequence and angle, and coalescence mode. According to the mode of propagation and coalescence, cracks are divided into three types, i.e., the tensile wing, the antiwing, and the horsetail. The simulation results show that under uniaxial dynamic loading, differences are found in initiation position, angle, and coalescence mode for specimens with cracks filled or otherwise. However, filling does not affect crack initiation sequence. Under the same loading, the damage to filled specimen is less severe than that to the unfilled specimen.

HIGH STRAIN RATE LOADING OF ZIRCALOY

1985 ◽  
Vol 46 (C5) ◽  
pp. C5-511-C5-516
Author(s):  
A. Kobayashi ◽  
S. Hashimoto ◽  
Li-lih Wang ◽  
M. Toba
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Strain Rate Loading

scholarly journals Experimental and Numerical Study of Fracture Behavior of Rock-Like Material Specimens with Single Pre-Set Joint under Dynamic Loading

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2690
Author(s):  
Bo Pan ◽  
Xuguang Wang ◽  
Zhenyang Xu ◽  
Lianjun Guo ◽  
Xuesong Wang
Keyword(s):  
Crack Initiation ◽  
Crack Propagation ◽  
Joint Angle ◽  
Simulation Software ◽  
Dissipated Energy ◽  
Energy Structure ◽  
Joint Angles ◽  
Crack Penetration ◽  
Before And After ◽  
The Impact

The Split Hopkinson Pressure Bar (SHPB) is an apparatus for testing the dynamic stress-strain response of the cement mortar specimen with pre-set joints at different angles to explore the influence of joint attitudes of underground rock engineering on the failure characteristics of rock mass structure. The nuclear magnetic resonance (NMR) has also been used to measure the pore distribution and internal cracks of the specimen before and after the testing. In combination with numerical analysis, the paper systematically discusses the influence of joint angles on the failure mode of rock-like materials from three aspects of energy dissipation, microscopic damage, and stress field characteristics. The result indicates that the impact energy structure of the SHPB is greatly affected by the pre-set joint angle of the specimen. With the joint angle increasing, the proportion of reflected energy moves in fluctuation, while the ratio of transmitted energy to dissipated energy varies from one to the other. NMR analysis reveals the structural variation of the pores in those cement specimens before and after the impact. Crack propagation direction is correlated with pre-set joint angles of the specimens. With the increase of the pre-set joint angles, the crack initiation angle decreases gradually. When the joint angles are around 30°–75°, the specimens develop obvious cracks. The crushing process of the specimens is simulated by LS-DYNA software. It is concluded that the stresses at the crack initiation time are concentrated between 20 and 40 MPa. The instantaneous stress curve first increases and then decreases with crack propagation, peaking at different times under various joint angles; but most of them occur when the crack penetration ratio reaches 80–90%. With the increment of joint angles in specimens through the simulation software, the changing trend of peak stress is consistent with the test results.

scholarly journals Crack Propagation in the Tibia Bone within Total Knee Replacement Using the eXtended Finite Element Method

2021 ◽  
Vol 11 (10) ◽  
pp. 4435
Author(s):  
Ho-Quang NGUYEN ◽  
Trieu-Nhat-Thanh NGUYEN ◽  
Thinh-Quy-Duc PHAM ◽  
Van-Dung NGUYEN ◽  
Xuan Van TRAN ◽  
...  
Keyword(s):  
Fatigue Crack ◽  
Crack Initiation ◽  
Crack Propagation ◽  
Fatigue Crack Initiation ◽  
Fracture Prevention ◽  
Patient Specific ◽  
Extended Finite Element ◽  
Tibia Bone ◽  
Age Related ◽  
Final Failure

Understanding of fracture mechanics of the human knee structures within total knee replacement (TKR) allows a better decision support for bone fracture prevention. Numerous studies addressed these complex injuries involving the femur bones but the full macro-crack propagation from crack initiation to final failure and age-related effects on the tibia bone were not extensively studied. The present study aimed to develop a patient-specific model of the human tibia bone and the associated TKR implant, to study fatigue and fracture behaviors under physiological and pathological (i.e., age-related effect) conditions. Computed tomography (CT) data were used to develop a patient-specific computational model of the human tibia bone (cortical and cancellous) and associated implants. First, segmentation and 3D-reconstruction of the geometrical models of the tibia and implant were performed. Then, meshes were generated. The locations of crack initiation were identified using the clinical observation and the fatigue crack initiation model. Then, the propagation of the crack in the bone until final failure was investigated using the eXtended finite element method (X-FEM). Finally, the obtained outcomes were analyzed and evaluated to investigate the age-effects on the crack propagation behaviors of the bone. For fatigue crack initiation analysis, the stress amplitude–life S–N curve witnessed a decrease with increasing age. The maximal stress concentration caused by cyclic loading resulted in the weakening of the tibia bone under TKR. For fatigue crack propagation analysis, regarding simulation with the implant, the stress intensity factorand the energy release rate tended to decrease, as compared to the tibia model without the implant, from 0.152.5 to 0.111.9 (MPa) and from 10240 to 5133 (J), respectively. This led to the drop in crack propagation speed. This study provided, for the first time, a detailed view on the full crack path from crack initiation to final failure of the tibia bone within the TKR implant. The obtained outcomes also suggested that age (i.e., bone strength) also plays an important role in tibia crack and bone fracture. In perspective, patient-specific bone properties and dynamic loadings (e.g., during walking or running) are incorporated to provide objective and quantitative indicators for crack and fracture prevention, during daily activities.

scholarly journals A New Set-Up to Investigate Plastic Deformation of Face Centered Cubic Metals in High Strain Rate Loading

2014 ◽  
Vol 8 (2) ◽  
Author(s):  
Ehsan Etemadi ◽  
Jamal Zamani ◽  
Alessandro Francesconi ◽  
Mohammad V. Mousavi ◽  
Cinzia Giacomuzzo
Keyword(s):  
Plastic Deformation ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Face Centered Cubic ◽  
Cubic Metals ◽  
Face Centered ◽  
Set Up ◽  
Strain Rate Loading

Modeling of Fatigue Crack Propagation

2004 ◽  
Vol 126 (1) ◽  
pp. 77-86 ◽  
Author(s):  
Yanyao Jiang ◽  
Miaolin Feng
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Initiation ◽  
Crack Propagation ◽  
Crack Growth ◽  
Fatigue Damage ◽  
Fatigue Crack Propagation ◽  
Fatigue Crack Initiation ◽  
Cyclic Plasticity ◽  
R Ratio

Fatigue crack propagation was modeled by using the cyclic plasticity material properties and fatigue constants for crack initiation. The cyclic elastic-plastic stress-strain field near the crack tip was analyzed using the finite element method with the implementation of a robust cyclic plasticity theory. An incremental multiaxial fatigue criterion was employed to determine the fatigue damage. A straightforward method was developed to determine the fatigue crack growth rate. Crack propagation behavior of a material was obtained without any additional assumptions or fitting. Benchmark Mode I fatigue crack growth experiments were conducted using 1070 steel at room temperature. The approach developed was able to quantitatively capture all the important fatigue crack propagation behaviors including the overload and the R-ratio effects on crack propagation and threshold. The models provide a new perspective for the R-ratio effects. The results support the notion that the fatigue crack initiation and propagation behaviors are governed by the same fatigue damage mechanisms. Crack growth can be treated as a process of continuous crack nucleation.

Sign in / Sign up

Export Citation Format

Share Document