A Narrow Band Pass Filter Using Technology Surface Mount Technology on Radar Frequency Generators

2016 ◽  
Vol 3 (1) ◽  
pp. 136
Author(s):  
I Dewa Putu Hermida ◽  
Deni Permana Kurniadi ◽  
Iqbal Syamsu
Keyword(s):  
Stop Band ◽  
Band Width ◽  
Signal Frequency ◽  
Band Pass Filter ◽  
Frequency Range ◽  
Pass Filter ◽  
Fmcw Radar ◽  
Frequency Generator ◽  
Band Depth ◽  
Radar Frequency

A BPF using SMT components. A cut-off frequency on a filter under cooling below LPF which works at  freq 310 MHz, while the cut-off frequency below a filter under cooling HPF which works at freq 306 MHz, so that the width of the band This filter is a type of narrow bandwidth filter 4 MHz. An 7 poles filter order with the aim to increase the steepness of the filter is generated, using the elliptic filter family or causer. Stop band width (Fs) to filter under cooling below about 20% in the frequency range 372 MHz, with stop band depth (As) of about 55 dB, while the stop band width (Fs) to filter under cooling of about 20% in the frequency range 245 MHz, with stop band depth (As) of about 55 dB. This filter is designed to pass the signal frequency division results DRO with a CF of 9856 MHz. Using SMT components, this circuit becomes very small and compact and has a high Q. The results of the simulation are generated, then this filter can realized system FMCW radar frequency generator.

scholarly journals Design of UWB Filter with WLAN Notch

2012 ◽  
Vol 2012 ◽  
pp. 1-4 ◽  
Author(s):  
Harish Kumar ◽  
MD. Upadhayay
Keyword(s):  
Circuit Simulation ◽  
Ground Plane ◽  
Stop Band ◽  
Simulation Software ◽  
Pass Band ◽  
Area Network ◽  
Band Pass Filter ◽  
Frequency Range ◽  
Pass Filter ◽  
Band Pass

UWB technology- (operating in broad frequency range of 3.1–10.6 GHz) based filter with WLAN notch has shown great achievement for high-speed wireless communications. To satisfy the UWB system requirements, a band pass filter with a broad pass band width, low insertion loss, and high stop-band suppression are needed. UWB filter with wireless local area network (WLAN) notch at 5.6 GHz and 3 dB fractional bandwidth of 109.5% using a microstrip structure is presented. Initially a two-transmission-pole UWB band pass filter in the frequency range 3.1–10.6 GHz is achieved by designing a parallel-coupled microstrip line with defective ground plane structure using GML 1000 substrate with specifications: dielectric constant 3.2 and thickness 0.762 mm at centre frequency 6.85 GHz. In this structure aλ/4 open-circuited stub is introduced to achieve the notch at 5.6 GHz to avoid the interference with WLAN frequency which lies in the desired UWB band. The design structure was simulated on electromagnetic circuit simulation software and fabricated by microwave integrated circuit technique. The measured VNA results show the close agreement with simulated results.

Compact multiple electromagnetic band gap (EBG) cells based ultra wide band (UWB) filter with improved stop-band characteristics

Circuit World ◽  
2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Masood Molimoli Hajamohideen ◽  
Sreeja Balakrishanapillai Suseela
Keyword(s):  
Stop Band ◽  
Wide Band ◽  
Ultra Wide Band ◽  
Pass Band ◽  
Band Pass Filter ◽  
Frequency Range ◽  
Pass Filter ◽  
Electromagnetic Band Gap ◽  
Content Type ◽  
Band Pass

Purpose The purpose of the study is – in Microwave filter design, the performances of passive components are deteriorated by parasitics at gigahertz (GHz) frequency range. A compact and multi-stack electromagnetic band gap (EBG) structure is proposed with improved stop band characteristics at GHz frequency range in this work. This paper proposes a new design for ultra wide band pass filter (resonator BPF) with periodically loaded one-dimensional EBG to achieve the harmonic suppression. This basic EBG structure is developed with combination of a signal strip and ground plane in the slotted section. The resonator BPF is loaded with one EBG, two EBG and three EBGs to improve the stop-band rejection. Design/methodology/approach The proposed filter is with multi-stack EBG cell for achieving good pass band and stop bands performance. Circuit model is analyzed in Section 2. Section 3 discuses band pass filter loaded with one EBG. In Sections 4 and 5, filter with two and three EBG loaded resonators are discussed, respectively. Section 6 is concluded with comparison of simulation and measured results. Findings The stop-band rejection is 20 dB, 40 dB and 50 dB, respectively, in the frequency range of 6 GHz to 20 GHz. The simulation analysis is carried out with advanced system design software. To validate the simulation results, proposed structure is fabricated, and results are found to be in good agreement. Originality/value This paper accounts for designing resonator BPF, which has slow wave pass band and stop band characteristics. Second and third harmonics are suppressed using multi-stack EBG. Various stacks with basic designs are proposed and improved results have been demonstrated which is open for future research.

Novel Low-Pass Microwave Filter Based on Rectangular Ring DGS

2013 ◽  
Vol 273 ◽  
pp. 371-374
Author(s):  
Bao Ping Li ◽  
Yan Liang Zhang
Keyword(s):  
Stop Band ◽  
Center Frequency ◽  
Pass Band ◽  
Band Pass Filter ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Compact Size ◽  
Low Pass

Due to the frequency response periodicity of distributed transmission line, microstrip band-pass filter usually produces parasitic pass-band and outputs harmonics away from the center frequency of main pass-band. Based on the study of rectangular ring defected ground structure, a 5-order microstrip LPF(low-pass filter) was designed using the single-pole band-stop and slow-wave characteristics of the rectangular ring DGS(Defected Ground Structure) and SISS(Step-Impedance Shunt Stub) structure. Compared with traditional LPF, this LPF presents the advantages of compact size, low insertion loss, broad stop-band and high steep. It also validates the requirements of miniaturization and high performance for filters.

SELF-TUNING BIQUAD BAND-PASS FILTER

2013 ◽  
Vol 22 (03) ◽  
pp. 1350008 ◽  
Author(s):  
GORAN JOVANOVIĆ ◽  
DARKO MITIĆ ◽  
MILE STOJČEV ◽  
DRAGAN ANTIĆ
Keyword(s):  
Dynamic Range ◽  
Signal Frequency ◽  
Band Pass Filter ◽  
Central Frequency ◽  
Pass Filter ◽  
Input Signal Frequency ◽  
Bicmos Technology ◽  
Self Tuning ◽  
Band Pass ◽  
Constant Bandwidth

One approach to design self-tuning gm-C biquad band-pass filter is considered in this paper. The phase control loop is introduced to force filter central frequency to be equal to input signal frequency what is achieved by adjusting the amplifier transconductance gm. Thanks to that, the filter is robust to parameter perturbations and it can be used as a selective amplifier. In the full tuning range, it has a constant maximum gain at central frequency as well as a constant bandwidth. The 0.25 μm SiGe BiCMOS technology was used during design and verification of the band-pass filter. The filter has 26 dB gain, quality factor Q = 20 and central frequency up to 150 MHz. Simulation results indicate that the total in-band noise is 59 μV rms , the output third intercept point OIP3 = 4.36 dB and the dynamic range is 35 dB. Maximal power consumption at 3 V power supply is 1.115 mW.

COMPACT MICROSTRIP BAND-PASS FILTER FOR EMI REDUCTION

2015 ◽  
Vol 77 (12) ◽  
Author(s):  
Kabir Ibrahim Jahun ◽  
Hussein Mohamed Hagi Hassan Abdirahman Mohamud Shire ◽  
Ali Orozi Sougui ◽  
S. H. Dahlan
Keyword(s):  
Filter Design ◽  
Stop Band ◽  
Band Pass Filter ◽  
Defected Ground Structure ◽  
Coupled Line ◽  
Pass Filter ◽  
Filter Structure ◽  
Coupled Lines ◽  
Band Pass ◽  
Compact Design

Compact microstrip band-pass filter design using parallel coupled lines is presented in this paper. The microstrip lines are calculated and constructed using CST studio with two input and output ports of the filter structure are printed over Defected Ground Structure (DGS).The proposed symmetrical structure offers a simple and compact design while exhibiting an improved stop-band characteristics in comparison to conventional coupled microstrip line filter structure. The simulation and measurements of 2GHz prototype band pass filter are presented. The measured result agrees well with the simulation data. Compared with conventional parallel coupled line band pass filter, the second, third and fourth spurious responses are suppressed; in addition, the size of the prototype filter circuit is reduced up to 20.8%.  

Fast Locking Time Biquadratic Band-Pass Filter Utilizing Nonlinear Sliding-Mode Controller

2020 ◽  
pp. 2150154
Author(s):  
Darko Mitić ◽  
Goran Jovanović ◽  
Mile Stojčev ◽  
Dragan Antić
Keyword(s):  
Input Signal ◽  
Sliding Mode ◽  
Design Procedure ◽  
Signal Frequency ◽  
Sliding Mode Controller ◽  
Band Pass Filter ◽  
Central Frequency ◽  
Pass Filter ◽  
Bicmos Technology ◽  
Band Pass

This paper considers design procedure of fast locking time self-tuning [Formula: see text] biquadratic band-pass filter with nonlinear sliding mode control. A sliding mode controller is building block of the phase control loop (PCL) involved to push central frequency to reach input signal frequency very fast, approximately 100–200[Formula: see text]ns. The sliding mode controller is realized by using a tunable delay line, enabling optimal filter locking time for different input signal frequencies. The filter possesses low sensitivity to component discrepancy and is applied as a selective amplifier. The 0.13[Formula: see text][Formula: see text]m SiGe BiCMOS technology has been utilized for design and verification of the presented filter. This filter has central frequency up to 220[Formula: see text]MHz, quality factor [Formula: see text] and 25[Formula: see text]dB gain.

Sign in / Sign up

Export Citation Format

Share Document