Numerical Simulation of Nanofluid Heat Transfer in a Double-Layered Microchannel Heat Sink Using Two Phase Mixture Model

2016 ◽  
Vol 5 (1) ◽  
pp. 139-147 ◽  
Author(s):  
M. Kalteh ◽  
R. Kouhikamali ◽  
S. Akbari
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Mixture Model ◽  
Heat Sink ◽  
Microchannel Heat Sink ◽  
Two Phase ◽  
Phase Mixture

Numerical Simulation of Flow in a Horizontal Sedimentation Tank

2011 ◽  
Vol 130-134 ◽  
pp. 3624-3627
Author(s):  
W.L. Wei ◽  
Zhang Pei ◽  
Y.L. Liu
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Secondary Flow ◽  
Mixture Model ◽  
Turbulence Model ◽  
Two Phase ◽  
Sedimentation Tank ◽  
Phase Mixture ◽  
Good Agreement

In this paper, we use two-phase mixture model and the Realizable k-ε turbulence model to numerically simulate the advection secondary flow in a sedimentation tank. The PISO algorithm is used to decouple velocity and pressure. The comparisons between the measured and computed data are in good agreement, which indicates that the model can fully simulate the flow field in a sedimentation tank.

Numerical Investigation of Flow Boiling in a Manifold Microchannel Heat Sink With Conjugate Heat Transfer

2019 ◽  
Author(s):  
Zhichuan Sun ◽  
Yang Luo ◽  
Junye Li ◽  
Wei Li ◽  
Jingzhi Zhang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Numerical Investigation ◽  
Heat Sink ◽  
Conjugate Heat Transfer ◽  
Flow Boiling ◽  
High Heat Flux ◽  
Microchannel Heat Sink ◽  
Two Phase ◽  
Boiling Process ◽  
Manifold Microchannel

Abstract The manifold microchannel heat sink receives an increasing number of attention lately due to its high heat flux dissipation. Numerical investigation of boiling phenomena in manifold microchannel (MMC) heat sinks remains a challenge due to the complexity of fluid route and the limitation of numerical accuracy. In this study, a computational fluid dynamics (CFD) approach including subcooled two-phase flow boiling process and conjugate heat transfer effect is performed using a MMC unit cell model. Different from steady-state single phase prediction in MMC heat sink, this type of modeling allows for the transient simulation for two-phase interface evolution during the boiling process. A validation case is conducted to validate the heat transfer phenomenon among three phases. Besides, this model is used for the assessment of the manifold dimensions in terms of inlet and outlet widths at the mass flux of 1300 kg/m2·s. With different ratios of inlet-to-outlet area, the thermal resistances remain nearly stable.

Two-Phase Performance of a Hybrid Jet Plus Multipass Microchannel Heat Sink

2019 ◽  
Vol 12 (1) ◽  
Author(s):  
Shailesh N. Joshi ◽  
Danny J. Lohan ◽  
Ercan M. Dede
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Rate ◽  
Heat Sink ◽  
Maximum Pressure ◽  
Microchannel Heat Sink ◽  
Large Area ◽  
Two Phase ◽  
Maximum Heat ◽  
Flow Rates

Abstract The heat transfer and fluid flow performance of a hybrid jet plus multipass microchannel heat sink in two-phase operation is evaluated for the cooling of a single large area, 3.61 cm2, heat source. The two-layer branching microchannel heat sink is evaluated using HFE-7100 as the coolant at three inlet volumetric flow rates of 150, 300, and 450 ml/min. The boiling performance is highest for the flow rate of 450 ml/min with the maximum heat flux value of 174 W/cm2. Critical heat flux (CHF) was observed at two of the tested flow rates, 150 and 300 ml/min, before reaching the maximum operating temperature for the serpentine heater. At 450 ml/min, the heater reached the maximum allowable temperature prior to observing CHF. The maximum pressure drop for the heat sink is 34.1 kPa at a heat flux of 164 W/cm2. Further, the peak heat transfer coefficient value of the heat sink is 28,700 W/m2 K at a heat flux value of 174 W/cm2 and a flow rate of 450 ml/min. Finally, a validated correlation of the single device cooler is presented that predicts heat transfer performance and can be utilized in the design of multidevice coolers.

The effects of tape insert material on the flow and heat transfer in a nanofluid-based double tube heat exchanger: Two-phase mixture model

2019 ◽  
Vol 156 ◽  
pp. 397-409 ◽  
Author(s):  
Ali Karimi ◽  
Abdullah A.A.A. Al-Rashed ◽  
Masoud Afrand ◽  
Omid Mahian ◽  
Somchai Wongwises ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Mixture Model ◽  
Two Phase ◽  
Tube Heat Exchanger ◽  
Flow And Heat Transfer ◽  
Phase Mixture
Sign in / Sign up

Export Citation Format

Share Document