Acoustic Measurement of Subglottic Stenosis

1996 ◽  
Vol 105 (7) ◽  
pp. 504-509 ◽  
Author(s):  
Judith M. Czaja ◽  
Thomas V. McCaffrey

A device that determines cross-sectional area (CSA) of the airway by acoustic ref lections (Hood, Inc) was used to measure subglottic area. Airway models were made from Plexiglas rings with known internal dimensions similar to clinically encountered stenoses of various lengths and diameters. Acoustic measurements of airway area were made and compared to actual CSA. There is a strong correlation between CSA measured acoustically and the actual area of simulated stenoses. However, when the CSA of the stenosis was <0.64 cm2, the signal was impaired, resulting in overestimation of the stenotic CSA. In simulated stenoses with a CSA of <0.38 cm2, acoustic measurement of the CSA beyond the stenotic segment was unreliable. Determination of the origin of stenosis was accurate with this method. The CSA of cadaver airways was also measured acoustically. The CSA 2.0 cm below the glottis of normal airways in males ranged from 1.28 to 2.74 cm2 and in females 0.87 to 1.43 cm2, with means of 2.16 and 1.09 cm2. It appears that acoustic measurement of CSA of subglottic stenosis is a feasible clinical technique that yields dimensions of the airway in situations in which direct measurements are impossible. It was suggested that this technique be used for assessment of subglottic stenosis and evaluation of the efficacy of treatment of subglottic stenosis.

2020 ◽  
Vol 0 (4) ◽  
pp. 19-24
Author(s):  
I.M. UTYASHEV ◽  
◽  
A.A. AITBAEVA ◽  
A.A. YULMUKHAMETOV ◽  
◽  
...  

The paper presents solutions to the direct and inverse problems on longitudinal vibrations of a rod with a variable cross-sectional area. The law of variation of the cross-sectional area is modeled as an exponential function of a polynomial of degree n . The method for reconstructing this function is based on representing the fundamental system of solutions of the direct problem in the form of a Maclaurin series in the variables x and λ. Examples of solutions for various section functions and various boundary conditions are given. It is shown that to recover n unknown coefficients of a polynomial, n eigenvalues are required, and the solution is dual. An unambiguous solution was obtained only for the case of elastic fixation at one of the rod’s ends. The numerical estimation of the method error was made using input data noise. It is shown that the error in finding the variable crosssectional area is less than 1% with the error in the eigenvalues of longitudinal vibrations not exceeding 0.0001.


1993 ◽  
Vol 75 (6) ◽  
pp. 2811-2819 ◽  
Author(s):  
O. Hilberg ◽  
F. T. Jensen ◽  
O. F. Pedersen

To evaluate the accuracy of the acoustic reflection (AR) technique for determination of nasal cavity cross-sectional areas, the area-distance function of both sides of the nose was determined in 10 subjects and compared with magnetic resonance imaging (MRI). Interindividual variation for the correlation between MRI and AR was seen, but in general the areas from 1 to 6 cm into the nasal cavity measured by AR were larger than areas measured by MRI, especially where the surface was most convoluted. The total volume for this region was 6.47 +/- 1.83 (SD) cm3 for AR and 5.65 +/- 1.34 cm3 for MRI. It was demonstrated that this could be due to errors in calculation of the areas on the basis of MRI and AR. In the posterior part of the nasal cavity and the epipharynx, there was a convincingly higher correlation between acoustic measurements and a scan perpendicular to the assumed geometrical axis of the epipharynx than between acoustic measurements and coronal scanning. This indicates that the sound axis roughly follows the geometrical axis. In a model of two tubes (nasal cavities) joined in a larger tube (the epipharynx), closure of the posterior part of the latter revealed that the contralateral nasal cavity is likely to cause overestimation of the posterior part of the epipharynx during AR compared with MRI.


2007 ◽  
Vol 391 (1) ◽  
pp. 118-123 ◽  
Author(s):  
Jeremy McMinis ◽  
Rene Crombez ◽  
Eva Montalvo ◽  
Weidian Shen

2018 ◽  
Vol 224 ◽  
pp. 05023 ◽  
Author(s):  
Yuri Ivanov ◽  
Viktor Pakhomov ◽  
Sergei Kambulov ◽  
Dmitri Rudoi

Many technologies of the agro-industrial complex are associated with the need for a quality blending of two or more components. These include the processes of obtaining biodiesel fuel based on vegetable oils, obtaining aqueous emulsions of fats in the production of mixed fodders. In this process, the most effective is the use of a hydrodynamic mixer, the main design parameters of which are determined in the process of investigation. The design of a nozzle with a variable cross-sectional area is calculated, which allows to control the mixing process. The obtained mathematical dependences quite fully characterize the features of the work and the requirements for the design of the ejector installed in the hydrodynamic mixer to create cavitation with the required intensity.


Cellulose ◽  
2019 ◽  
Vol 26 (8) ◽  
pp. 4693-4706 ◽  
Author(s):  
Hangbo Yue ◽  
Juan C. Rubalcaba ◽  
Yingde Cui ◽  
Juan P. Fernández-Blázquez ◽  
Chufen Yang ◽  
...  

2015 ◽  
Vol 1083 ◽  
pp. 111-117
Author(s):  
Xi Ying Yang ◽  
Ou Yang Ting ◽  
You Qing Fei

Cross sectional area of single filaments, a key parameter to characterize fiber properties, was experimentally studied using a desktop scanning electron microscope. Three different methods are employed based on the pixel area, averaged diameter and single diameter measurements, respectively. Results have shown that all three methods can achieve accurate measurement results once the axis of fiber sample is kept parallel to the electron beam. Significant errors are generated for the fiber samples with their axis tilted, which may frequently occur as a sample prepared. For circular fibers, a single diameter measured from tilted fibers is sufficient to determine their cross sectional area at high precision with COV values below 1.6%. By selecting an appropriate method, a desktop SEM can serve as a convenient and powerful tool for accurate determination of cross sectional area as well as morphological observation.


Sign in / Sign up

Export Citation Format

Share Document