Assessment of die material manufactured using the lost foam casting process for hot press forming

2012 ◽  
Vol 226 (7) ◽  
pp. 1213-1223 ◽  
Author(s):  
Nak-Hyun Kim ◽  
Yong-Phil Jeon ◽  
Chung-Gil Kang
Keyword(s):  
Casting Process ◽  
Lost Foam Casting ◽  
Hot Press ◽  
Press Forming ◽  
Hot Press Forming ◽  
Die Material ◽  
Lost Foam

Experimental Assessment of High Temperature Formability of Boron Steel Sheet Manufactured With a Spring Compound Bending Die

2012 ◽  
Vol 134 (2) ◽  
Author(s):  
Yang Li ◽  
Yong-Phil Jeon ◽  
Chung-Gil Kang
Keyword(s):  
Mechanical Properties ◽  
Heating Temperature ◽  
Boron Steel ◽  
Hot Press ◽  
Forming Process ◽  
Steel Sheets ◽  
Press Forming ◽  
Bending Process ◽  
Tension Testing ◽  
Hot Press Forming

Bending behavior occurs in the hot press forming process, resulting in many cases of failure during forming. To address the problem of cracking and improve the formability and mechanical properties of boron steel sheets in the bending process, an experiment has been carried out by using a spring compound bending die. Also, a comparison has been made between the traditional U-bending die and the spring compound bending die with regard to formability. The influence of the parameters for hot press forming such as the heating temperature, punch speed, and die radii on the mechanical properties and microstructure was analyzed by tension testing and metallographic observations.

Synthesis and Characterization of New Refractory Coatings Based on Talc, Cordierite, Zircon and Mullite Fillers for Lost Foam Casting Process

2014 ◽  
Vol 59 (1) ◽  
pp. 89-95 ◽  
Author(s):  
A. Prstić ◽  
Z. Aćimović-Pavlović ◽  
A. Terzić ◽  
L. Pavlović
Keyword(s):  
Microstructural Analysis ◽  
Casting Process ◽  
Lost Foam Casting ◽  
X Ray Diffraction ◽  
X Ray ◽  
Software Application ◽  
Design And Optimization ◽  
Refractory Coatings ◽  
Particle Size And Shape ◽  
Lost Foam

Abstract Refractory coatings based on different refractory fillers (talc, cordierite, zircon and mullite) for application in Lost Foam casting process were investigated. Design and optimization of the coatings composition with controlled, rheological properties included, and consequently synthesis were achieved by application of different coating components, namely different suspension agents and fillers and by alteration of the coating production procedure. Morphologic and microstructural analysis of fillers was carried out by means of scanning electronic microscope. X-ray diffraction analysis by means of X-ray diffractometer was applied in determination and monitoring the phase composition changes of the refractory fillers. An analysis of the particle size and shape was carried out by means of the PC software application package OZARIA 2.5. To assess the effects of application of individual refractory coatings, a detailed investigation of structural and mechanical properties of the moldings obtained was performed. Highlight was placed on revealing and analyzing surface and volume defects present on moldings. Radiographic molding tests were carried out by means of the X-ray device SAIFORT type-S200. Attained results are essential for the synthesis of refractory coatings based on high-temperature fillers and their applications in Lost Foam casting process for manufacturing of moldings with in-advance-set properties.

Numerical Simulation of Molten Metal-Polymeric Foam Interface Velocity During Lost Foam Casting

2001 ◽  
Author(s):  
Sayavur I. Bakhtiyarov ◽  
Ruel A. Overfelt
Keyword(s):  
Molten Metal ◽  
Flow Model ◽  
Interface Velocity ◽  
Casting Process ◽  
Lost Foam Casting ◽  
Foam Material ◽  
Polymeric Foam ◽  
Gaseous Products ◽  
3D Software ◽  
Lost Foam

Abstract A novel multiphase flow model is presented for describing the pyrolisis of polymeric foam material in a lost foam casting process. FLOW-3D software (Flow Science, Inc.) has been used to simulate liquid metal filling dynamics and the molten metal-polymeric foam interface velocity in foam patterns of rectangular shape. The effect of the degradation gaseous products on the molten metal-polymeric foam interface velocity was taken into consideration through specially written sub-routing program. The results of the simulations are compared with the previously obtained experimental data for the lost foam iron casting.

scholarly journals Study on Hot Press Forming Process of Large Curvilinear Generatrix Workpiece of Ti55 High-Temperature Titanium Alloy

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 827 ◽  
Author(s):  
Fengyong Wu ◽  
Wenchen Xu ◽  
Zhongze Yang ◽  
Bin Guo ◽  
Debin Shan
Keyword(s):  
Titanium Alloy ◽  
High Temperature ◽  
Fem Simulation ◽  
Alloy Sheet ◽  
Rolled Sheet ◽  
Strain Rates ◽  
Hot Press ◽  
Forming Process ◽  
Press Forming ◽  
Hot Press Forming

In order to manufacture complex curvilinear generatrix workpieces of high-temperature titanium alloy, the hot tensile behavior of Ti55 alloy sheet was tested and the hot press forming process was investigated using Finite Element Method (FEM) simulation and experiment. The hot tensile experiments of Ti55 rolled sheet were conducted at the temperatures of 800–900 °C with the strain rates of 0.001–0.1 s−1. According to the results of hot tensile tests and microstructure evolution, the proper hot press forming parameters were determined as the temperature of 850 °C and the strain rates of 0.001–0.01 s−1. The wrinkling mechanism in the transition region was analyzed and the initial blank sheet geometry was optimized by FE simulation of hot press forming. The two-step hot press forming process was better to produce the complex sheet workpiece of Ti55 alloy than the one-step hot forming scheme, which could restrain the wrinkling trend and ensure the microstructure and mechanical properties of the hot formed workpieces.

Sign in / Sign up

Export Citation Format

Share Document