Numerical investigation of the diffuser throat length effect on a transonic centrifugal compressor

2021 ◽  
pp. 095440622110401
Author(s):  
Qingkuo Li ◽  
Yingjie Zhang ◽  
Yi Wang ◽  
Ge Han ◽  
Yanfeng Zhang ◽  
...  
Keyword(s):  
Numerical Investigation ◽  
Centrifugal Compressor ◽  
Flow Direction ◽  
Divergence Angle ◽  
Centrifugal Compressors ◽  
Vaned Diffuser ◽  
Stall Margin ◽  
Transonic Centrifugal Compressor ◽  
Fluid Pressurization ◽  
Large Flow

Vaned diffuser inlet flow uniform is challenging when the impeller is throttled to stall. In this study, we extend the stable operating range of the compressor by improving the uniform flow of the diffuser inlet. First, a numerical investigation of a transonic centrifugal compressor with a vaned diffuser is presented and compared against test data. Then, a new diffuser parameterization method is pro- posed, and the throat feature of a pipe diffuser is successfully applied to parameterized vane diffusers. The influence of the throat length and divergence angle of the diffuser on the performance of the centrifugal compressor is studied via steady and non-linear harmonic simulations. Throat length delays the time of fluid pressurization and accommodates large flow instabilities from upstream—this widens the stall margin but increases mixing loss. Divergence angle affects compressor performance. Stage peak efficiency increases by about 0.58% as the divergence angle increases from 3.79° to 5.79° but drops to about 2.46% as the divergence angle further increases from 5.79° to 11.79°. This is because the boundary layers in the diffuser channel thicken with increasing divergence angle; additionally, the fluid near the hub-pressure side first becomes unstable, then flow separation occurs along the flow direction, which results in a large flow loss. Detailed performance maps of centrifugal compressors with different throat lengths and divergence angles are given to provide a reference for designing transonic centrifugal compressors.

Investigation of Unsteady Impeller-Diffuser Interaction in a Transonic Centrifugal Compressor Stage

2010 ◽  
Author(s):  
Yangwei Liu ◽  
Baojie Liu ◽  
Lipeng Lu
Keyword(s):  
Centrifugal Compressor ◽  
Flow Direction ◽  
Equation System ◽  
Compressor Stage ◽  
Spatial Correlations ◽  
Tip Leakage Flow ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Transonic Centrifugal Compressor ◽  
Steady Simulation

In this paper, unsteady impeller-diffuser interaction in a transonic centrifugal compressor stage, which is composed of an impeller with splitter blade and a vaned diffuser, was studied numerically. The unsteady interaction has a significant impact on the time-averaged flow, which are presented by the so-called deterministic correlations in the average-passage equation system (APES) proposed by Adamczyk. Both steady and unsteady simulations were carried out at the design and off-design conditions. Results from the steady and unsteady simulations were compared to highlight the importance of the unsteady interactions and to help assess the shortcomings of simple mixing-plane methods. The comparisons indicate that the unsteady interactions should be considered in the simulations since the differences between the time averaged unsteady results and steady simulation results are significant especially at off-design conditions. Then the interactions between impeller and diffuser were studied in detail to advance the understanding of the flow physics involved. The results show that the impeller/diffuser interaction can affect a range of 30% impeller chord from impeller trailing edge on impeller performance, while whole chord length on diffuser performance. The potential effects of the diffuser cause an unsteady pressure disturbance at the impeller exit, leading to the unsteadiness of impeller load, tip leakage flow and losses. While the unsteadiness of impeller exit flow cause period varieties of inlet flow conditions for the diffuser and have large impacts on diffuser performance. Based on the unsteady results, deterministic correlations in the APES framework were computed and analyzed in order to reveal some shortcomings of present deterministic correlations models and to make some contributions to the modeling development. The distribution characteristics of deterministic correlations were studied. The study indicates that the deterministic correlations in the impeller and diffuser have the similar magnitudes, and that the correlations in the passages have large gradients in circumferential direction and decrease rapidly in flow direction especially in the vaneless space. The deterministic correlations at the impeller/diffuser interface were compared with their spatial correlations using the framework of the deterministic decomposition. The comparisons show that the spatial correlations have some discrepancies with the total deterministic correlations at the impeller/diffuser interface.

Improvement of the Flow Range of Transonic Centrifugal Compressors With a Low-Solidity Cascade Diffuser

2000 ◽  
Author(s):  
Hiroshi Hayami
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Pressure Ratio ◽  
Input Power ◽  
Velocity Of Sound ◽  
Centrifugal Compressors ◽  
Vaned Diffuser ◽  
Transonic Centrifugal Compressor ◽  
Series Of Experiments ◽  
Low Solidity Cascade Diffuser

If the pressure ratio of a typical single-stage centrifugal compressor is larger than four, the velocity relative to the impeller and to the diffuser exceeds the velocity of sound. The flow range of transonic centrifugal compressors with a vaned diffuser is usually very narrow. Low-solidity cascade diffusers with solidity 0.69 have been successfully applied as a part of the diffuser system of a transonic centrifugal compressor. On the basis of this type of diffuser, a series of experiments to broaden the operating range are discussed focusing on the control of the geometry of impeller and/or diffuser; one was to reduce the inducer blade turning upstream of the throat, and the other was to reduce the inlet passage width of diffuser. The milder inducer blade camber realized the improvement in flow range by 1.5 times to the original one. Regarding the diffuser inlet passage width contraction, the flow range was not broadened so much owing to the change in impeller characteristics, but the input power was reduced and then the high speed efficiency was much improved.

scholarly journals Surge Margin Optimization of Centrifugal Compressors Using a New Objective Function Based on Local Flow Parameters

2019 ◽  
Vol 4 (4) ◽  
pp. 42
Author(s):  
Johannes Ratz ◽  
Sebastian Leichtfuß ◽  
Maximilian Beck ◽  
Heinz-Peter Schiffer ◽  
Friedrich Fröhlig
Keyword(s):  
Objective Function ◽  
Centrifugal Compressor ◽  
Computational Effort ◽  
Angle Distribution ◽  
Centrifugal Compressors ◽  
Local Flow ◽  
Vaned Diffuser ◽  
Flow Parameters ◽  
Surge Margin ◽  
Beta Angle

Currently, 3D-CFD design optimization of centrifugal compressors in terms of the surge margin is one major unresolved issue. On that account, this paper introduces a new kind of objective function. The objective function is based on local flow parameters present at the design point of the centrifugal compressor. A centrifugal compressor with a vaned diffuser is considered to demonstrate the performance of this approach. By means of a variation of the beta angle distribution of the impeller and diffuser blade, 73 design variations are generated, and several local flow parameters are evaluated. Finally, the most promising flow parameter is transferred into an objective function, and an optimization is carried out. It is shown that the new approach delivers similar results as a comparable optimization with a classic objective function using two operating points for surge margin estimation, but with less computational effort since no second operating point near the surge needs to be considered.

Surge Inception in a Transonic Centrifugal Compressor Stage

2011 ◽  
Author(s):  
Isabelle Tre´binjac ◽  
Nicolas Bulot ◽  
Xavier Ottavy ◽  
Nicolas Buffaz
Keyword(s):  
Centrifugal Compressor ◽  
Short Wavelength ◽  
Stokes Equations ◽  
Pressure Sensors ◽  
Experimental Investigations ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Choked Flow ◽  
Centrifugal Compressor Stage ◽  
Transonic Centrifugal Compressor

Numerical and experimental investigations were conducted in a transonic centrifugal compressor stage composed of a backswept splittered unshrouded impeller and a vaned diffuser. Unsteady 3D simulations were performed with the code elsA that solves the turbulent averaged Navier-Stokes equations, at three operating points: choked flow, peak efficiency and near surge. Unsteady pressure measurements up to 150 kHz were carried out in the entry zone of the vaned diffuser (in the vaneless space and in the semi-vaneless space) when the compressor came into surge. These static pressure sensors were mounted on the shroud enwall. The paper focuses on the vaneless and semi-vaneless space where the surge originates. A detailed analysis of the flow pattern coming from the unsteady computations from choked flow towards surge led to identify the physical mechanisms involved in the surge inception. It is shown that, when approaching surge, the flow is destabilized by a severe modification of the shock system in the vaned diffuser inlet. The first perturbation is acquired from the transducer located just upstream of the shock foot (i.e. on the vane suction side surface), indicating a movement of the shock towards the vaneless space. This perturbation travels upstream and leads to the strongest short-wavelength perturbation acquired from the transducer located just upstream of the vane leading edge. This strongest short-wavelength perturbation which level may reach almost four times the mean exit pressure value triggers the full scale instability.

The Use of Cascade Technology in Centrifugal Compressor Vaned Diffuser Design

1972 ◽  
Vol 94 (3) ◽  
pp. 187-192 ◽  
Author(s):  
R. C. Pampreen
Keyword(s):  
Centrifugal Compressor ◽  
Centrifugal Compressors ◽  
Vaned Diffuser ◽  
Circular Arc ◽  
Performance Results

This paper highlights some results from experience with use of cascade technology in the design of diffusers for centrifugal compressors. The designs consisted of conformally transformed tandem blade-rows using 65-Series and double-circular-arc vane sections. Performance results are presented and comparisons to conventional diffuser data are made.

Unsteady Effects of Blade Row Interaction on Flow Field and Aerodynamic Performance of a Transonic Centrifugal Compressor Impeller

2021 ◽  
Author(s):  
Kazutoyo Yamada ◽  
Kosuke Kubo ◽  
Kenichiro Iwakiri ◽  
Yoshihiro Ishikawa ◽  
Hirotaka Higashimori
Keyword(s):  
Steady State ◽  
Flow Field ◽  
Centrifugal Compressor ◽  
Aerodynamic Performance ◽  
Vaned Diffuser ◽  
Tip Leakage ◽  
Transonic Centrifugal Compressor ◽  
Compressor Performance ◽  
Unsteady Effects ◽  
Rans Analysis

Abstract This paper discusses the unsteady effects associated with the impeller/diffuser interaction on the internal flow field and aerodynamic performance of a centrifugal compressor. In centrifugal compressors with a vaned diffuser, the flow field is inherently unsteady due to the influence of interaction between the impeller and the diffuser, and the unsteadiness of the flow field can often have a great influence on the aerodynamic performance of the compressor. Especially in high-load compressors, it is considered that large unsteady effects are produced on the compressor performance with a strong flow unsteadiness. The unsteady effect on aerodynamic performance of the compressor has not been fully revealed yet, and sometimes the steady-state RANS simulation finds it difficult to predict the compressor performance. In this study, numerical simulations have been conducted for a transonic centrifugal compressor with a vaned diffuser. The unsteady effects were clarified by comparing the numerical results between a single-passage steady-state RANS analysis and a full-annulus unsteady RANS analysis. The comparison of simulation results showed the difference in entropy generation in the impeller. The impingement of diffuser shock wave with the impeller pressure surface brought about a cyclic increase in the blade loading near the impeller trailing edge. Accordingly, with increasing tip leakage flow rate, a second tip leakage vortex was newly generated in the aft part of the impeller, which resulted in additional unsteady loss generation inside the impeller.

Effect of Unsteadiness on the Performance of a Transonic Centrifugal Compressor Stage

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Isabelle Trébinjac ◽  
Pascale Kulisa ◽  
Nicolas Bulot ◽  
Nicolas Rochuon
Keyword(s):  
Shock Wave ◽  
Mass Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Wake Flow ◽  
Experimental Investigations ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Transonic Centrifugal Compressor

Numerical and experimental investigations were conducted in a transonic centrifugal compressor stage composed of a backswept splittered unshrouded impeller and a vaned diffuser. The characteristic curves of the compressor stage resulting from the unsteady simulations and the experiments show a good agreement over the whole operating range. On the contrary, the total pressure ratio resulting from the steady simulations is clearly overestimated. A detailed analysis of the flow field at design operating point led to identify the physical mechanisms involved in the blade row interaction that underlie the observed shift in performance. Attention was focused on the deformation in shape of the vane bow shock wave due its interaction with the jet and wake flow structure emerging from the impeller. An analytical model is proposed to quantify the time-averaged effects of the associated entropy increase. The model is based on the calculation of the losses across a shock wave at various inlet Mach numbers corresponding to the moving of the jet and wake flow in front of the shock wave. The model was applied to the compressor stage performance calculated with the steady simulations. The resulting curve of the overall pressure ratio as a function of the mass flow is clearly shifted toward the unsteady results. The model, in particular, enhances the prediction of the choked mass flow.

Numerical Investigation of Different Casing Treatments on Performance of a High Speed Centrifugal Compressor Stage

2011 ◽  
Author(s):  
Yan Ma ◽  
Guang Xi ◽  
Guangkuan Wu
Keyword(s):  
Numerical Investigation ◽  
Centrifugal Compressor ◽  
High Speed ◽  
The Other ◽  
Compressor Stage ◽  
Stall Margin ◽  
Casing Treatment ◽  
Centrifugal Compressor Stage ◽  
And Performance ◽  
Casing Treatments

In this paper, two different casing treatment devices—one adopting inlet recirculation at the shroud side of the impeller inlet and the other adopting circumferential casing grooves at the shroud side of the vaneless space, are designed for a high speed centrifugal compressor stage. The effects of different casing treatments to the flow range and performance of the centrifugal compressor stage are studied numerically. The results indicate that traditional inlet recirculation at impeller inlet does not extend the stall margin of the stage and the performance deteriorates due to the adding of the extra device. The study also shows that, when the location of the bleed slot moves downstream, the performance of the stage deteriorates due to the longer flow path. Moreover, the 2mm depth circumferential casing grooves extend the stall margin by about 12.05%. By contrast, the 6mm depth and 10mm depth grooves extend the stall margin by 3% and 2.4% respectively.

Sign in / Sign up

Export Citation Format

Share Document