Effects of the injection timing on knock and combustion characteristics in dual-fuel dual-injection engines

2020 ◽  
Vol 234 (10-11) ◽  
pp. 2578-2591
Author(s):  
Jie Li ◽  
Changwen Liu ◽  
Rui Kang ◽  
Lei Zhou ◽  
Haiqiao Wei
Keyword(s):  
Gasoline Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Intensity Increase ◽  
Spark Plug ◽  
Spark Timing

To utilize ethanol fuel in spark ignition engines more efficiently and flexibly, a new ethanol/gasoline dual-direct injection concept in gasoline engine is proposed. Therefore, based on the dual-fuel dual-direct injection system, the effects of different injection timings and two injector positions on the characteristics of combustion were studied comprehensively, and the effects of different octane numbers and temperature stratifications on knock and combustion were explored. The results show that as for Position A (ethanol injecting toward spark plug), with the delay of injection timing, knock tendency and its intensity increase initially and then decrease due to the comprehensive effect of ethanol evaporation and fuel stratification; on the contrary, for Position B (ethanol injecting toward end-gas region), retarding the injection timing of ethanol can effectively reduce the knock propensity. As for the engine performance, a dual-direct injection performs best, especially the retarded injection timing of ethanol for Position A. It can be found that with the delay of the fuel injection timing, the torque first increases and then decreases. The brake-specific fuel consumption decreases initially and then increases at maximum brake torque spark timing.

Automated Engine Calibration Optimization Using Online Extremum Seeking

2018 ◽  
Author(s):  
Ripudaman Singh ◽  
Andrew Mansfield ◽  
Margaret Wooldridge
Keyword(s):  
Control Parameter ◽  
Gasoline Engine ◽  
Fuel Injection ◽  
Engine Performance ◽  
Extremum Seeking ◽  
Injection System ◽  
Test Time ◽  
Injection Timing ◽  
Promising Alternative ◽  
Non Linear System

Emissions compliance during engine start-up conditions is a major obstacle for current automotive manufacturers across global markets. The challenges to meeting emissions targets are both due to increasingly stringent regulations and the difficulty in developing control strategies for a high degree-of-freedom and highly non-linear system. Online extremum-seeking (ES) methods offer a promising alternative to traditional optimization based on design-of-experiment based automotive calibration. With extremum-seeking methods, results from all prior experiments are used to intelligently and efficiently generate the next iteration of the control parameter(s). In this work, the applicability of the online extremum-seeking method is explored to optimize five performance variables (injection timing for two injection events, the injection fuel mass divided between the first and second injection events, air-fuel equivalence ratio and exhaust cam timing) to minimize brake specific fuel consumption while imposing different constraints on NOx emissions. The experiments were conducted using a production turbocharged four-cylinder gasoline engine with an advanced fuel injection system. The results show the utility of the ES strategy to quickly identify optimal control parameter combinations and the emissions and engine performance improvements during the calibration process. The results also demonstrate the dramatic benefit of the ES calibration strategy in terms of test time required.

Two-Stroke Engine with Fuel Semi-Direct Injection Using FAI System

2011 ◽  
Vol 130-134 ◽  
pp. 796-799
Author(s):  
Ming Ming Wu ◽  
Yan Xiang Yang ◽  
Da Guang Xi ◽  
Ping Zhang ◽  
Zhong Guo Jin
Keyword(s):  
Gasoline Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Injection Timing ◽  
Fuel System ◽  
Power Performance ◽  
Fuel Injection Timing ◽  
Injection Quantity ◽  
Stroke Engine

This paper presents the feasibility of semi-direct injection on a 50cm3, two-stroke motorcycle gasoline engine, which is applied FAI semi-direct injection fuel system. The structure and fuel injection system is improved based on the original carburetor engine and the FAI injector is easily installed. The results of laboratory and drive test show that, compared with the original carburetor fuel system, through optimization calibration of fuel injection timing and injection quantity can improve power performance and fuel economy.

Factors Affecting Performance of Dual Fuel Compression Ignition Engines

2013 ◽  
Vol 388 ◽  
pp. 217-222
Author(s):  
Mohamed Mustafa Ali ◽  
Sabir Mohamed Salih
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Compression Ignition ◽  
Factors Affecting

Compression Ignition Diesel Engine use Diesel as conventional fuel. This has proven to be the most economical source of prime mover in medium and heavy duty loads for both stationary and mobile applications. Performance enhancements have been implemented to optimize fuel consumption and increase thermal efficiency as well as lowering exhaust emissions on these engines. Recently dual fueling of Diesel engines has been found one of the means to achieve these goals. Different types of fuels are tried to displace some of the diesel fuel consumption. This study is made to identify the most favorable conditions for dual fuel mode of operation using Diesel as main fuel and Gasoline as a combustion improver. A single cylinder naturally aspirated air cooled 0.4 liter direct injection diesel engine is used. Diesel is injected by the normal fuel injection system, while Gasoline is carbureted with air using a simple single jet carburetor mounted at the air intake. The engine has been operated at constant speed of 3000 rpm and the load was varied. Different Gasoline to air mixture strengths investigated, and diesel injection timing is also varied. The optimum setting of the engine has been defined which increased the thermal efficiency, reduced the NOx % and HC%.

Particulate Matter Emission Comparison of Spark Ignition Direct Injection (SIDI) and Port Fuel Injection (PFI) Operation of a Boosted Gasoline Engine

2013 ◽  
Author(s):  
Jianye Su ◽  
Weiyang Lin ◽  
Jeff Sterniak ◽  
Min Xu ◽  
Stanislav V. Bohac
Keyword(s):  
Particulate Matter ◽  
Gasoline Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Spark Ignition ◽  
Specific Power ◽  
Injection Timing ◽  
Gasoline Engines ◽  
Port Fuel Injection ◽  
Spark Timing

Spark ignition direct injection (SIDI) gasoline engines, especially in downsized boosted engine platforms, are increasing their market share relative to port fuel injection (PFI) engines in U.S., European and Chinese vehicles due to better fuel economy by enabling higher compression ratios and higher specific power output. However, particulate matter (PM) emissions from engines are becoming a concern due to adverse human health and environment effects, and more stringent emission standards. To conduct a PM number and size comparison between SIDI and PFI systems, a 2.0 L boosted gasoline engine has been equipped and tested with both systems at different loads, air fuel ratios, spark timings, fuel pressures and injection timings for SIDI operation and loads, air fuel ratios and spark timings for PFI operation. Regardless of load, air fuel ratio, spark timing, fuel pressure, and injection timing, particle size distribution from SIDI and PFI is shown to be bimodal, exhibiting nucleation and accumulation mode particles. SIDI produces particle numbers that are an order of magnitude greater than PFI. Particle number can be reduced by retarding spark timing and operating the engine lean, both for SIDI and PFI operation. Increasing fuel injection pressure and optimizing injection timing with SIDI also reduces PM emissions. This study provides insight into the differences in PM emissions from boosted SIDI and PFI engines and an evaluation of PM reduction potential by varying engine operating parameters in boosted SIDI and PFI gasoline engines.

Particulate Matter Emission Comparison of Spark Ignition Direct Injection (SIDI) and Port Fuel Injection (PFI) Operation of a Boosted Gasoline Engine

2014 ◽  
Vol 136 (9) ◽  
Author(s):  
Jianye Su ◽  
Weiyang Lin ◽  
Jeff Sterniak ◽  
Min Xu ◽  
Stanislav V. Bohac
Keyword(s):  
Particulate Matter ◽  
Gasoline Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Spark Ignition ◽  
Specific Power ◽  
Injection Timing ◽  
Gasoline Engines ◽  
Port Fuel Injection ◽  
Spark Timing

Spark ignition direct injection (SIDI) gasoline engines, especially in downsized boosted engine platforms, are increasing their market share relative to port fuel injection (PFI) engines in U.S., European and Chinese vehicles due to better fuel economy by enabling higher compression ratios and higher specific power output. However, particulate matter (PM) emissions from engines are becoming a concern due to adverse human health and environment effects, and more stringent emission standards. To conduct a PM number and size comparison between SIDI and PFI systems, a 2.0 L boosted gasoline engine has been equipped and tested with both systems at different loads, air fuel ratios, spark timings, fuel pressures and injection timings for SIDI operation and loads, air fuel ratios and spark timings for PFI operation. Regardless of load, air fuel ratio, spark timing, fuel pressure, and injection timing, particle size distribution from SIDI and PFI is shown to be bimodal, exhibiting nucleation and accumulation mode particles. SIDI produces particle numbers that are an order of magnitude greater than PFI. Particle number can be reduced by retarding spark timing and operating the engine lean, both for SIDI and PFI operation. Increasing fuel injection pressure and optimizing injection timing with SIDI also reduces PM emissions. This study provides insight into the differences in PM emissions from boosted SIDI and PFI engines and an evaluation of PM reduction potential by varying engine operating parameters in boosted SIDI and PFI gasoline engines.

Effect of Optimization Criteria on Direct-Injection Homegeneous Charge Compression Ignition Gasoline Engine Performance and Emissions Using Fully Automated Experiments and Microgenetic Algorithms

2004 ◽  
Vol 126 (1) ◽  
pp. 167-177 ◽  
Author(s):  
M. Canakci ◽  
R. D. Reitz
Keyword(s):  
Gasoline Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Engine Performance ◽  
Function Optimization ◽  
Spray Angle ◽  
Injection Timing ◽  
Compression Ignition ◽  
Performance And Emissions ◽  
Engine Performance And Emissions

Homogeneous charge compression ignition (HCCI) is a new low-emission engine concept. Combustion under homogeneous, low equivalence ratio conditions results in modest temperature combustion products, containing very low concentrations of NOx and PM as well as providing high thermal efficiency. However, this combustion mode can produce higher HC and CO emissions than those of conventional engines. Control of the start of combustion timing is difficult with pre-mixed charge HCCI. Accordingly, in the present study charge preparation and combustion phasing control is achieved with direct injection. An electronically controlled Caterpillar single-cylinder oil test engine (SCOTE), originally designed for heavy-duty diesel applications, was converted to a direct-injection gasoline engine. The engine features an electronically controlled low-pressure direct injection-gasoline (DI-G) injector with a 60 deg spray angle that is capable of multiple injections. The use of double injection was explored for emission control, and the engine was optimized using fully automated experiments and a microgenetic algorithm optimization code. The variables changed during the optimization include the intake air temperature, start of injection timing, and the split injection parameters (percent mass of fuel in each injection, dwell between the pulses) using three different objective (merit) functions. The engine performance and emissions were determined at 700 rev/min with a constant fuel flow rate at 10 MPa fuel injection pressure. The results show the choice of merit or objective function (optimization goal) determines the engine performance, and that significant emission reductions can be achieved with optimal injection strategies. Merit function formulations are presented that minimized PM, HC, and NOx emissions, respectively.

The Research of Lean Combustion Characteristic of Compound Injection System of Direct Injection Engine

2014 ◽  
Vol 532 ◽  
pp. 362-366 ◽  
Author(s):  
Jiang Feng Mou ◽  
Rui Qing Chen ◽  
Yi Wei Lu
Keyword(s):  
Gasoline Engine ◽  
Direct Injection ◽  
Injection System ◽  
Intake Manifold ◽  
Combustion Characteristic ◽  
Injection Timing ◽  
Mixed Gas ◽  
Lean Burn ◽  
Direct Injection Engine ◽  
Lean Combustion

This paper studies the lean burn limit characteristic of the compound injection system of the direct-injection gasoline engine. The low pressure nozzle on the intake manifold can achieve quality homogeneous lean mixture, and the direct injection in the cylinder can realized the dense mixture gas near the spark plug. By adjusting the two injection timing and injection quantity, and a strong intake tumble flow with special shaped combustion chamber, it can produces the reverse tumble to form different hierarchical levels of mixed gas in the cylinder. Experimental results show: the compound combustion system to the original direct-injection engine lean burn limit raise 1.8-2.5 AFR unit.

scholarly journals Influence of the diesel pilot injector configuration on ethanol combustion and performance of a heavy-duty direct injection engine

2021 ◽  
pp. 146808742110012
Author(s):  
Nicola Giramondi ◽  
Anders Jäger ◽  
Daniel Norling ◽  
Anders Christiansen Erlandsson
Keyword(s):  
Direct Injection ◽  
Engine Performance ◽  
High Load ◽  
Operating Conditions ◽  
Injection System ◽  
Injection Timing ◽  
Diesel Combustion ◽  
Heavy Duty ◽  
Pure Ethanol ◽  
Ethanol Combustion

Thanks to its properties and production pathways, ethanol represents a valuable alternative to fossil fuels, with potential benefits in terms of CO2, NOx, and soot emission reduction. The resistance to autoignition of ethanol necessitates an ignition trigger in compression-ignition engines for heavy-duty applications, which in the current study is a diesel pilot injection. The simultaneous direct injection of pure ethanol as main fuel and diesel as pilot fuel through separate injectors is experimentally investigated in a heavy-duty single cylinder engine at a low and a high load point. The influence of the nozzle hole number and size of the diesel pilot injector on ethanol combustion and engine performance is evaluated based on an injection timing sweep using three diesel injector configurations. The tested configurations have the same geometric total nozzle area for one, two and four diesel sprays. The relative amount of ethanol injected is swept between 78 – 89% and 91 – 98% on an energy basis at low and high load, respectively. The results show that mixing-controlled combustion of ethanol is achieved with all tested diesel injector configurations and that the maximum combustion efficiency and variability levels are in line with conventional diesel combustion. The one-spray diesel injector is the most robust trigger for ethanol ignition, as it allows to limit combustion variability and to achieve higher combustion efficiencies compared to the other diesel injector configurations. However, the two- and four-spray diesel injectors lead to higher indicated efficiency levels. The observed difference in the ethanol ignition dynamics is evaluated and compared to conventional diesel combustion. The study broadens the knowledge on ethanol mixing-controlled combustion in heavy-duty engines at various operating conditions, providing the insight necessary for the optimization of the ethanol-diesel dual-injection system.

scholarly journals Research on Fuel Efficiency and Emissions of Converted Diesel Engine with Conventional Fuel Injection System for Operation on Natural Gas

Energies ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 2413 ◽  
Author(s):  
Lebedevas ◽  
Pukalskas ◽  
Daukšys ◽  
Rimkus ◽  
Melaika ◽  
...  
Keyword(s):  
Energy Efficiency ◽  
Natural Gas ◽  
Fuel Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Fuel Injection System ◽  
Significant Deterioration ◽  
Engine Operation ◽  
Conventional Fuel

This paper presents a study on the energy efficiency and emissions of a converted high-revolution bore 79.5 mm/stroke 95 mm engine with a conventional fuel injection system for operation with dual fuel feed: diesel (D) and natural gas (NG). The part of NG energy increase in the dual fuel is related to a significant deterioration in energy efficiency (ηi), particularly when engine operation is in low load modes and was determined to be below 40% of maximum continuous rating. The effectiveness of the D injection timing optimisation was established in high engine load modes within the range of a co-combustion ratio of NG ≤ 0.4: with an increase in ηi, compared to D, the emissions of NOx+ HC decreased by 15% to 25%, while those of CO2 decreased by 8% to 16%; the six-fold CO emission increase, up to 6 g/kWh, was unregulated. By referencing the indicated process characteristics of the established NG phase elongation in the expansion stroke, the combustion time increase as well as the associated decrease in the cylinder excess air ratio (α) are possible reasons for the increase in the incomplete combustion product emission.

scholarly journals Predicting Cycle-to-Cycle Variation With Concurrent Cycles in a Gasoline Direct Injected Engine With Large Eddy Simulations

2018 ◽  
Author(s):  
Daniel Probst ◽  
Sameera Wijeyakulasuriya ◽  
Eric Pomraning ◽  
Janardhan Kodavasal ◽  
Riccardo Scarcelli ◽  
...  
Keyword(s):  
Gasoline Engine ◽  
Direct Injection ◽  
Engine Performance ◽  
Turnaround Time ◽  
Operating Conditions ◽  
Gasoline Direct Injection ◽  
Cycle Variation ◽  
Spark Timing ◽  
Large Eddy ◽  
Operating Points

High cycle-to-cycle variation (CCV) is detrimental to engine performance, as it leads to poor combustion and high noise and vibration. In this work, CCV in a gasoline engine is studied using large eddy simulation (LES). The engine chosen as the basis of this work is a single-cylinder gasoline direct injection (GDI) research engine. Two stoichiometric part-load engine operating points (6 BMEP, 2000 RPM) were evaluated: a non-dilute (0% EGR) case and a dilute (18% EGR) case. The experimental data for both operating conditions had 500 cycles. The measured CCV in IMEP was 1.40% for the non-dilute case and 7.78% for the dilute case. To estimate CCV from simulation, perturbed concurrent cycles of engine simulations were compared to consecutively obtained engine cycles. The motivation behind this is that running consecutive cycles to estimate CCV is quite time-consuming. For example, running 100 consecutive cycles requires 2–3 months (on a typical cluster), however, by running concurrently one can potentially run all 100 cycles at the same time and reduce the overall turnaround time for 100 cycles to the time taken for a single cycle (2 days). The goal of this paper is to statistically determine if concurrent cycles, with a perturbation applied to each individual cycle at the start, can be representative of consecutively obtained cycles and accurately estimate CCV. 100 cycles were run for each case to obtain statistically valid results. The concurrent cycles began at different timings before the combustion event, with the motivation to identify the closest time before spark to minimize the run time. Only a single combustion cycle was run for each concurrent case. The calculated standard deviation of peak pressure and coefficient of variance (COV) of indicated mean effective pressure (IMEP) were compared between the consecutive and concurrent methods to quantify CCV. It was found that the concurrent method could be used to predict CCV with either a velocity or numerical perturbation. A large and small velocity perturbation were compared and both produced correct predictions, implying that the type of perturbation is not important to yield a valid realization. Starting the simulation too close to the combustion event, at intake valve close (IVC) or at spark timing, under-predicted the CCV. When concurrent simulations were initiated during or before the intake even, at start of injection (SOI) or earlier, distinct and valid realizations were obtained to accurately predict CCV for both operating points. By simulating CCV with concurrent cycles, the required wall clock time can be reduced from 2–3 months to 1–2 days. Additionally, the required core-hours can be reduced up to 41%, since only a portion of each cycle needs to be simulated.

Sign in / Sign up

Export Citation Format

Share Document