Numerical investigation of blowing ratio, density ratio and axial position of film holes on the vane endwall film cooling effectiveness with upstream step

2021 ◽  
pp. 095441002110165
Author(s):  
Qingzong Xu ◽  
Qiang Du ◽  
Pei Wang ◽  
Xiangtao Xiao ◽  
Jun Liu
Keyword(s):  
Secondary Flow ◽  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Density Ratio ◽  
Total Pressure Loss ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Endwall Film Cooling

The aerothermal performance of interrupted slot and film holes was numerically investigated. Previous study indicates that the interrupted slot performs better compared to the conventional slot. In the meanwhile, the step formed along with the interrupted slot affects the film cooling characteristics. In this article, a row of film holes is arranged downstream of the step, and the mass flow rate for the interrupted slot is constant at 1%. Blowing ratio (BR) from 0.5 to 1.5 and density ratio from 1 to 2 were studied for the film holes. Endwall film cooling effectiveness distribution indicates that film cooling is easily affected by the secondary flow inside passage and the upstream step. Coolant traces are split into two parts due to the effects of step vortex and transverse flow. For different density ratios, increasing BR shows a different trend of film cooling effectiveness due to the variation of coolant momentum. The coolant jet is easily affected by the secondary flow when its momentum is low, but tends to liftoff when its momentum is too high. As a result, it is better to position the film holes far away from the upstream step. The total pressure loss coefficient distribution at the passage exit indicates that the coolant injection increases the total pressure loss. But density ratio has smaller effect on the loss variation. Besides, two axial positions of cooling holes were studied to improve the endwall cooling performance. Without the effect of step vortex, the film effectiveness of cooling holes is improved.

Blowing Ratio Effect on Film Cooling Performance for a Row Holes Installed in Different Trench Configurations

2020 ◽  
Vol 28 ◽  
pp. 65-75
Author(s):  
Khadidja Boualem ◽  
Abbes Azzi
Keyword(s):  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Pressure Loss Coefficient ◽  
Blowing Ratio ◽  
Ansys Cfx ◽  
Cooling Hole

In the present study, a numerical analysis was performed to evaluate the performance of cooling hole embedded in different trenched designs (triangular trench, semi-cylindrical trench and corrugated trench) in improving the film cooling efficiency over a flat plate. These concepts are compared to the rectangular trenched and the traditional cylindrical hole. The commercial software ANSYS CFX 18 was used to conduct a series of required numerical calculations. The centerline and laterally averaged film cooling effectiveness and total pressure loss coefficient for the five cases are analyzed at three blowing ratios, M=0.5, M=1.0 and M=1.5. Results show a uniform coverage is obtained by hole installed in trench. The main result obtained in this paper that the cooling hole with corrugated trench enhance the film cooling effectiveness with less total pressure loss. The main result of this study reveals that the jet installed in the trenches yield a better film cooling effectiveness especially at higher blowing ratios (M≥1).

Turbine Blade Platform Film Cooling With Typical Stator-Rotor Purge Flow and Discrete-Hole Film Cooling

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Zhihong Gao ◽  
Diganta Narzary ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Purge Flow ◽  
Cylindrical Holes ◽  
Film Cooling Holes

This paper is focused on the effect of film-hole configurations on platform film cooling. The platform is cooled by purge flow from a simulated stator-rotor seal combined with discrete-hole film cooling within the blade passage. The cylindrical holes and laidback fan-shaped holes are assessed in terms of film-cooling effectiveness and total pressure loss. Lined up with the freestream streamwise direction, the film holes are arranged on the platform with two different layouts. In one layout, the film-cooling holes are divided into two rows and more concentrated on the pressure side of the passage. In the other layout, the film-cooling holes are divided into four rows and loosely distributed on the platform. Four film-cooling hole configurations are investigated totally. Testing was done in a five-blade cascade with medium high Mach number condition (0.27 and 0.44 at the inlet and the exit, respectively). The detailed film-cooling effectiveness distributions on the platform were obtained using pressure sensitive paint technique. Results show that the combined cooling scheme (slot purge flow cooling combined with discrete-hole film cooling) is able to provide full film coverage on the platform. The shaped holes present higher film-cooling effectiveness and wider film coverage than the cylindrical holes, particularly at higher blowing ratios. The hole layout affects the local film-cooling effectiveness. The shaped holes also show the advantage over the cylindrical holes with lower total pressure loss.

Turbine Blade Platform Film Cooling With Typical Stator-Rotor Purge Flow and Discrete-Hole Film Cooling

2008 ◽  
Author(s):  
Zhihong Gao ◽  
Diganta Narzary ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Purge Flow ◽  
Cylindrical Holes ◽  
Film Cooling Holes

This paper is focused on the effect of film hole configurations on platform film cooling. The platform is cooled by purge flow from a simulated stator-rotor seal combined with discrete-hole film cooling within the blade passage. The cylindrical holes and laidback fan-shaped holes are assessed in terms of film cooling effectiveness and total pressure loss. Lined up with the freestream streamwise direction, the film holes are arranged on the platform with two different layouts. In one layout, the film cooling holes are divided into two rows and more concentrated on the pressure side of the passage. In the other layout, the film cooling holes are divided into four rows and loosely distributed on the platform. Four film cooling hole configurations are investigated totally. Testing was done in a five-blade cascade with medium high Mach number condition (0.27 and 0.44 at the inlet and the exit, respectively). The detailed film cooling effectiveness distributions on the platform was obtained using pressure sensitive paint (PSP) technique. Results show that the combined cooling scheme (slot purge flow cooling combined with discrete hole film cooling) is able to provide full film coverage on the platform. The shaped holes present higher film cooling effectiveness and wider film coverage than the cylindrical holes, particularly at higher blowing ratios. The hole layout affects the local film cooling effectiveness. The shaped holes also show the advantage over the cylindrical holes with lower total pressure loss.

Effect of Non-Axisymmetric Endwall Profiling on Heat Transfer and Film Cooling Effectiveness of a Transonic Rotor Blade

2020 ◽  
Vol 142 (5) ◽  
Author(s):  
Jinjin Li ◽  
Xin Yan ◽  
Kun He
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Rotor Blade ◽  
Stanton Number ◽  
Total Pressure Loss ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Transonic Rotor

Abstract Effects of non-axisymmetric endwall profiling on total pressure loss, heat transfer, and film cooling effectiveness of a transonic rotor blade were numerically investigated. The numerical methods, including the turbulence model and grid sensitivity, were validated with the existing experimental data. To reduce the thermal load on endwall, non-axisymmetric endwall profiling near leading edge and at pressure-side corner area was performed with a range of contour amplitudes. Heat transfer and flow fields near the profiled endwalls were analyzed and also compared with the plain endwall configuration. On the profiled endwall, three kinds of cooling holes, i.e., cylindrical holes, rounded-rectangular holes, and elliptical holes, were arranged, and film cooling effect was investigated at three blowing ratios. Results indicate that, with endwall profiling, the area-averaged Stanton number on endwall is reduced by 7.71% and total pressure loss in cascade is reduced by 11.07%. Among three kinds of cooling holes, the arrangement of the elliptical hole performs the best film cooling effect on the profiled endwall. Compared with the plain endwall, non-axisymmetric endwall with elliptical cooling holes improves film cooling coverage by 10.87%, reduces the Stanton number by 8.88%, and increases the net heat flux reduction performance by 4% at M = 0.7.

Effect of Non-Axisymmetric Endwall Profiling on Heat Transfer and Film Cooling Effectiveness of a Transonic Rotor Blade

2019 ◽  
Author(s):  
Jinjin Li ◽  
Xin Yan ◽  
Kun He
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Rotor Blade ◽  
Stanton Number ◽  
Total Pressure Loss ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Transonic Rotor

Abstract Effects of non-axisymmetric endwall profiling on total pressure loss, heat transfer and film cooling effectiveness of a transonic rotor blade were numerically investigated. The numerical methods, including the turbulence model and grid sensitivity, were validated with the existing experimental data. To reduce thermal load on endwall, non-axisymmetric endwall profiling near leading edge and at pressure-side corner area were performed with a range of contour amplitudes. Heat transfer and flow fields near the profiled endwalls were analyzed and also compared to the plain endwall configuration. On the profiled endwall, three kinds of cooling-holes, i.e. cylindrical holes, rounded-rectangular holes and elliptical holes, were arranged, and film cooling effect was investigated at three blowing ratios. Results indicate that, with endwall profiling, the area-averaged Stanton number on endwall is reduced by 7.71% and total pressure loss in cascade is reduced by 11.07%. Among three kinds of cooling holes, arrangement of elliptical hole performs the best film cooling effect on profiled endwall. Compared with plain endwall, non-axisymmetric endwall with elliptical cooling holes improves film cooling coverage by 10.87%, reduces the Stanton number by 8.88% and increases the net heat flux reduction performance by 4% at M = 0.7.

Investigations of Heat Transfer and Film Cooling Effect on a Worn Squealer Tip

2020 ◽  
Author(s):  
Mingliang Ye ◽  
Xin Yan
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Wear Depth ◽  
Original Design ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cavity Floor

Abstract Wear damage commonly occurs in modern gas turbine rotor blade tip due to relative movements and expansions between rotating and stationary parts. Tip wear has a significant impact on the aerodynamic, heat transfer and cooling performance of rotor blades, thus threatening the economy and safety of whole gas turbine system. Based on a simple linear wear model, this paper numerically investigates the aerodynamic, heat transfer and film cooling performance of a worn squealer tip with three starting-locations of wear (sl = 25%Cax, 50%Cax and 75%Cax) and five wear-depths (wd = 0.82%, 1.64%, 2.46%, 3.28% and 4.10%). Firstly, based on the existing experimental data, numerical methods and grid independence are examined carefully. Then, three dimensional flow fields, total pressure loss distributions, heat transfer coefficients and film cooling effectiveness in worn squealer tip region are computed, which are compared with the original design case. The results show that, with the increase of wear depth and the movement of wear starting-location to the leading edge, the scale and intensity of cavity vortex are increased, which results in the extended high heat transfer area on cavity floor near the leading edge. Wear makes more coolant flow out of the cavity, and reduces the area-averaged film cooling effectiveness at the bottom of cavity, but increases the film cooling effectiveness on pressure-side rim. The increase of wear depth makes more flow leak through the tip gap, thus increasing the scale and intensity of leakage vortex and further increasing the total pressure loss in the tip gap. Compared with the original design case, as the wear depth is increased from 0.82% to 4.10%, the mass-averaged total pressure loss in cascade is increased by 0.3–6.7%, the area-averaged heat transfer coefficient on cavity floor is increased by 1.7–29.1% while on squealer rim it is decreased by 3.1–26.3%, and the area-averaged film cooling effectiveness on cavity floor is decreased by 0.035 at most while on squealer rim it is increased by 0.064 at most.

scholarly journals Prediction of Vane Surface Film Cooling Effectiveness Using Compressible Navier-Stokes Procedure and k-ε Turbulence Model With Wall Function

1995 ◽  
Author(s):  
Yoshitaka Fukuyama ◽  
Fumio Otomo ◽  
Minoru Sato ◽  
Yuichi Kobayashi ◽  
Hiroyuki Matsuzaki
Keyword(s):  
Turbulence Model ◽  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Navier Stokes ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Near Wall

A numerical prediction has been performed on the film cooling effectiveness and the total pressure loss of the actual turbine vane geometry. The Navier-Stokes code used in this study is an implicit, cell-centered, finite volume code with k-ε turbulence models. The convection term was stabilized by the variable order up-winding scheme. The film cooling injection has been simulated by adding the prescribed flux terms at the vane surface. The k and ε near wall distribution functions were developed based on the experimental and the DNS results in the literature. The wall functions for k and ε can be used with the selected low Reynolds number version of k-ε turbulence model irrespective of the distance between the wall and the first grid point. This combination would result in lower computational costs, since, near wall grid number can be reduced significantly. Based on the study, the Navier-Stokes predictions were performed on the actual turbine vane geometry. Also, the comparisons were made with the experimental total pressure loss distribution behind the vane row and the mid-span film-cooling effectiveness distribution for single and double row injection cases.

Influence of Coolant Density on Turbine Platform Film-Cooling With Stator–Rotor Purge Flow and Compound-Angle Holes

2014 ◽  
Vol 6 (4) ◽  
Author(s):  
Kevin Liu ◽  
Shang-Feng Yang ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Fundamental Parameters ◽  
Blowing Ratio ◽  
Purge Flow ◽  
Cylindrical Holes ◽  
Exit Mach Number ◽  
Compound Angle

A detailed parametric study of film-cooling effectiveness was carried out on a turbine blade platform. The platform was cooled by purge flow from a simulated stator–rotor seal combined with discrete hole film-cooling. The cylindrical holes and laidback fan-shaped holes were accessed in terms of film-cooling effectiveness. This paper focuses on the effect of coolant-to-mainstream density ratio on platform film-cooling (DR = 1 to 2). Other fundamental parameters were also examined in this study—a fixed purge flow of 0.5%, three discrete-hole film-cooling blowing ratios between 1.0 and 2.0, and two freestream turbulence intensities of 4.2% and 10.5%. Experiments were done in a five-blade linear cascade with inlet and exit Mach number of 0.27 and 0.44, respectively. Reynolds number of the mainstream flow was 750,000 and was based on the exit velocity and chord length of the blade. The measurement technique adopted was the conduction-free pressure sensitive paint (PSP) technique. Results indicated that with the same density ratio, shaped holes present higher film-cooling effectiveness and wider film coverage than the cylindrical holes, particularly at higher blowing ratios. The optimum blowing ratio of 1.5 exists for the cylindrical holes, whereas the effectiveness for the shaped holes increases with an increase of blowing ratio. Results also indicate that the platform film-cooling effectiveness increases with density ratio but decreases with turbulence intensity.

Numerical Investigation of Effects of Blockage, Inclination Angle, and Hole-Size on Film Cooling Effectiveness at Concave Surface

2021 ◽  
Vol 143 (2) ◽  
Author(s):  
Fu-qiang Wang ◽  
Jian Pu ◽  
Jian-hua Wang ◽  
Wei-dong Xia
Keyword(s):  
Film Cooling ◽  
Pressure Loss ◽  
Numerical Study ◽  
Density Ratio ◽  
Concave Surface ◽  
Blockage Ratio ◽  
Coverage Area ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Injection Angle

Abstract Film-hole can be often blocked by thermal-barrier coatings (TBCs) spraying, resulting in the variations of aerodynamic and thermal performances of film cooling. In this study, a numerical study of the blockage effect on the film cooling effectiveness of inclined cylindrical-holes was carried out on a concave surface to simulate the airfoil pressure side. Three typical blowing ratios (BRs) of 0.5, 1.0, and 1.5 were chosen at an engine-similar density ratio (DR) of 2.0. Two common inclination angles of 30 deg and 45 deg were designed. The blockage ratios were adjusted from 0 to 20%. The results indicated the blockage could enhance the penetration of film cooling flow to the mainstream. Thus, the averaged effectiveness and coolant coverage area were reduced. Moreover, the pressure loss inside of the hole was increased. With the increase of BR, the decrement of film cooling effectiveness caused by blockage rapidly increased. At BR = 1.5, the decrement could be acquired up to 70% for a blockage ratio of 20%. The decrement of film cooling effectiveness caused by blockage was nearly nonsensitive to the injection angle; however, the larger angle could generate the higher increment of pressure loss caused by blockage. A new design method for the couple scheme of film cooling and TBC was proposed, i.e., increasing the inlet diameter according to the blockage ratio before TBC spraying. In comparison with the original unblocked-hole, the enlarged blocked-hole not only kept the nearly same area-averaged effectiveness but also reduced slightly the pressure loss inside of the hole. Unfortunately, application of enlarged blocked-hole at large BR could lead to a more obvious reduction of effectiveness near hole-exit, in comparison with the original common-hole.

Sign in / Sign up

Export Citation Format

Share Document