scholarly journals A Proposed Fabrication Method of Novel PCL-GEL-HAp Nanocomposite Scaffolds for Bone Tissue Engineering Applications

2010 ◽  
Vol 19 (4) ◽  
pp. 096369351001900 ◽  
Author(s):  
A. Hamlekhan ◽  
M. Mozafari ◽  
N. Nezafati ◽  
M. Azami ◽  
H. Hadipour
Keyword(s):  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Mechanical Test ◽  
Fibroblast Cell ◽  
Mouse Fibroblast ◽  
Fabrication Method ◽  
Engineering Applications ◽  
Poly Caprolactone

In this study, poly(∊-caprolactone) (PCL), gelatin (GEL) and nanocrystalline hydroxyapatite (HAp) was applied to fabricate novel PCL-GEL-HAp nanaocomposite scaffolds through a new fabrication method. With the aim of finding the best fabrication method, after testing different methods and solvents, the best method and solvents were found, and the nanocomposites were prepared through layer solvent casting combined with freeze-drying. Acetone and distillated water were used as the PCL and GEL solvents, respectively. The mechanical test showed that the increasing of the PCL weight through the scaffolds caused the improvement of the final nanocomposite mechanical behavior due to the increasing of the ultimate stress, stiffness and elastic modulus (8 MPa for 0% wt PCL to 23.5 MPa for 50% wt PCL). The biomineralization investigation of the scaffolds revealed the formation of bone-like apatite layers after immersion in simulated body fluid (SBF). In addition, the in vitro cytotoxity of the scaffolds using L929 mouse fibroblast cell line (ATCC) indicated no sign of toxicity. These results indicated that the fabricated scaffold possesses the prerequisites for bone tissue engineering applications.

scholarly journals In vitro study of novel microparticle based silk fibroin scaffold with osteoblast-like cells for load-bearing osteo-regenerative applications

RSC Advances ◽  
2017 ◽  
Vol 7 (43) ◽  
pp. 26551-26558 ◽  
Author(s):  
Nimisha Parekh ◽  
Chandni Hushye ◽  
Saniya Warunkar ◽  
Sayam Sen Gupta ◽  
Anuya Nisal
Keyword(s):  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Silk Fibroin ◽  
In Vitro Study ◽  
Vitro Study ◽  
Engineering Applications ◽  
Load Bearing ◽  
Silk Fibroin Scaffold

Silk Fibroin microparticle scaffolds show promise in bone tissue engineering applications.

scholarly journals In vitro and in vivo Biocompatibility of Alginate Dialdehyde/Gelatin Hydrogels with and without Nanoscaled Bioactive Glass for Bone Tissue Engineering Applications

Materials ◽  
2014 ◽  
Vol 7 (3) ◽  
pp. 1957-1974 ◽  
Author(s):  
Ulrike Rottensteiner ◽  
Bapi Sarker ◽  
Dominik Heusinger ◽  
Diana Dafinova ◽  
Subha Rath ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Bioactive Glass ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Engineering Applications

scholarly journals Plant-derived Cellulose Scaffolds for Bone Tissue Engineering

2020 ◽  
Author(s):  
Maxime Leblanc Latour ◽  
Maryam Tarar ◽  
Ryan J. Hickey ◽  
Charles M. Cuerrier ◽  
Isabelle Catelas ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Pore Size ◽  
Bone Tissue ◽  
Structural Features ◽  
Osteogenic Potential ◽  
Engineering Applications ◽  
Alizarin Red

AbstractPlant-derived cellulose biomaterials have recently been utilized in several tissue engineering applications. Naturally-derived cellulose scaffolds have been shown to be highly biocompatible in vivo, possess structural features of relevance to several tissues, as well as support mammalian cell invasion and proliferation. Recent work utilizing decellularized apple hypanthium tissue has shown that it possesses a pore size and properties similar to trabecular bone. In the present study, we examined the potential of apple-derived cellulose scaffolds for bone tissue engineering (BTE). Confocal microscopy revealed that the scaffolds had a suitable pore size for BTE applications. To analyze their in vitro mineralization potential, MC3T3-E1 pre-osteoblasts were seeded in either bare cellulose scaffolds or in composite scaffolds composed of cellulose and collagen I. Following chemically-induced differentiation, scaffolds were mechanically tested and evaluated for mineralization. The Young’s modulus of both types of scaffolds significantly increased after cell differentiation. Alkaline phosphatase and Alizarin Red staining further highlighted the osteogenic potential of the scaffolds. Histological sectioning of the constructs revealed complete invasion by the cells and mineralization throughout the entire constructs. Finally, scanning electron microscopy demonstrated the presence of mineral aggregates deposited on the scaffolds after differentiation, and energy-dispersive spectroscopy confirmed the presence of phosphate and calcium. In summary, our results indicate that plant-derived cellulose is a promising scaffold candidate for bone tissue engineering applications.

scholarly journals Development of an angiogenesis-promoting microvesicle-alginate-polycaprolactone composite graft for bone tissue engineering applications

PeerJ ◽  
2016 ◽  
Vol 4 ◽  
pp. e2040 ◽  
Author(s):  
Hui Xie ◽  
Zhenxing Wang ◽  
Liming Zhang ◽  
Qian Lei ◽  
Aiqi Zhao ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Regeneration ◽  
Bone Tissue ◽  
Umbilical Vein ◽  
Composite Graft ◽  
Electron Microscopic ◽  
Engineering Applications

One of the major challenges of bone tissue engineering applications is to construct a fully vascularized implant that can adapt to hypoxic environments in vivo. The incorporation of proangiogenic factors into scaffolds is a widely accepted method of achieving this goal. Recently, the proangiogenic potential of mesenchymal stem cell-derived microvesicles (MSC-MVs) has been confirmed in several studies. In the present study, we incorporated MSC-MVs into alginate-polycaprolactone (PCL) constructs that had previously been developed for bone tissue engineering applications, with the aim of promoting angiogenesis and bone regeneration. MSC-MVs were first isolated from the supernatant of rat bone marrow-derived MSCs and characterized by scanning electron microscopic, confocal microscopic, and flow cytometric analyses. The proangiogenic potential of MSC-MVs was demonstrated by the stimulation of tube formation of human umbilical vein endothelial cellsin vitro. MSC-MVs and osteodifferentiated MSCs were then encapsulated with alginate and seeded onto porous three-dimensional printed PCL scaffolds. When combined with osteodifferentiated MSCs, the MV-alginate-PCL constructs enhanced vessel formation and tissue-engineered bone regeneration in a nude mouse subcutaneous bone formation model, as demonstrated by micro-computed tomographic, histological, and immunohistochemical analyses. This MV-alginate-PCL construct may offer a novel, proangiogenic, and cost-effective option for bone tissue engineering.

Microwave synthesis, characterization, bioactivity and in vitro biocompatibility of zeolite–hydroxyapatite (Zeo–HA) composite for bone tissue engineering applications

2014 ◽  
Vol 40 (10) ◽  
pp. 16091-16097 ◽  
Author(s):  
Nida Iqbal ◽  
Mohammed Rafiq Abdul Kadir ◽  
Nasrul Humaimi Bin Mahmood ◽  
Mohammad Faiz Mohammad Yusoff ◽  
Jamal Akhter Siddique ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Microwave Synthesis ◽  
Engineering Applications ◽  
In Vitro Biocompatibility
Sign in / Sign up

Export Citation Format

Share Document