Behaviour of cold-formed steel built-up I-section columns composed of four U-profiles

2018 ◽  
Vol 22 (3) ◽  
pp. 613-625 ◽  
Author(s):  
M Anbarasu ◽  
M Venkatesan
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Ultimate Strength ◽  
Element Model ◽  
Cross Sectional ◽  
Direct Strength Method ◽  
The North ◽  
Compression Members ◽  
Cross Sectional Dimension ◽  
Cold Formed Steel

This work reports numerical results concerning the cold-formed steel built-up I-section columns composed of four U-profiles under axial compression. A finite element model is developed by using the software program ABAQUS. The developed model includes geometric, material nonlinearities and geometric imperfections. The finite element model was verified against the experimental results reported in the cold-formed steel built-up open section columns. In the parametric study, the sections are analysed with several cross-sectional dimension ratios and lengths, in order to assess their influence on the buckling behaviour and ultimate strength of cold-formed steel built-up I-section columns. After presenting and discussing the numerical parametric results, the article shows that the current direct strength method in the North American Specification for cold-formed steel compression members design curve fails to predict adequately the ultimate strength of some of the columns analysed and addresses the modification proposed on current direct strength method curves, providing improved predictions of all the numerical ultimate strength available. The proposed method is also assessed by reliability analysis.

Effective design width for perforated cold-formed steel compression members

1998 ◽  
Vol 25 (2) ◽  
pp. 319-330 ◽  
Author(s):  
Nabil Abdel-Rahman ◽  
K S Sivakumaran
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Ultimate Strength ◽  
Experimental Studies ◽  
Element Model ◽  
Short Columns ◽  
Compression Members ◽  
Assumed Strain ◽  
Cold Formed Steel ◽  
Effective Design

Perforations are often provided in the web and (or) flange plates of beams and columns of cold-formed steel (CFS) structural members in order to facilitate duct work, piping, and bridging. This paper is concerned with the establishment of effective design width equations for the determination of the ultimate strength of such perforated members in compression. A proven finite element model has been used to study the effects of perforation parameters on the ultimate strength of perforated members. The finite element model consists of short columns of lipped channel CFS sections, discretized using nonlinear "assumed strain" shell finite elements, and utilising experimental-based material properties models. The parametric study covers web slenderness values between 31 and 194, perforation width to web width ratios up to 0.6, and perforation height to perforation width ratios up to 3.0. Effective design width equations for plates having square perforations and elongated perforations were developed. The efficiency and accuracy of these two equations in predicting the ultimate strength of perforated CFS compression members have been verified through a comparison with the ultimate load results of several experimental studies from the literature.Key words: cold-formed steel, compressive loads, local buckling, perforations, finite element analysis, experimental, post-buckling strength, ultimate strength, effective width, design.

scholarly journals Experimental and Numerical Investigations of Ultimate Strength of Imperfect Stiffened Plates of Different Slenderness

2020 ◽  
Vol 27 (4) ◽  
pp. 120-129
Author(s):  
Krzysztof Woloszyk ◽  
Yordan Garbatov ◽  
Jakub Kowalski ◽  
Leszek Samson
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Ultimate Strength ◽  
Compressive Force ◽  
Initial Imperfection ◽  
Element Model ◽  
Stiffened Plates ◽  
Structural Behaviour ◽  
Middle Cross Section ◽  
Geometrical Imperfections

AbstractThe objective of this study is to analyse the behaviour of compressed stiffened plates of different slenderness using experimental and numerical methods. The presented results are part of a long-term project to investigate the ultimate strength of geometrically imperfect structures subjected to different degradation phenomena, including corrosion degradation and locked cracks. Several specimens were subjected to a uniaxial compressive force, and the most important quantities related to the structural behaviour were captured and analysed. A finite element model, accounting for material and geometrical nonlinearities and initial geometrical imperfections, was developed using the commercial software ANSYS. The residual welding-induced stresses were measured in the middle cross-section for two specimens. The initial imperfection was identified by employing a close-range photogrammetry approach. It was concluded that the numerical analyses, based on the finite element model, predict the ultimate strength of stiffened plates accurately, although some deviations were also observed. The detailed analysis with the indication of possible uncertainty is presented, and several conclusions are derived.

Finite element model of a novel short stemmed total hip arthroplasty implant developed from cross sectional CT scans

2013 ◽  
Vol 21 (5) ◽  
pp. 493-500 ◽  
Author(s):  
Matthias Lerch ◽  
Nelly Weigel ◽  
Henning Windhagen ◽  
Max Ettinger ◽  
Fritz Thorey ◽  
...  
Keyword(s):  
Finite Element ◽  
Total Hip Arthroplasty ◽  
Finite Element Model ◽  
Hip Arthroplasty ◽  
Element Model ◽  
Ct Scans ◽  
Cross Sectional ◽  
Total Hip

NUMERICAL ANALYSIS OF AXIALLY LOADED COLD-FORMED STEEL BUILT-UP BOX SECTION

2016 ◽  
Vol 3 (2) ◽  
Author(s):  
T.C.H. Ting ◽  
H.H. Lau ◽  
M.S. Joo
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Construction Industry ◽  
Element Model ◽  
Design Code ◽  
Design Guideline ◽  
Box Section ◽  
Current Design ◽  
Cold Formed Steel ◽  
The Finite Element Model

Built up box section is a doubly symmetrical section in which two C-channel connected at the flange using self-drilling screw. They are generally used in the construction industry to obtain higher rigidity, when a single section is not sufficient. Despite being widely used in the construction industry, there are limited studies on built-up box section. Moreover, the current design code does not provide clear design guideline for the calculation of built-up box section. Therefore, research on the built-up box section is important. This paper presents a finite element model to predict the compressive strength and simulate the behavior of cold-formed steel built-up box section. The finite element model was developed using ABAQUS CAE/6.14. Comparison of the finite element and experimental results showed good correlation. The model well predicted the behavior of the built-up box column.

Ultimate strength of columns laterally braced by girt–diaphragm systems

1989 ◽  
Vol 16 (3) ◽  
pp. 227-238 ◽  
Author(s):  
Bruno Massicotte ◽  
Denis Beaulieu ◽  
André Picard
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Ultimate Strength ◽  
Parametric Study ◽  
Design Method ◽  
Element Model ◽  
Structural System ◽  
Industrial Buildings ◽  
Stabilizing Effect ◽  
Stability Statistics

This paper deals with the stabilizing effect of girts and cladding on columns in light industrial buildings. The construction aspects of such systems are briefly reviewed and a description of their behavior is presented. Solutions available to determine column strength in column–girt–diaphragm systems are reviewed. The use of a finite-element-based software is proposed as the only practical way to analyze this type of structural system. Results of a large parametric study using a finite element model are presented and a method to evaluate the ultimate strength of actual columns is introduced. Finally, a simple hand design method is derived. Key words: diaphragm, design, finite element, girt, column, stability, statistics.

Strength Analyses of Sandwich Pipes for Ultra Deepwaters

2004 ◽  
Vol 72 (4) ◽  
pp. 599-608 ◽  
Author(s):  
Segen Farid Estefen ◽  
Theodoro Antoun Netto ◽  
Ilson Paranhos Pasqualino
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Ultimate Strength ◽  
Thermal Insulation ◽  
Research Work ◽  
Element Model ◽  
Material Behavior ◽  
Core Material ◽  
Small Scale ◽  
Mechanical Resistance

Design requirements for pipelines regarding both ultimate strength and flow assurance in ultra deepwater scenarios motivated the development of a new sandwich pipe which is able to combine high structural and thermal insulation properties. In this concept, the annulus is filled with low cost materials with adequate thermal insulation properties and good mechanical resistance. The aim of this research work is to perform small-scale laboratorial tests and to develop a finite element model to evaluate the structural performance of such sandwich pipes with two different options of core material. After calibrated in view of the experimental results, a three-dimensional finite element model incorporating nonlinear geometric and material behavior is employed to perform strength analyses of sandwich pipes under combined external pressure and longitudinal bending. Ultimate strength envelopes for sandwich pipes are compared with those generated for single-wall steel pipes with equivalent collapse pressures. The study shows that sandwich pipe systems with either cement or polypropylene cores are feasible options for ultra deepwater applications.

scholarly journals Experimental Study and Direct Strength Method for Cold-Formed Steel Built-Up I-Sectional Columns under Axial Compression

2021 ◽  
Vol 2021 ◽  
pp. 1-22
Author(s):  
Xingyou Yao
Keyword(s):  
Finite Element ◽  
Axial Compression ◽  
Numerical Study ◽  
Experimental Results ◽  
Distortional Buckling ◽  
Cross Sectional ◽  
Direct Strength Method ◽  
Comparison Results ◽  
Cold Formed Steel ◽  
Interactive Buckling

The objective of this paper is to investigate the buckling behavior and design method of the ultimate strength for the cold-formed steel (CFS) built-up I-sectional columns under axial compression which failed in distortional buckling and interactive buckling. A total of 56 CFS built-up I-sectional columns subjected to axial compression were tested, and the different buckling modes and ultimate strengths were analyzed in detail by varying the thickness, the length, the spacing of screws, the end fastener group, and the cross-sectional dimensions of CFS built-up I-sectional columns. It was shown in the test that noticeable interaction of local and distortional buckling or interaction of local, distortional, and global buckling was observed for the built-up I-sectional columns with different lengths and cross-sectional dimensions. A finite element model (FEM) was developed and validated with experimental results. A further parametric study has been conducted including different cross sections and slenderness ratios for the built-up I-sectional columns. The load-carrying capacities obtained from the experimental and numerical study were used to investigate the feasibility of the current direct strength method (DSM) when DSM was applied to CFS built-up I-sectional columns. The comparison results showed that the current DSM is not safe for CFS built-up columns failed in distortional buckling and interactive buckling. Therefore, the improved design formulas were proposed, and their accuracy was verified by using finite element analysis (FEA) and experimental results of CFS built-up I-sectional columns subjected to axial compression.

Numerical investigation on behaviour and design of cold-formed steel built-up column composed of lipped sigma channels

2019 ◽  
Vol 22 (8) ◽  
pp. 1817-1829 ◽  
Author(s):  
M Anbarasu
Keyword(s):  
Finite Element ◽  
Structural Response ◽  
Element Model ◽  
Width Ratio ◽  
Element Analysis ◽  
Design Strength ◽  
Steel Columns ◽  
The North ◽  
Cold Formed Steel ◽  
Ultimate Resistance

This article aims at investigating the structural response and predicting the ultimate resistance of cold-formed steel built-up columns composed of lipped sigma sections with pinned ends. For this purpose, a numerical model is established by using the finite element code ABAQUS. The finite element models include geometric, material nonlinearity. The effects of initial local and overall geometric imperfections have been taken into consideration in the finite element modelling. The results of the nonlinear finite element analysis were validated with the available experimental results present in the literature. A parametric study was carried out using the developed finite element model to study the effect of member slenderness, height-to-width ratio and depth of trapezoidal stiffener on the ultimate resistance of cold-formed steel closed built-up columns. On the basis of the parametric results, presented herein, appropriateness of the current direct strength method in the North American Specification for cold-formed steel columns is assessed. Based on such comparison, design expression is proposed to provide reliable design strength prediction of cold-formed steel built-up column composed of lipped sigma sections and verified through reliability analysis.

Sign in / Sign up

Export Citation Format

Share Document