A new concept of actively controlled rate of diesel combustion (ACCORDIC): Part II—simultaneous improvements in brake thermal efficiency and heat loss with modified nozzles

2018 ◽  
Vol 20 (1) ◽  
pp. 34-45 ◽  
Author(s):  
Noboru Uchida ◽  
Hiroki Watanabe
Keyword(s):  
Heat Release ◽  
Heat Loss ◽  
Heat Release Rate ◽  
Release Rate ◽  
Thermal Efficiency ◽  
Air Entrainment ◽  
Diesel Combustion ◽  
Brake Thermal Efficiency ◽  
Rate Profile ◽  
Late Part

A new diffusion-based combustion concept (named it as Actively Controlled Rate of Diesel Combustion) for the confirmation of brake thermal efficiency optimum heat release rate profile based on multiple fuel injectors has been investigated. The outstanding results are; it is possible to achieve desired heat release rate profile only by the independent control of injection timing and duration of three injectors installed to a cylinder. The optimum brake thermal efficiency was not achieved with the Otto-like cycle but with the Sabathe-like cycle as predicted by a zero-dimensional thermodynamic model. Furthermore, smoke emissions were concurrently reduced with NOx emissions by increasing fuel amount from the side injectors without any deterioration in CO and total hydrocarbon emissions. On the other hand, brake thermal efficiency itself was not so improved than expected, because of lower heat release in the late part of combustion and unexpected less heat loss reduction. To solve these issues, combustion visualization and numerical simulation analysis were carried out. The results suggested that the adjacent sprays with narrower angle from each side injector deteriorated air entrainment and mixture formation, which might also result in the deterioration in wall heat loss in the expansion stroke. To solve both issues simultaneously, modified nozzle to inject against the swirl from the side injectors was utilized and achieved an improvement in both brake thermal efficiency and heat loss. That is the interdependent and reciprocal control of in-cylinder flow and fuel injection will be one of the breakthrough technologies for current trade-offs by the temporal and spatial spray flame optimization. Furthermore, the nozzle having higher flow rate with less number of orifice was utilized for the side injectors. Even though the smoke emissions were not optimized yet, brake thermal efficiency was much improved with higher heat release rate in the late part of combustion.

scholarly journals Experimental and Simulation of Diesel Engine Fueled with Biodiesel with Variations in Heat Loss Model

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1622
Author(s):  
Daniel Romeo Kamta Legue ◽  
Zacharie Merlin Ayissi ◽  
Mahamat Hassane Babikir ◽  
Marcel Obounou ◽  
Henri Paul Ekobena Fouda
Keyword(s):  
Heat Release ◽  
Heat Loss ◽  
Heat Release Rate ◽  
Release Rate ◽  
Diffusion Combustion ◽  
Cylinder Wall ◽  
Compression Ignition Engine ◽  
Experimental Conditions ◽  
Load Range ◽  
Combustion Phase

This study presents an experimental investigation and thermodynamic 0D modeling of the combustion of a compression-ignition engine, fueled by an alternative fuel based on neem biodiesel (B100) as well as conventional diesel (D100). The study highlights the effects of the engine load at 50%, 75% and 100% and the influence of the heat loss models proposed by Woschni, Eichelberg and Hohenberg on the variation in the cylinder pressure. The study shows that the heat loss through the cylinder wall is more pronounced during diffusion combustion regardless of the nature of the fuels tested and the load range required. The cylinder pressures when using B100 estimated at 89 bars are relatively higher than when using D100, about 3.3% greater under the same experimental conditions. It is also observed that the problem of the high pressure associated with the use of biodiesels in engines can be solved by optimizing the ignition delay. The net heat release rate remains roughly the same when using D100 and B100 at 100% load. At low loads, the D100 heat release rate is higher than B100. The investigation shows how wall heat losses are more pronounced in the diffusion combustion phase, relative to the premix phase, by presenting variations in the curves.

scholarly journals Effects of Heat Release Rate on NOx Time History in Diesel Combustion.

1996 ◽  
Vol 62 (598) ◽  
pp. 2521-2527
Author(s):  
Takuji ISHIYAMA ◽  
Kei MIWA ◽  
Satoru WATABE ◽  
Masanori HIGASHIDA
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Time History ◽  
Diesel Combustion

scholarly journals Diesel engine performance, emissions and combustion characteristics of castor oil blends using pyrolysis

2020 ◽  
Vol 12 (12) ◽  
pp. 168781402097552
Author(s):  
Youssef A. Attai ◽  
Osayed S. Abu-Elyazeed ◽  
Mohamed R. ElBeshbeshy ◽  
Mohamed A. Ramadan ◽  
Mohamed S. Gad
Keyword(s):  
Heat Release ◽  
Fuel Consumption ◽  
Heat Release Rate ◽  
Release Rate ◽  
Thermal Efficiency ◽  
Exhaust Gas ◽  
Cylinder Pressure ◽  
Gas Oil ◽  
Gas Temperature ◽  
Exhaust Gas Temperature

Castor biodiesel (CBD) was manufactured by slow pyrolysis of oil from highly yielded seeds with anhydrous sodium hydroxide catalyst. An experimental study of engine’s performance, emissions and combustion characteristics using biodiesel blended with gas oil in volumetric ratios of 0, 10, 25, 50, 75, and 100% at different loads was performed. Increase of CBD percentage in the blend led to a reduction in engine’s thermal efficiency, cylinder pressure, net heat release rate, and smoke emission. The exhaust gas temperature, specific fuel consumption, unburned hydrocarbon, CO, and nitrogen oxide emissions were increased with the increase of CBD ratio. Biodiesel showed the maximum increase in specific fuel consumption by 10% and the thermal efficiency was decreased by 10.5% about pure diesel. Smoke emissions were decreased for CBD100 by 12% about gas oil. The maximum increases in NOx, CO, HC emissions, and exhaust gas temperature for CBD 100 were 22, 34, 48, and 11%, respectively related to diesel oil. The maximum reductions in cylinder pressure and net heat release rate were 5 and 13% for CBD100 about gas oil, respectively. Biodiesel percentage of 10% showed near values of performance parameters and emissions to gas oil, so, it is recommended as the optimum percentage.

scholarly journals The classification of gasoline/diesel dual-fuel combustion based on the heat release rate shapes and its application in a light-duty single-cylinder engine

2018 ◽  
Vol 20 (1) ◽  
pp. 69-79 ◽  
Author(s):  
Jeongwoo Lee ◽  
Sanghyun Chu ◽  
Jaegu Kang ◽  
Kyoungdoug Min ◽  
Hyunsung Jung ◽  
...  
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Thermal Efficiency ◽  
Fuel Combustion ◽  
Dual Fuel ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Dual Fuel Combustion ◽  
Compression Ignition Combustion

In this research, there are two major sections for analysis: the characteristics of gasoline and diesel dual-fuel combustion and their application to operating load extension with high thermal efficiency and low emissions. All the experiments were completed using a single-cylinder compression ignition engine with 395 cc displacement. In the first section, the dual-fuel combustion modes were classified into three cases by their heat release rate shapes. Staying at 1500 r/min with a total value of 580 J of low heat for each cycle condition, the diesel injection timing was varied from before top dead center with a 6–46 °crank angle with 70% of gasoline fraction based on the low heating value. Among the modes were two suitable dual-fuel combustion modes for a premixed compression ignition. The first suitable mode shows multiple peaks in the heat release rate (mode 2) and the second suitable mode shows a single peak with a “bell-shaped” heat release rate (mode 3). These two dual-fuel combustion types showed a high gross indicated thermal efficiency of up to 46%. Based on the results in the first section, the practical application of dual-fuel premixed compression ignition combustion was investigated considering a high thermal efficiency and a high-load condition. At a 1500 r/min/gross indicated mean effective pressure of 6.5 bar, 48% of the gross indicated thermal efficiency was obtained by using dual-fuel premixed compression ignition combustion mode 3. This mode was typical of a “reactivity controlled compression ignition,” while the nitrogen oxides and the particulate matter emissions satisfied the EURO-6 regulation (0.21 g/kW h and 2.8 mg/m3, respectively). In addition, a high thermal efficiency (45%) with low maximum pressure rise rate, NOx (nitrogen oxides), and particulate matter emissions was obtained at 2000 r/min/gross indicated mean effective pressure 14 bar condition by the adjustment of dual-fuel premixed compression ignition combustion mode 2. As a result, this research contributes to the understanding and practical application of dual-fuel combustion for a light-duty compression ignition engine.

Numerical study of the effect of split direct injection on the lean-burn combustion characteristics in a poppet-valve two-stroke gasoline engine at high loads

2020 ◽  
pp. 146808742093240
Author(s):  
Xiao Li ◽  
Bang-Quan He ◽  
Hua Zhao
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Thermal Efficiency ◽  
Direct Injection ◽  
Lean Burn ◽  
Gasoline Engines ◽  
Poppet Valve ◽  
Auto Ignition ◽  
Second Peak

Poppet-valve two-stroke gasoline engines can increase specific power of four-stroke gasoline engines with the same displacement. But knocking combustion may also occur at high loads in two-stroke engines. The application of stratified lean-burn on poppet-valve two-stroke gasoline engines can avoid knocking and increase combustion stability. To investigate the effect of the mixture stratification on lean-burn events at high loads, simulation was conducted in different split direct injection conditions with constant fuel mass when equivalence ratio is 0.625. Results show that most fuel distributes near the center of the cylinder at any second direct injection ratio ( rSOI2). At different rSOI2s, auto-ignition occurs during flame propagation, causing shortened combustion duration. Auto-ignition causes the second peak of the heat release rate. The second peak of the heat release rate first decreases and then increases with increased rSOI2. Indicated mean effective pressure and indicated thermal efficiency increase with increased maximum pressure rise rate. The maximum indicated thermal efficiency of 42% can be reached without knocking combustion at 1500 rpm. The proportion of fuel mass through auto-ignition in the cylinder is an important factor to change the indicated thermal efficiency of a lean-burn engine at high loads.

Sign in / Sign up

Export Citation Format

Share Document