scholarly journals Numerical investigation on the influence of the electro-resistance welding pipe manufacturing process on the local variation of the yield strength of the pipe material

2020 ◽  
Vol 12 (5) ◽  
pp. 168781402091780
Author(s):  
Luca Quagliato ◽  
Dongwook Kim ◽  
Donghwi Park ◽  
Naksoo Kim
Keyword(s):  
Finite Element ◽  
Yield Strength ◽  
Residual Stresses ◽  
Kinematic Hardening ◽  
Element Model ◽  
Resistance Welding ◽  
Pipe Material ◽  
Forming Process ◽  
Element Simulation ◽  
Welding Pipe

In the present research work, a finite element model of the electro-resistance welding pipe forming process chain is developed using the ABAQUS/Explicit software. The forming process, which is composed of 22 tandem roll stations, has been fully modeled in the developed finite element simulation. In order to account for the Bauschinger effect on the pipe material properties as a consequence of the loading and the unloading during the process, a non-linear kinematic hardening model has been utilized in all the proposed finite element simulation models. The constants for the non-linear kinematic hardening model were estimated by means of cyclic experiments on the K55 steel pipe material. In order to properly simulate the electric arc welding (electro-resistance welding) operation, the ABAQUS welding interface has been utilized to account for the joining between the two edges of the formed pipe as well as to assess the influence of the welding-induced temperature field on the residual stresses on the pipe material. The sizing operation, which is the final station of the electro-resistance welding process, has been also accounted in the developed finite element method model and is composed of six tandem rolls. To export and import the results between two different modules, a mapping strategy has been utilized and allowed exporting the element results, in terms of stress, strain, and temperature, and importing them into the following simulation module. Finally, in order to estimate the influence of each process station on the yield strength of the material, a finite element simple tension test simulation has been implemented in ABAQUS/Static, mapping the results of each station on the tensile specimen. This mapping operation allowed to estimate the yield stress of the material after each of the three process stations, a consequence of the residual stresses present in the material, and has been carried out on eight circumferential locations around the pipe, evenly spaced with a 22.5° angle. The model has been validated by comparing the geometrical results, in terms of average pipe diameter and thickness, obtained from the finite element model with those of the relevant industrial production, showing deviations equal to 1.25% and 1.35% (forming) and 1.29% and 1.43% (sizing), respectively, proving the reliability of the proposed process chain analysis simulation. The results will show how the process-induced residual stresses arising on the pipe material make the material yield strength to vary from station to station as well as having different values along the circumferential direction of the pipe.

Stress and Fatigue Life Modeling of Cannon Breech Closures Including Effects of Material Strength and Residual Stress

2000 ◽  
Vol 123 (1) ◽  
pp. 150-154
Author(s):  
John H. Underwood ◽  
Michael J. Glennon
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Fatigue Life ◽  
Yield Strength ◽  
Residual Stresses ◽  
Solid Mechanics ◽  
Element Model ◽  
Pressure Vessels ◽  
Material Strength ◽  
Element Analysis

Laboratory fatigue life results are summarized from several test series of high-strength steel cannon breech closure assemblies pressurized by rapid application of hydraulic oil. The tests were performed to determine safe fatigue lives of high-pressure components at the breech end of the cannon and breech assembly. Careful reanalysis of the fatigue life tests provides data for stress and fatigue life models for breech components, over the following ranges of key parameters: 380–745 MPa cyclic internal pressure; 100–160 mm bore diameter cannon pressure vessels; 1040–1170 MPa yield strength A723 steel; no residual stress, shot peen residual stress, overload residual stress. Modeling of applied and residual stresses at the location of the fatigue failure site is performed by elastic-plastic finite element analysis using ABAQUS and by solid mechanics analysis. Shot peen and overload residual stresses are modeled by superposing typical or calculated residual stress distributions on the applied stresses. Overload residual stresses are obtained directly from the finite element model of the breech, with the breech overload applied to the model in the same way as with actual components. Modeling of the fatigue life of the components is based on the fatigue intensity factor concept of Underwood and Parker, a fracture mechanics description of life that accounts for residual stresses, material yield strength and initial defect size. The fatigue life model describes six test conditions in a stress versus life plot with an R2 correlation of 0.94, and shows significantly lower correlation when known variations in yield strength, stress concentration factor, or residual stress are not included in the model input, thus demonstrating the model sensitivity to these variables.

Finite Element Simulation of Vacuum Hot Bulge Forming Process of Reactor Coolant Pump Rotor-Can

2011 ◽  
Vol 675-677 ◽  
pp. 909-912 ◽  
Author(s):  
Zhi Zhu ◽  
Li Wen Zhang ◽  
Dong Jiang Wu
Keyword(s):  
Finite Element ◽  
Physical And Mechanical Properties ◽  
Element Model ◽  
Forming Process ◽  
Coolant Pump ◽  
Creep Properties ◽  
Finite Element Software ◽  
Element Simulation ◽  
Properties Of Materials ◽  
Future Work

In this paper, a 2-D nonlinear thermo-mechanical coupled finite element model was developed to simulate the vacuum hot bulge forming process of rotor-can with the aid of finite element software MSC.Marc. Thermal physical and mechanical properties of materials vary with temperature in the model. In addition, the effects of high temperature creep properties of materials on the vacuum hot bulge forming process of rotor-can were considered. The temperature field, the stress-strain field and the displacement field of rotor-can during vacuum hot bulge forming process were calculated. This work is beneficial to understand the vacuum hot bulge forming process of rotor-can and lays a good foundation for future work.

Finite-Element Simulation of Temperature Fields and Residual Stresses in Butt Welded Joints and Comparison With Experimental Measurements

2014 ◽  
Author(s):  
Enrico Armentani ◽  
Angela Pozzi ◽  
Raffaele Sepe
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
Base Plate ◽  
Element Model ◽  
Temperature Fields ◽  
Structural Members ◽  
Temperature Dependent ◽  
Welding Temperature ◽  
Element Simulation ◽  
Surrounding Areas

Welding is used in fabrication of structures ranging from small components to large and important structures. One of the important problems associated with welded structures is development of residual stresses and deformations due to welding temperature. In fact when structures are manufactured by welding, a non-uniform temperature distribution is produced. This distribution initially causes a rapid thermal expansion followed by a thermal contraction in the weld and surrounding areas, thus generating inhomogeneous plastic deformation and residual stresses in the weldment when it is cooled. High residual stresses in regions close to the weld may promote brittle fracture, fatigue, or stress corrosion cracking. Meanwhile, distortion in base plate may reduce the buckling strength of structural members. Therefore estimating the magnitude and distribution of welding residual stresses and distortion are necessary for achieving the safest design. In the present work an elastic-plastic finite element model considering temperature dependent mechanical properties is used to evaluate residual stresses. In this study a parametric model is adopted and the elements birth and death are used in single-pass butt welded joint to simulate the weld filler variation with time. Then numerical results are compared with experimental data.

Thermal Mechanical Coupled 3D Finite Element Simulation of Large H-Beam in Hot Rolling Process

2013 ◽  
Vol 281 ◽  
pp. 484-489
Author(s):  
Pei Qi Wang ◽  
Qin He Zhang ◽  
Bao Tian Dong ◽  
Ru Po Ma
Keyword(s):  
Finite Element ◽  
Rolling Force ◽  
Element Model ◽  
Rolling Process ◽  
Forming Process ◽  
Beam Production ◽  
Element Simulation ◽  
Simulation Results ◽  
Explicit Solver ◽  
H Beam

In order to research the forming process of H-beam, based on the large H-beam production line of HN600x200, the Standard and Explicit solver of ABAQUS are synthetically used to establish finite element model for rolling process and inter-pass thermolysis process. The reciprocation multi-pass rolling process simulation procedure based on the re-meshing technology is used to simulate the whole production process form blanks to finish products, and the continuity of data is ensured. Based on the simulation results, the deformation and rolling force of the roller as well as the metal flowing law and temperature field of workpiece are discussed emphatically. The results clearly show that the displacement of roller contains the elastic deformation and the deflection, and the counterforce of left adds to the counterforce of right is about equal to the resultant force. The simulation results are compared with the measuring results, which proves the correctness of simulation.

Finite Element Simulation of Tire-Rim Interface

1989 ◽  
Vol 17 (4) ◽  
pp. 305-325 ◽  
Author(s):  
N. T. Tseng ◽  
R. G. Pelle ◽  
J. P. Chang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Finite Element Simulation ◽  
Contact Pressure ◽  
Element Model ◽  
Experimental Measurements ◽  
Inflation Pressure ◽  
Interference Fit ◽  
Element Simulation ◽  
Rubber Composite

Abstract A finite element model was developed to simulate the tire-rim interface. Elastomers were modeled by nonlinear incompressible elements, whereas plies were simulated by cord-rubber composite elements. Gap elements were used to simulate the opening between tire and rim at zero inflation pressure. This opening closed when the inflation pressure was increased gradually. The predicted distribution of contact pressure at the tire-rim interface agreed very well with the available experimental measurements. Several variations of the tire-rim interference fit were analyzed.

Redrawing Operation a Star Shape from Cylindrical Shape Using Experimental and FE Analysis

2020 ◽  
Vol 38 (1A) ◽  
pp. 25-32
Author(s):  
Waleed Kh. Jawad ◽  
Ali T. Ikal
Keyword(s):  
Finite Element ◽  
Effective Strain ◽  
Element Model ◽  
Cylindrical Shape ◽  
Element Analysis ◽  
Punch Force ◽  
Maximum Value ◽  
Element Simulation ◽  
Blank Sheet ◽  
The Finite Element Model

The aim of this paper is to design and fabricate a star die and a cylindrical die to produce a star shape by redrawing the cylindrical shape and comparing it to the conventional method of producing a star cup drawn from the circular blank sheet using experimental (EXP) and finite element simulation (FES). The redrawing and drawing process was done to produce a star cup with the dimension of (41.5 × 34.69mm), and (30 mm). The finite element model is performed via mechanical APDL ANSYS18.0 to modulate the redrawing and drawing operation. The results of finite element analysis were compared with the experimental results and it is found that the maximum punch force (39.12KN) recorded with the production of a star shape drawn from the circular blank sheet when comparing the punch force (32.33 KN) recorded when redrawing the cylindrical shape into a star shape. This is due to the exposure of the cup produced drawn from the blank to the highest tensile stress. The highest value of the effective stress (709MPa) and effective strain (0.751) recorded with the star shape drawn from a circular blank sheet. The maximum value of lamination (8.707%) is recorded at the cup curling (the concave area) with the first method compared to the maximum value of lamination (5.822%) recorded at the cup curling (the concave area) with the second method because of this exposure to the highest concentration of stresses. The best distribution of thickness, strains, and stresses when producing a star shape by

3D Finite Element Simulation for Turning of Hardened 45 Steel

2019 ◽  
Vol 13 (2) ◽  
pp. 181-188
Author(s):  
Meng Liu ◽  
Guohe Li ◽  
Xueli Zhao ◽  
Xiaole Qi ◽  
Shanshan Zhao
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Cutting Force ◽  
Finite Element Simulation ◽  
Orthogonal Experiment ◽  
Element Model ◽  
3D Finite Element ◽  
Element Simulation ◽  
Metal Machining ◽  
Single Factor Experiment

Background: Finite element simulation has become an important method for the mechanism research of metal machining in recent years. Objective: To study the cutting mechanism of hardened 45 steel (45HRC), and improve the processing efficiency and quality. Methods: A 3D oblique finite element model of traditional turning of hardened 45 steel based on ABAQUS was established in this paper. The feasibility of the finite element model was verified by experiment, and the influence of cutting parameters on cutting force was predicted by single factor experiment and orthogonal experiment based on simulation. Finally, the empirical formula of cutting force was fitted by MATLAB. Besides, a lot of patents on 3D finite element simulation for metal machining were studied. Results: The results show that the 3D oblique finite element model can predict three direction cutting force, the 3D chip shape, and other variables of metal machining and the prediction errors of three direction cutting force are 5%, 9.02%, and 8.56%. The results of single factor experiment and orthogonal experiment are in good agreement with similar research, which shows that the model can meet the needs for engineering application. Besides, the empirical formula and the prediction results of cutting force are helpful for the parameters optimization and tool design. Conclusion: A 3D oblique finite element model of traditional turning of hardened 45 steel is established, based on ABAQUS, and the validation is carried out by comparing with experiment.

Sign in / Sign up

Export Citation Format

Share Document