A reality check on full-wave inversion applied to land seismic data for near-surface modeling

2022 ◽  
Vol 41 (1) ◽  
pp. 40-46
Author(s):  
Öz Yilmaz ◽  
Kai Gao ◽  
Milos Delic ◽  
Jianghai Xia ◽  
Lianjie Huang ◽  
...  
Keyword(s):  
Wave Velocity ◽  
Seismic Data ◽  
Surface Modeling ◽  
P Wave ◽  
Borehole Data ◽  
Near Surface ◽  
Traveltime Tomography ◽  
Wave Inversion ◽  
Full Wave ◽  
Elastic Inversion

We evaluate the performance of traveltime tomography and full-wave inversion (FWI) for near-surface modeling using the data from a shallow seismic field experiment. Eight boreholes up to 20-m depth have been drilled along the seismic line traverse to verify the accuracy of the P-wave velocity-depth model estimated by seismic inversion. The velocity-depth model of the soil column estimated by traveltime tomography is in good agreement with the borehole data. We used the traveltime tomography model as an initial model and performed FWI. Full-wave acoustic and elastic inversions, however, have failed to converge to a velocity-depth model that desirably should be a high-resolution version of the model estimated by traveltime tomography. Moreover, there are significant discrepancies between the estimated models and the borehole data. It is understandable why full-wave acoustic inversion would fail — land seismic data inherently are elastic wavefields. The question is: Why does full-wave elastic inversion also fail? The strategy to prevent full-wave elastic inversion of vertical-component geophone data trapped in a local minimum that results in a physically implausible near-surface model may be cascaded inversion. Specifically, we perform traveltime tomography to estimate a P-wave velocity-depth model for the near-surface and Rayleigh-wave inversion to estimate an S-wave velocity-depth model for the near-surface, then use the resulting pairs of models as the initial models for the subsequent full-wave elastic inversion. Nonetheless, as demonstrated by the field data example here, the elastic-wave inversion yields a near-surface solution that still is not in agreement with the borehole data. Here, we investigate the limitations of FWI applied to land seismic data for near-surface modeling.

Iterative P-wave velocity inversion using Markov chain Monte Carlo method

2020 ◽  
Author(s):  
Hyunggu Jun ◽  
Hyeong-Tae Jou ◽  
Han-Joon Kim ◽  
Sang Hoon Lee
Keyword(s):  
Wave Velocity ◽  
Seismic Data ◽  
Velocity Structure ◽  
Low Frequency ◽  
P Wave ◽  
Velocity Analysis ◽  
Seismic Section ◽  
Traveltime Tomography ◽  
P Wave Velocity ◽  
Frequency Components

<p>Imaging the subsurface structure through seismic data needs various information and one of the most important information is the subsurface P-wave velocity. The P-wave velocity structure mainly influences on the location of the reflectors during the subsurface imaging, thus many algorithms has been developed to invert the accurate P-wave velocity such as conventional velocity analysis, traveltime tomography, migration velocity analysis (MVA) and full waveform inversion (FWI). Among those methods, conventional velocity analysis and MVA can be widely applied to the seismic data but generate the velocity with low resolution. On the other hands, the traveltime tomography and FWI can invert relatively accurate velocity structure, but they essentially need long offset seismic data containing sufficiently low frequency components. Recently, the stochastic method such as Markov chain Monte Carlo (McMC) inversion was applied to invert the accurate P-wave velocity with the seismic data without long offset or low frequency components. This method uses global optimization instead of local optimization and poststack seismic data instead of prestack seismic data. Therefore, it can avoid the problem of the local minima and limitation of the offset. However, the accuracy of the poststack seismic section directly affects the McMC inversion result. In this study, we tried to overcome the dependency of the McMC inversion on the poststack seismic section and iterative workflow was applied to the McMC inversion to invert the accurate P-wave velocity from the simple background velocity and inaccurate poststack seismic section. The numerical test showed that the suggested method could successfully invert the subsurface P-wave velocity.</p>

Basin-wide empirical rock-physics transform and its application in Campeche Basin

2021 ◽  
Vol 40 (3) ◽  
pp. 178-185
Author(s):  
Yangjun (Kevin) Liu ◽  
Jonathan Hernandez Casado ◽  
Mohamed El-Toukhy ◽  
Shenghong Tai
Keyword(s):  
Pore Pressure ◽  
Wave Velocity ◽  
Effective Stress ◽  
Seismic Data ◽  
Sedimentary Basin ◽  
Rock Physics ◽  
P Wave ◽  
Rock Properties ◽  
Borehole Data ◽  
P Wave Velocity

Rock properties in the subsurface are of major importance for evaluating the petroleum prospectivity of a sedimentary basin. The key rock properties to understand are porosity, density, temperature, effective stress, and pore pressure. These rock properties can be obtained or calculated when borehole data are available. However, borehole data are usually sparse, especially in frontier basins. We propose some simple rock-physics transforms for converting P-wave velocity to other rock properties. We found that these rock-physics transforms are predictive in the east and west sides of Campeche Basin. The proposed rock-physics transforms can be used to obtain laterally varying rock properties based on information derived from seismic data.

Poststack, prestack, and joint inversion of P- and S-wave data for Morrow A sandstone characterization

2015 ◽  
Vol 3 (3) ◽  
pp. SZ59-SZ92 ◽  
Author(s):  
Paritosh Singh ◽  
Thomas L. Davis ◽  
Bryan DeVault
Keyword(s):  
Wave Velocity ◽  
Seismic Data ◽  
Joint Inversion ◽  
Wave Impedance ◽  
P Wave ◽  
S Wave ◽  
Wave Data ◽  
Wave Inversion ◽  
Density Maps ◽  
P Wave Velocity

Exploration for oil-bearing Morrow sandstones using conventional seismic data/methods has a startlingly low success rate of only 3%. The S-wave velocity contrast between the Morrow shale and A sandstone is strong compared with the P-wave velocity contrast, and, therefore, multicomponent seismic data could help to characterize these reservoirs. The SV and SH data used in this study are generated using S-wave data from horizontal source and horizontal receiver recording. Prestack P- and S-wave inversions, and joint P- and S-wave inversions, provide estimates of P- and S-wave impedances, and density for characterization of the Morrow A sandstone. Due to the weak P-wave amplitude-versus-angle response at the Morrow A sandstone top, the density and S-wave impedance estimated from joint P- and S-wave inversions were inferior to the prestack S-wave inversion. The inversion results were compared with the Morrow A sandstone thickness and density maps obtained from well logs to select the final impedance and density volume for interpretation. The P-wave impedance estimated from prestack P-wave data, as well as density and S-wave impedance estimated from prestack SV‐wave data were used to identify the distribution, thickness, quality, and porosity of the Morrow A sandstone. The stratal slicing method was used to get the P- and S-wave impedances and density maps. The S-wave impedance characterizes the Morrow A sandstone distribution better than the P-wave impedance throughout the study area. Density estimation from prestack inversion of SV data was able to distinguish between low- and high-quality reservoirs. The porosity volume was estimated from the density obtained from prestack SV-wave inversion. We found some possible well locations based on the interpretation.

Characterization of elastic properties of near-surface and subsurface deepwater hydrate-bearing sediments

Geophysics ◽  
2013 ◽  
Vol 78 (3) ◽  
pp. D169-D179 ◽  
Author(s):  
Zijian Zhang ◽  
De-hua Han ◽  
Daniel R. McConnell
Keyword(s):  
Wave Velocity ◽  
Elastic Constants ◽  
Gas Hydrate ◽  
Effective Medium Theory ◽  
Pore Space ◽  
Seismic Interpretation ◽  
P Wave ◽  
Near Surface ◽  
Free Gas ◽  
Hydrate Bearing Sediments

Hydrate-bearing sands and shallow nodular hydrate are potential energy resources and geohazards, and they both need to be better understood and identified. Therefore, it is useful to develop methodologies for modeling and simulating elastic constants of these hydrate-bearing sediments. A gas-hydrate rock-physics model based on the effective medium theory was successfully applied to dry rock, water-saturated rock, and hydrate-bearing rock. The model was used to investigate the seismic interpretation capability of hydrate-bearing sediments in the Gulf of Mexico by computing elastic constants, also known as seismic attributes, in terms of seismic interpretation, including the normal incident reflectivity (NI), Poisson’s ratio (PR), P-wave velocity ([Formula: see text]), S-wave velocity ([Formula: see text]), and density. The study of the model was concerned with the formation of gas hydrate, and, therefore, hydrate-bearing sediments were divided into hydrate-bearing sands, hydrate-bearing sands with free gas in the pore space, and shallow nodular hydrate. Although relations of hydrate saturation versus [Formula: see text] and [Formula: see text] are different between structures I and II gas hydrates, highly concentrated hydrate-bearing sands may be interpreted on poststack seismic amplitude sections because of the high NI present. The computations of elastic constant implied that hydrate-bearing sands with free gas could be detected with the crossplot of NI and PR from prestack amplitude analysis, and density may be a good hydrate indicator for shallow nodular hydrate, if it can be accurately estimated by seismic methods.

Full Wave and Down-Going Elastic Inversion of Deepwater OBN Seismic Data: Example from Niger Delta

2020 ◽  
Author(s):  
S. Amoyedo ◽  
E. Tawile ◽  
S. Pou-Palome ◽  
P. Kakaire ◽  
O. Olagundoye ◽  
...  
Keyword(s):  
Seismic Data ◽  
Niger Delta ◽  
Full Wave ◽  
Elastic Inversion

Using Seismic Data to Predict Shale Pore Pressure and Overpressure Sweet Spots: A Case Study from the Lower Silurian Longmaxi Formation in Sichuan Basin, China

2021 ◽  
Author(s):  
Sheng Chen ◽  
Qingcai Zeng ◽  
Xiujiao Wang ◽  
Qing Yang ◽  
Chunmeng Dai ◽  
...  
Keyword(s):  
Prediction Model ◽  
Wave Velocity ◽  
Shale Gas ◽  
Seismic Data ◽  
P Wave ◽  
Formation Pressure ◽  
S Wave ◽  
P Wave Velocity ◽  
New Formation ◽  
Sweet Spots

Abstract Practices of marine shale gas exploration and development in south China have proved that formation overpressure is the main controlling factor of shale gas enrichment and an indicator of good preservation condition. Accurate prediction of formation pressure before drilling is necessary for drilling safety and important for sweet spots predicting and horizontal wells deploying. However, the existing prediction methods of formation pore pressures all have defects, the prediction accuracy unsatisfactory for shale gas development. By means of rock mechanics analysis and related formulas, we derived a formula for calculating formation pore pressures. Through regional rock physical analysis, we determined and optimized the relevant parameters in the formula, and established a new formation pressure prediction model considering P-wave velocity, S-wave velocity and density. Based on regional exploration wells and 3D seismic data, we carried out pre-stack seismic inversion to obtain high-precision P-wave velocity, S-wave velocity and density data volumes. We utilized the new formation pressure prediction model to predict the pressure and the spatial distribution of overpressure sweet spots. Then, we applied the measured pressure data of three new wells to verify the predicted formation pressure by seismic data. The result shows that the new method has a higher accuracy. This method is qualified for safe drilling and prediction of overpressure sweet spots for shale gas development, so it is worthy of promotion.

scholarly journals The potential of seismic cross-hole tomography for geotechnical site investigation

2019 ◽  
Vol 92 ◽  
pp. 18006
Author(s):  
Yannick Choy Hing Ng ◽  
William Danovan ◽  
Taeseo Ku
Keyword(s):  
Wave Velocity ◽  
Site Investigation ◽  
Velocity Model ◽  
P Wave ◽  
Reconstruction Technique ◽  
Sufficient Information ◽  
Eastern Region ◽  
S Wave ◽  
Near Surface ◽  
Soil Layers

Seismic cross-hole tomography has been commonly used in oil and gas exploration and the mining industry for the detection of precious resources. For near-surface geotechnical site investigation, this geophysical method is relatively new and can be used to supplement traditional methods such as the standard penetration test, coring and sampling, thus improving the effectiveness of site characterization. This paper presents a case study which was carried out on a reclaimed land in the Eastern region of Singapore. A seismic cross-hole test was performed by generating both compressional waves and shear waves into the ground. The signals were interpreted by using first-arrival travel time wave tomography and the arrival times were subsequently inverted using Simultaneous Iterative Reconstruction Technique (SIRT). A comparison with the borehole logging data indicated that P-wave velocity model cannot provide sufficient information about the soil layers, especially when the ground water table is near the surface. The S-wave velocity model seemed to agree quite well with the variation in the SPT-N value and could identify to a certain extent the interface between the different soil layers. Finally, P-wave and S-wave velocities are used to compute the Poisson's ratio distribution which gave a good indication of the degree of saturation of the soil.

Sign in / Sign up

Export Citation Format

Share Document