scholarly journals Seismic Demands in Column Base Connections of Steel Moment Frames

2018 ◽  
Vol 34 (3) ◽  
pp. 1383-1403 ◽  
Author(s):  
Pablo Torres-Rodas ◽  
Farzin Zareian ◽  
Amit Kanvinde
Keyword(s):  
Time History ◽  
Base Plate ◽  
Moment Frames ◽  
Steel Moment Frames ◽  
Seismic Demands ◽  
Axial Forces ◽  
Plate Connections ◽  
Nonlinear Time History ◽  
Base Connections ◽  
Column Base

Methods for the seismic design of base connections in steel moment frames are well-developed and routinely utilized by practicing engineers. However, design loads for these connections are not verified by rigorous analysis. This knowledge gap is addressed through nonlinear time history simulations using design-level seismic excitation that interrogate demands in column base connections in 2-, 4-, 8-, and 12-story steel moment frames, featuring base connections that reflect current U.S. practice. The results indicate that: (1) for exposed base plate connections, lower bound (rather than peak) estimates of axial compression are suitable for design because higher axial forces increase connection strength by delaying base plate uplift; (2) even when designed as pinned (as in low-rise frames), base connections carry significant moment, which can be estimated only through accurate representation of base flexibility; and (3) the failure of embedded base connections is controlled by moment, which may be estimated either through overstrength or capacity-based calculations.

scholarly journals Comparison of Novel Seismic Protection Devices to Attenuate the Earthquake Induced Energy

Actuators ◽  
2021 ◽  
Vol 10 (4) ◽  
pp. 73
Author(s):  
Osman Hansu ◽  
Esra Mete Güneyisi
Keyword(s):  
Lateral Displacement ◽  
Time History ◽  
Seismic Protection ◽  
Base Shear ◽  
Seismic Demands ◽  
Nonlinear Time History Analyses ◽  
History Of ◽  
Protection Devices ◽  
Nonlinear Time History ◽  
Better Than

This study addresses an alternative use of viscous dampers (VDs) associated with buckling restrained braces (BRBs) as innovative seismic protection devices. For this purpose, 4-, 8- and 12-story steel bare frames were designed with 6.5 m equal span length and 4 m story height. Thereafter, they were seismically improved by mounting the VDs and BRBs in three patterns, namely outer bays, inner bays, and all bays over the frame heights. The structures were modeled using SAP 2000 software and evaluated by the nonlinear time history analyses subjected to the six natural ground motions. The seismic responses of the structures were investigated for the lateral displacement, interstory drift, absolute acceleration, maximum base shear, and time history of roof displacement. The results clearly indicated that the VDs and BRBs reduced seismic demands significantly compared to the bare frame. Moreover, the all-bay pattern performed better than the others.

Investigation of Damages in RC Frames Under Near Field Earthquakes Using a Damage Index

2016 ◽  
Vol 16 (02) ◽  
pp. 1450094 ◽  
Author(s):  
Seyed Morteza Zinati Yazdi ◽  
Mohammad Taghi Kazemi
Keyword(s):  
Near Field ◽  
Damage Index ◽  
Time History ◽  
General Rule ◽  
Nonlinear Time History Analysis ◽  
Far Field ◽  
Moment Frames ◽  
Moment Frame ◽  
Rc Frames ◽  
Nonlinear Time History

Heavy damages on structures caused by near field earthquakes in recent years has brought serious attention to this problem. An examination of previous records has shown significant differences for near field earthquakes, including a large energy pulse, unlike far field earthquakes. But as a general rule, the effects of near field earthquakes have been ignored in most building codes. The purpose of this paper is to investigate the effect of near field earthquakes on reinforced concrete (RC) moment frames. To achieve this goal, the Erduran damage index, an efficient way to calculate damage, was employed to analyze two 4- and 8-story RC moment frame buildings. The buildings with moderate and high ductility were designed by the strength criteria. Seven pairs of near field and far field earthquakes were scaled and used for dynamic nonlinear time history analysis. Using Erduran’s beam and column damage index, respectively, based on rotation and drift, the results from both near and far field earthquakes were compared. Moreover, for better assessment, 4-story buildings were evaluated from the performance based viewpoint of design. We observe from the results that most of the components of the structures under near field earthquakes sustained severe damages and in some cases even component failure. Components of the structures under near field earthquakes suffered from 30% more of damage, on average, than that under far field earthquakes.

scholarly journals A simple method for determining seismic demands on gravity load frames

2017 ◽  
Vol 44 (8) ◽  
pp. 661-673 ◽  
Author(s):  
J. Beauchamp ◽  
P. Paultre ◽  
P. Léger
Keyword(s):  
Response Spectrum ◽  
Time History ◽  
Bending Moment ◽  
New Method ◽  
Simple Method ◽  
Seismic Demands ◽  
Gravity Load ◽  
Comparison Results ◽  
Seismic Force ◽  
Nonlinear Time History

This paper presents a simple method based on modal response spectrum analysis to compute internal forces in structural elements belonging to gravity framing not part of the seismic force resisting system (SFRS). It is required that demands on these gravity load resisting system (GLRS) be determined according to the design displacement profile of the SFRS. The proposed new method uses the fact that if the linear stiffness properties of the GLRS not part of the SFRS have negligible values compared to those of the SFRS, only the latter will provide lateral resistance. Displacements of the GLRS then correspond to those of the SFRS alone. The new method is illustrated by computing the seismic responses of a symmetric and an asymmetric multi-storey reinforced concrete building. These results are compared to those obtained from the application of the simplified analysis method proposed in the Canadian standard for the design of concrete structures. Nonlinear time history analyses are also performed to provide a benchmark for comparison. Results show that the new method can predict shear and bending moment in all members at once with ease. Therefore, this new simplified method can effectively be used to predict seismic forces in elements not considered part of the SFRS.

Optimization Design of Large Span Cable-Stayed Bridge in High Seismic Risk Zone

2013 ◽  
Vol 353-356 ◽  
pp. 2015-2019
Author(s):  
Zhi Hua Xiong ◽  
Yun Cheng Feng ◽  
Song Lin Song ◽  
Jiang Bo Wang
Keyword(s):  
Optimization Design ◽  
Time History ◽  
Nonlinear Time History Analysis ◽  
Seismic Safety ◽  
Seismic Demands ◽  
Large Span ◽  
Cable Stayed Bridge ◽  
History Analysis ◽  
Ductile Steel ◽  
Nonlinear Time History

To ensure seismic safety of a large span cable-stayed bridge, two alternative pylon shapes and section types were studied. Nonlinear time history analysis was performed in the context. It is found that the A-shaped pylon is much stiffener than the H-shaped pylon in terms of deformation. The steel A-shaped pylon can significantly reduce the seismic demands of the key member including tower drift and moment. A ductile steel link between towers is proposed for the optimization of design in the paper. The A-shaped reinforced concrete tower with ductile steel link was proved to be a relatively balanced plan considering engineering, aesthetic and economic factors.

Influence of Earthquake Attack Angle on Seismic Demands for Structures under Bi-Directional Ground Motions

2011 ◽  
Vol 255-260 ◽  
pp. 2330-2334 ◽  
Author(s):  
Yu Zhang ◽  
Quan Wang Li ◽  
Jian Sheng Fan
Keyword(s):  
Seismic Design ◽  
Ground Motions ◽  
Time History ◽  
Earthquake Excitation ◽  
Seismic Demands ◽  
3 Dimensional ◽  
Nonlinear Time History Analyses ◽  
Modification Factor ◽  
Structural Responses ◽  
Nonlinear Time History

The earthquake may attack the structural building from any angle, but in current seismic design codes, this type of uncertainty is seldom accounted. The uncertainty associated with the direction of earthquake excitation was considered in this paper, and its effect on structural responses was investigated. For this purpose, a simple 3-dimensional model with symmetric plan was established, which had fundamental periods ranged from 0.1s to 5.0s, and was subjected to a set of 30 ground motion pairs for which both linear and nonlinear time history analyses were performed. Analyzing results showed that, on average, the elastic roof acceleration is 32% underestimated, and the inelastic roof displacement is 18% underestimated if the variation of earthquake excitation direction is not consider. Recognizing this, a modification factor for the seismic demand was proposed thorough a statistical analysis, which guarantees a probability of 95% design safety

Sign in / Sign up

Export Citation Format

Share Document