Application of the microplane model for three-dimensional reversed-cyclic analysis of reinforced concrete members

2021 ◽  
pp. 51-59
Author(s):  
M. Hoehler ◽  
J. Ožbolt
Keyword(s):  
Reinforced Concrete ◽  
Three Dimensional ◽  
Microplane Model ◽  
Concrete Members ◽  
Reversed Cyclic

scholarly journals Study Numerical Simulation of Stress-Strain Behavior of Reinforced Concrete Bar in Soil using Theoretical Models

2019 ◽  
Vol 5 (11) ◽  
pp. 2349-2358
Author(s):  
Ali Sabah Al Amli ◽  
Nadhir Al-Ansari ◽  
Jan Laue
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Three Dimensional ◽  
Theoretical Models ◽  
Element Model ◽  
Stress Strain ◽  
Strain Behavior ◽  
Concrete Members ◽  
Steel Bar ◽  
Three Dimensional Finite Element

Nonlinear analysis for reinforced concrete members (R.C.) with two types of bars also with unsaturated and saturated soils was used to represent the models. To control the corrosion in the steel bar that used in R.C. member and decrease the cost, the geogrid with steel bar reinforcement are taken in this study to determine the effect of load-deflection and stress-strain relationships. The finite element method is used to model the R.C. member, bars and soil. A three-dimensional finite element model by ABAQUS version 6.9 software program is used to predict the load versus deflection and stress versus strain response with soil. The results for the model in this study are compared with the experimental results from other research, and the results are very good. Therefore, it was concluded that the models developed in this study can accurately capture the behavior and predict the load-carrying capacity of such R.C. members with soil and the maximum stresses with strains. The results show plastic strain values in the R.C. member with saturated soil are larger than their values in unsaturated soil about (54%, 58%, and 55% and 52%) when the geogrid ratios are (without geogrid, 60%, 40% and 20%) respectively, with the same values of stresses.

scholarly journals Predicting shear failure in reinforced concrete members using a three-dimensional peridynamic framework

2021 ◽  
Author(s):  
Mark Hobbs ◽  
Gabriel Hattorri ◽  
John Orr
Keyword(s):  
Reinforced Concrete ◽  
Failure Modes ◽  
Shear Failure ◽  
Load Transfer ◽  
Three Dimensional ◽  
Constitutive Law ◽  
Concrete Members ◽  
Predictive Error ◽  
Wide Range ◽  
Transfer Mechanisms

The assumptions made in design codes can result in unconservative predictions of shear strength for reinforced concrete members. The limitations of empirical methods have prompted the development and use of numerical techniques. A three-dimensional bond-based peridynamic framework is developed for predicting shear failure in reinforced concrete members. The predictive accuracy and generality of the framework is assessed against existing experimental results. Nine reinforced concrete beams that exhibit a wide range of failure modes are modelled. The shear-span-to-depth ratio is systematically varied from 1 to 8 to facilitate a study of different load-transfer mechanisms and failure modes. A comprehensive validation study such as this has until now been missing in the peridynamic literature. A bilinear constitutive law is employed, and the sensitivity of the model is tested using two levels of mesh refinement. The predictive error between the experimental and numerical failure loads ranges from +3% to -57%, highlighting the importance of validation against a series of problems. The results demonstrate that the model captures many of the factors that contribute to shear and bending resistance. New insights into the capabilities and deficiencies of the peridynamic model are gained by comparing the expected load-transfer mechanisms with the predictive error.

Sign in / Sign up

Export Citation Format

Share Document