A preliminary study of the load bearing capacity of a new foil thrust gas bearing

2010 ◽  
Vol 225 (3) ◽  
pp. 673-678 ◽  
Author(s):  
R G Chen ◽  
Q Zhou ◽  
Y Liu ◽  
Y Hou
Keyword(s):  
High Speed ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Rapid Development ◽  
Experimental Investigations ◽  
Simple Type ◽  
Preliminary Measurement ◽  
Foil Bearings ◽  
Compliant Structure ◽  
Gas Bearing

With the rapid development of high-speed, oil-free turbomachinery, more and more attention is concentrated on compliant aerodynamic foil bearings. However, the common corrugated bump foil forming the compliant structure is so complicated that manufacturing it is time-consuming and troublesome. In this article, a simple type of aerodynamic foil thrust gas bearing with an elastic hemispherical convex dot support configuration is first proposed. Then experimental investigations on stability and its load capacity characteristic for this foil thrust bearing were conducted on a multi-functional thrust bearing test rig. The preliminary measurement and analysis are presented through the wave and spectrum of axial displacement response in the time and frequency domain. It is demonstrated that the proposed bearing can operate well and has good stability in tests, and experimental results show that the axial load can reach 25 N when the rotational speed is about 114 200 r/min.

Development of Foil Thrust Bearings with Simple Structure for Micro Turbines

2011 ◽  
Vol 368-373 ◽  
pp. 1392-1395 ◽  
Author(s):  
Quan Zhou ◽  
Yu Hou ◽  
Ru Gang Chen
Keyword(s):  
High Speed ◽  
Simple Structure ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Complicated Structure ◽  
Thrust Bearings ◽  
Foil Bearings ◽  
Rotational Systems ◽  
Micro Turbine ◽  
Foil Thrust Bearing

Because of the low power loss and high stability, foil bearings are suitable lubrication components for high speed rotational systems. At present, the foil bearings used in actual applications almost have complicated structure and are hard to manufacture. In this paper, two kinds of foil thrust bearings with simple structure are presented. Configurations of these two foil thrust bearings are introduced; meanwhile, the load capacity and running stability are also tested in a high speed micro turbine. It is shown that viscoelastic supported foil thrust bearing has higher load capacity and hemisphere convex dots supported foil thrust bearing is more stable in high speed operational condition.

A New Foil Gas Bearing With Compression Springs as Compliant Structure for Microturbomachinery Applications

2006 ◽  
Author(s):  
Ju-Ho Song ◽  
Daejong Kim
Keyword(s):  
Critical Speed ◽  
Hydrodynamic Instability ◽  
Load Capacity ◽  
Viscous Damping ◽  
Equivalent Viscous Damping ◽  
Foil Bearings ◽  
Compliant Structure ◽  
Air Supply ◽  
Compression Springs ◽  
Gas Bearing

A new foil gas bearing is introduced in this paper. This foil gas bearing uses series of compression springs as a compliant structure instead of expensive corrugated bump foils. The new foil gas bearing is very simple in structure and easy to manufacture. A theoretical model to estimate stiffness and damping of the spring bump was developed. Measured stiffnesses of individual spring bump agree well with predictions. Load capacity was measured up to 62.5 N at 20,000rpm with both cooled and uncooled bearings. Initial selection of spring geometry rendered rather soft supports compared to other bump foil bearings, and allowed only limited load during the test. Developed cooling method using direct air supply holes machined on the bearing sleeve was very effective to cool the test bearing because the spring bumps are not connected along the circumferential direction, and allow very effective circumferential distribution of cooling air. A series of orbit simulation was performed to estimate critical speed and onset speed of instability. Bump dynamics was directly coupled with the orbit simulation. Critical speed was estimated at around 7500 rpm due to relatively soft support structure. Hydrodynamic instability with WFR 0.5 could be predicted at around 15,000 rpm. The rotor instability is predicted even under the equivalent viscous damping extracted from bump dynamics, implying the viscous damping alone within the bump cannot suppress hydrodynamic instability of foil bearings.

A High Speed Test Rig Capable of Running at 190,000rpm to Characterize Gas Foil Thrust Bearings

2018 ◽  
Author(s):  
Nguyen T. LaTray ◽  
Daejong Kim
Keyword(s):  
High Speed ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Test Facility ◽  
Frictional Torque ◽  
Test Rig ◽  
Speed Test ◽  
Compliant Structure ◽  
Bearing Load ◽  
Speed Up

This paper details the design and performance of a high-speed (up to 190,000rpm) gas foil thrust bearing (GFTB) test rig to measure bearing load capacity. Several GFTB test rigs were reported in the literature for operating speed up to 90krpm. A few recently presented works show successful runs at 135krpm for testing gas thrust bearing with viscoelastic support and 130krpm tilting pad thrust bearing with compliant structure. However, a GFTB test rig for speed range over 100krpm has not been reported. At high speed operation, the gas film thickness of the GFTB is around a few microns which makes it difficult to achieve in testing. In many cases, the measured thrust load from experiments is well below the predicted data due to difficulty in testing and instrumentation. Difficulty in validating the actual load capacity of the bearings leads to increasing the thrust bearing size to ensure sufficient load capacity in actual applications, which results in higher power consumption. This work presents detail feature of a novel GFTB test rig and test results of 38mm GFTB. The developed test rig runs up to 190krpm and measures bearing load capacity, frictional torque and temperature across bearing ID and OD. The test rig is suitable for testing GFTB with OD from 30 mm to 40 mm. The test facility successfully tests a 38 mm GFTB to its predicted load capacity of 75N (110kPa).

Numerical and experimental studies on the thermal and static characteristics of multi-leaf foil thrust bearing

2021 ◽  
pp. 135065012110110
Author(s):  
Yu Guo ◽  
Yu Hou ◽  
Qi Zhao ◽  
Xionghao Ren ◽  
Shuangtao Chen ◽  
...  
Keyword(s):  
High Speed ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Failure Process ◽  
Experimental Studies ◽  
Elastic Model ◽  
Static Characteristics ◽  
Bearing Load ◽  
Foil Thrust Bearing ◽  
Cooling Air

Foil bearing is considered to be a promising supporting technology in high-speed centrifugal machinery. Due to the high-speed shearing effect in the viscous lubricant film, heat generation could not be ignored. In this paper, a thermo-elastic model of the multi-leaf foil thrust bearing is proposed to predict its thermal and static characteristics. In the model, modified Reynolds equation, energy equation, and Kirchhoff equation are solved in a coupling way. The contact area between the foil and welding plate is taken into account. Besides, the effect of cooling air on the bearing temperature is investigated. The ultimate load capacity and transient overload failure process of the bearing is analyzed and discussed. The effect of rotation speed on the bearing temperature is more obvious than that of the bearing load. The bearing temperature drops obviously by introducing the cooling air, and the cooling effect is improved with the supply pressure. The transient overload failure of the bearing occurs when the bearing load exceeds the ultimate value.

Foil Gas Bearing With Compression Springs: Analyses and Experiments

2007 ◽  
Vol 129 (3) ◽  
pp. 628-639 ◽  
Author(s):  
Ju-ho Song ◽  
Daejong Kim
Keyword(s):  
Loss Factor ◽  
Load Capacity ◽  
Underlying Structure ◽  
Equivalent Viscous Damping ◽  
Foil Bearings ◽  
Foil Bearing ◽  
Different Types ◽  
Structural Loss ◽  
Compression Springs ◽  
Gas Bearing

A new foil gas bearing with spring bumps was constructed, analyzed, and tested. The new foil gas bearing uses a series of compression springs as compliant underlying structures instead of corrugated bump foils. Experiments on the stiffness of the spring bumps show an excellent agreement with an analytical model developed for the spring bumps. Load capacity, structural stiffness, and equivalent viscous damping (and structural loss factor) were measured to demonstrate the feasibility of the new foil bearing. Orbit and coast-down simulations using the calculated stiffness and measured structural loss factor indicate that the damping of underlying structure can suppress the maximum peak at the critical speed very effectively but not the onset of hydrodynamic rotor-bearing instability. However, the damping plays an important role in suppressing the subsynchronous vibrations under limit cycles. The observation is believed to be true with any air foil bearings with different types of elastic foundations.

Rotordynamic Performance of a Rotor Supported on Bump Type Foil Gas Bearings: Experiments and Predictions

2006 ◽  
Vol 129 (3) ◽  
pp. 850-857 ◽  
Author(s):  
Luis San Andrés ◽  
Dario Rubio ◽  
Tae Ho Kim
Keyword(s):  
High Speed ◽  
Critical Speed ◽  
Load Capacity ◽  
Test System ◽  
Foil Bearings ◽  
Rotor Imbalance ◽  
Synchronous Motion ◽  
Damping Characteristics ◽  
Rotor Surface ◽  
Stiffness And Damping

Gas foil bearings (GFBs) satisfy the requirements for oil-free turbomachinery, i.e., simple construction and ensuring low drag friction and reliable high speed operation. However, GFBs have a limited load capacity and minimal damping, as well as frequency and amplitude dependent stiffness and damping characteristics. This paper provides experimental results of the rotordynamic performance of a small rotor supported on two bump-type GFBs of length and diameter equal to 38.10mm. Coast down rotor responses from 25krpm to rest are recorded for various imbalance conditions and increasing air feed pressures. The peak amplitudes of rotor synchronous motion at the system critical speed are not proportional to the imbalance introduced. Furthermore, for the largest imbalance, the test system shows subsynchronous motions from 20.5krpm to 15krpm with a whirl frequency at ∼50% of shaft speed. Rotor imbalance exacerbates the severity of subsynchronous motions, thus denoting a forced nonlinearity in the GFBs. The rotor dynamic analysis with calculated GFB force coefficients predicts a critical speed at 8.5krpm, as in the experiments; and importantly enough, unstable operation in the same speed range as the test results for the largest imbalance. Predicted imbalance responses do not agree with the rotor measurements while crossing the critical speed, except for the lowest imbalance case. Gas pressurization through the bearings’ side ameliorates rotor subsynchronous motions and reduces the peak amplitudes at the critical speed. Posttest inspection reveal wear spots on the top foils and rotor surface.

Rotordynamics Performance of Hybrid Foil Bearing Under Forced Vibration Input

2017 ◽  
Author(s):  
Daejong Kim ◽  
Brian Nicholson ◽  
Lewis Rosado ◽  
Garry Givan
Keyword(s):  
Impulse Response ◽  
High Speed ◽  
Load Capacity ◽  
Supply System ◽  
Forced Response ◽  
Experimental Results ◽  
Lateral Acceleration ◽  
Foil Bearings ◽  
Foil Bearing ◽  
Gas Supply

Foil bearings are one type of hydrodynamic air/gas bearings but with a compliant bearing surface supported by structural material that provides stiffness and damping to the bearing. The hybrid foil bearing (HFB) in this paper is a combination of a traditional hydrodynamic foil bearing with externally-pressurized air/gas supply system to enhance load capacity during the start and to improve thermal stability of the bearing. The HFB is more suitable for relatively large and heavy rotors where rotor weight is comparable to the load capacity of the bearing at full speed and extra air/gas supply system is not a major added cost. With 4,448N∼22,240N thrust class turbine aircraft engines in mind, the test rotor is supported by HFB in one end and duplex rolling element bearings in the other end. This paper presents experimental work on HFB with diameter of 102mm performed at the US Air force Research Laboratory. Experimental works include: measurement of impulse response of the bearing to the external load corresponding to rotor’s lateral acceleration of 5.55g, forced response to external subsynchronous excitation, and high speed imbalance response. A non-linear rotordynamic simulation model was also applied to predict the impulse response and forced subsynchronous response. The simulation results agree well with experimental results. Based on the experimental results and subsequent simulations, an improved HFB design is also suggested for higher impulse load capability up to 10g and rotordynamics stability up to 30,000rpm under subsynchronous excitation.

Theoretical Study on Static Performance of Double-Bump Foil Bearings

2021 ◽  
Author(s):  
Fangcheng Xu ◽  
Jianhua Chu ◽  
Wenlin Luan ◽  
Guang Zhao
Keyword(s):  
Finite Element ◽  
Film Thickness ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Static Characteristics ◽  
Thrust Bearings ◽  
Foil Bearings ◽  
Foil Bearing ◽  
Static Performance ◽  
Initial Clearance

Abstract In this paper, single-bump foil models with different thickness and double-bump foil models with different initial clearances are established. The structural stiffness and equivalent viscous damping of double-bump foil and single-bump foil are analyzed by finite element simulation. The results show that the double-layer bump foil has variable stiffness and the displacement of the upper bump is greater than the initial gap when the two-layer bumps contact. A model for obtaining static characteristics of aerodynamic compliant foil thrust bearing is established on the basis of the stiffness characteristics of the double-bump foil. This paper solves gas Reynolds equation, the gas film thickness equation and the foil stiffness characteristic equation via the finite element method and the finite difference method. The static characteristics of the thrust bearings including the bearing pressure distribution, the gas film thickness and the friction power consumption have been obtained. The static characteristics of two kinds of foils have been compared and analyzed, and the effect of initial clearance on the static performance of double-bump foil bearings is studied. The results show that the double-bump foil structure can effectively improve the load capacity of thrust bearing. In addition, the static performance of double-bump foil thrust bearings is between the performance of the single-bump foil bearing and the double-bump foil bearing whose foil’s clearance is zero. The smaller the initial clearance is, the easier it will be to form a stable double-bump foil supporting structure.

Influence of geometric parameters on the bump foil bearing performance

2019 ◽  
Vol 234 (7) ◽  
pp. 1017-1026
Author(s):  
Sadanand Kulkarni ◽  
Soumendu Jana
Keyword(s):  
Carrying Capacity ◽  
High Speed ◽  
System Development ◽  
Load Capacity ◽  
Radial Clearance ◽  
Load Carrying Capacity ◽  
Foil Bearings ◽  
Foil Bearing ◽  
Load Carrying ◽  
Lift Off

High-speed rotating system development has drawn considerable attention of the researchers, in the recent past. Foil bearings are one of the major contenders for such applications, particularly for high speed and low load rotating systems. In foil bearings, process fluid or air is used as the working medium and no additional lubricant is required. It is known from the published literature that the load capacity of foil bearings depend on the operating speed, viscosity of the medium, clearance, and stiffness of the foil apart from the geometric dimensions of the bearing. In case of foil bearing with given dimensions, clearance governs the magnitude of pressure developed, whereas stiffness dictates the change in radial clearance under the generated pressure. This article deals with the effect of stiffness, clearance, and its interaction on the bump foil bearings load-carrying capacity. For this study, four sets of foil bearings of the same geometry with two levels of stiffness and clearance values are fabricated. Experiments are carried out following two factor-two level factorial design approach under constant load and in each case, the lift-off speed is measured. The experimental output is analyzed using statistical techniques to evaluate the influence of parameters under consideration. The results indicate that clearance has the maximum influence on the lift-off speed/ load-carrying capacity, followed by interaction effect and stiffness. A regression model is developed based on the experimental values and model is validated using error analysis technique.

Investigation of Structural Conformity in a Three-Pad Adaptive Air Foil Bearing With Regard to Active Control of Radial Clearance

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Hossein Sadri ◽  
Henning Schlums ◽  
Michael Sinapius
Keyword(s):  
Shape Control ◽  
Degrees Of Freedom ◽  
Load Capacity ◽  
Radial Clearance ◽  
Foil Bearings ◽  
Compliant Structure ◽  
Foil Bearing ◽  
Points Of View ◽  
Lift Off ◽  
Structural Conformity

Abstract Various solutions for the design of oil-free bearings are discussed in the literature. Adding hydrodynamic preload to the foil bearings by profiling the inner bore of the bearing is one of the most frequently investigated methods for improving the bearing stability and damping character of the entire system. However, this approach leads to a reduced load capacity and thus to an increased lift-off speed of the foil bearings. Observations of this kind lead to the presentation of various solutions for active bearing contour adjustment, which benefits from different profiles of the lubricant film. Most of these concepts use piezoelectric stack actuators to generate the required alternating force, although the influence of the stiffness of adaptive elements on bearing performance is not fully discussed in the literature. The focus of this study is on the investigation of structural conformity, i.e., the harmonization of stiffness with respect to the requirements for shape control and load capacity of an adaptive air foil bearing (AAFB). The result may be a basis for the consideration of additional degrees of freedom in any concept with shape control as the main design framework in interaction between the lubricant and compliant structure in an air foil bearing from both static and dynamic points of view.

Sign in / Sign up

Export Citation Format

Share Document