J0501-3-1 Studies on Separated Boundary Layers over High Lift Low-Pressure Turbine Airfoils : Effect of Freestream Turbulence

2009 ◽  
Vol 2009.7 (0) ◽  
pp. 23-24
Author(s):  
Ken-ichi FUNAZAKI ◽  
Nozomi TANAKA ◽  
Kazutoyo YAMADA ◽  
Yasuhiro CHIBA
Keyword(s):  
Boundary Layers ◽  
Low Pressure ◽  
Freestream Turbulence ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Turbine Airfoils

Numerical and Experimental Studies on Separated Boundary Layers Over Ultra-High Lift Low-Pressure Turbine Cascade Airfoils With Variable Solidity: Effects of Free-Stream Turbulence

2008 ◽  
Author(s):  
Ken-Ichi Funazaki ◽  
Kazutoyo Yamada ◽  
Yasuhiro Chiba ◽  
Nozomi Tanaka
Keyword(s):  
Boundary Layers ◽  
Free Stream ◽  
Separation Bubble ◽  
Experimental Studies ◽  
Low Pressure ◽  
Freestream Turbulence ◽  
High Lift ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine ◽  
Turbine Airfoils

This paper deals with LES investigation, along with measurements, on the interaction between inlet freestream turbulence and boundary layers with separation bubble over ultra-high lift low-pressure turbine airfoils. The cross section of the test airfoils is typical for highly-loaded LP turbines for civil aeroengines. The solidity of the cascade can be reduced by increasing the airfoil pitch by at least 25%, while maintaining the throat in the blade-to-blade passage. Reynolds number examined is 57,000, based on chord length and averaged exit velocity. Free-stream turbulence is about 0.85% (no grid condition) and 2.1% (with grid condition). Hot-wire probe measurements of the boundary layer are carried out to obtain time-averaged and time-resolved characteristics of the boundary layers under the influence of the freestream turbulence. A newly developed probe positioning tool, which is installed downstream of the cascade with minimal blockage, enables precise probe positioning along lines normal to the airfoil surface. Numerical analysis based on high-resolution LES (Large-Eddy Simulation) is executed to enhance the understanding of the flow field around the Ultra-High Lift and High Lift LP turbine airfoils. Emphasis is placed on the relationship of inherent instability of the shear layer of the separation bubble and the free-stream turbulence. Standard Smagorinsky model is employed for subgrid scale modeling. The flow solver used is an in-house code that was originally developed by one of the authors as FVM (Finite Volume Method)-based fully implicit and time-accurate Reynolds-Averaged Navier-Stokes code. Homogeneous isotropic turbulence created with SNGR (Stochastic Noise Generation and Radiation) method using von Karman-Pao turbulent energy spectrum is applied in the present study for the emulation of inlet turbulence.

scholarly journals Detailed Studies on Separated Boundary Layers Over Low-Pressure Turbine Airfoils Under Several High Lift Conditions: Effect of Freesteam Turbulence

2009 ◽  
Author(s):  
Ken-ichi Funazaki ◽  
Kazutoyo Yamada ◽  
Nozomi Tanaka ◽  
Yasuhiro Chiba
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Separation Bubble ◽  
Low Pressure ◽  
Scale Model ◽  
Freestream Turbulence ◽  
Suction Surface ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Turbine Airfoils

This paper deals with experimental investigation on the interaction between inlet freestream turbulence and boundary layers with separation bubble on a low-pressure turbine airfoil under several High Lift conditions. Solidity of the cascade can be reduced by increasing the airfoil pitch by 25%, while maintaining the throat in the blade-to-blade passage. Reynolds number examined is 57000, based on chord length and averaged exit velocity. Freestream turbulence intensity at the inlet is varied from 0.80% (no grid condition) to 2.1% by use of turbulence grid. Hot-wire probe measurements of the boundary layer on the suction surface for Low Pressure (LP) turbines rotor are carried out to obtain time-averaged and time-resolved characteristics of the boundary layers under the influence of the freestream turbulence. Frequency analysis extracts some important features of the unsteady behaviors of the boundary layer, including vortex formation and shedding. Numerical analysis based on high resolution Large Eddy Simulation is also executed to enhance the understanding on the flow field around the highly loaded turbine airfoils. Standard Smagorinsky model is employed as subgrid scale model. Emphasis of the simulation is placed on the relationship of inherent instability of the shear layer of the separation bubble and the freestream turbulence.

Redesign of High-Lift LP-Turbine Airfoils for Low Speed Testing

2010 ◽  
Author(s):  
Michele Marconcini ◽  
Filippo Rubechini ◽  
Roberto Pacciani ◽  
Andrea Arnone ◽  
Francesco Bertini
Keyword(s):  
Separated Flow ◽  
Low Pressure ◽  
High Lift ◽  
Low Speed ◽  
Low Pressure Turbine ◽  
Wide Range ◽  
Flow Configurations ◽  
Artificial Neural Network Ann ◽  
Lp Turbine ◽  
Turbine Airfoils

Low pressure turbine airfoils of the present generation usually operate at subsonic conditions, with exit Mach numbers of about 0.6. To reduce the costs of experimental programs it can be convenient to carry out measurements in low speed tunnels in order to determine the cascades performance. Generally speaking, low speed tests are usually carried out on airfoils with modified shape, in order to compensate for the effects of compressibility. A scaling procedure for high-lift, low pressure turbine airfoils to be studied in low speed conditions is presented and discussed. The proposed procedure is based on the matching of a prescribed blade load distribution between the low speed airfoil and the actual one. Such a requirement is fulfilled via an Artificial Neural Network (ANN) methodology and a detailed parameterization of the airfoil. A RANS solver is used to guide the redesign process. The comparison between high and low speed profiles is carried out, over a wide range of Reynolds numbers, by using a novel three-equation, transition-sensitive, turbulence model. Such a model is based on the coupling of an additional transport equation for the so-called laminar kinetic energy (LKE) with the Wilcox k–ω model and it has proven to be effective for transitional, separated-flow configurations of high-lift cascade flows.

Evaluation of RANS Transition Modeling for High Lift LPT Flows at Low Reynolds Number

2013 ◽  
Author(s):  
Kevin Keadle ◽  
Mark McQuilling
Keyword(s):  
Reynolds Number ◽  
Total Pressure ◽  
Current Model ◽  
Pressure Coefficient ◽  
Low Pressure ◽  
Two Dimensional ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Low Reynolds ◽  
Turbine Airfoils

High lift low pressure turbine airfoils have complex flow features that can require advanced modeling capabilities for accurate flow predictions. These features include separated flows and the transition from laminar to turbulent boundary layers. Recent applications of computational fluid dynamics based on the Reynolds-averaged Navier-Stokes formulation have included modeling for attached and separated flow transition mechanisms in the form of empirical correlations and two- or three-equation eddy viscosity models. This study uses the three-equation model of Walters and Cokljat [1] to simulate the flow around the Pack B and L2F low pressure turbine airfoils in a two-dimensional cascade arrangement at a Reynolds number of 25,000. This model includes a third equation for the development of pre-transitional laminar kinetic energy (LKE), and is an updated version of the Walters and Leylek [2] model. The aft-loaded Pack B has a nominal Zweifel loading coefficient of 1.13, and the front-loaded L2F has a nominal loading coefficient of 1.59. Results show the updated LKE model improves predicted accuracy of pressure coefficient and velocity profiles over its previous version as well as two-equation RANS models developed for separated and transitional flows. Transition onset behavior also compares favorably with experiment. However, the current model is not found suitable for wake total pressure loss predictions in two-dimensional simulations at extremely low Reynolds numbers due to the predicted coherency of suction side vortices generated in the separated shear layers which cause a local gain in wake total pressure.

An Investigation of Reynolds Lapse Rate for Highly Loaded Low Pressure Turbine Airfoils With Forward and Aft Loading

2011 ◽  
Author(s):  
M. Eric Lyall ◽  
Paul I. King ◽  
Rolf Sondergaard ◽  
John P. Clark ◽  
Mark W. McQuilling
Keyword(s):  
Reynolds Number ◽  
Eddy Viscosity ◽  
Low Pressure ◽  
Lapse Rate ◽  
Freestream Turbulence ◽  
Number Range ◽  
Low Pressure Turbine ◽  
Turbine Airfoils ◽  
Hot Film ◽  
Highly Loaded

This paper presents an experimental and computational study of the midspan low Reynolds number loss behavior for two highly loaded low pressure turbine airfoils, designated L2F and L2A, which are forward and aft loaded, respectively. Both airfoils were designed with incompressible Zweifel loading coefficients of 1.59. Computational predictions are provided using two codes, Fluent (with k-k1-ω model) and AFRL’s Turbine Design and Analysis System (TDAAS), each with a different eddy-viscosity RANS based turbulence model with transition capability. Experiments were conducted in a low speed wind tunnel to provide transition models for computational comparisons. The Reynolds number range based on axial chord and inlet velocity was 20,000 < Re < 100,000 with an inlet turbulence intensity of 3.1%. Predictions using TDAAS agreed well with the measured Reynolds lapse rate. Computations using Fluent however, predicted stall to occur at significantly higher Reynolds numbers as compared to experiment. Based on triple sensor hot-film measurements, Fluent’s premature stall behavior is likely the result of the eddy-viscosity hypothesis inadequately capturing anisotropic freestream turbulence effects. Furthermore, rapid distortion theory is considered as a possible analytical tool for studying freestream turbulence that influences transition near the suction surface of LPT airfoils. Comparisons with triple sensor hot-film measurements indicate that the technique is promising but more research is required to confirm its utility.

Measurements of Secondary Losses in a High-Lift Front-Loaded Turbine Cascade With the Implementation of Non-Axisymmetric Endwall Contouring

2009 ◽  
Author(s):  
D. C. Knezevici ◽  
S. A. Sjolander ◽  
T. J. Praisner ◽  
E. Allen-Bradley ◽  
E. A. Grover
Keyword(s):  
Secondary Flow ◽  
Low Pressure ◽  
Current Work ◽  
Test Facility ◽  
Test Case ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Baseline Test ◽  
Endwall Contouring ◽  
Turbine Airfoils

This paper is the second in a series from the same authors studying the mitigation of endwall losses using the low-speed linear cascade test facility at Carleton University. The previous paper documented the baseline test case for the study. The current work investigates the secondary flow in a cascade of more highly-loaded low-pressure turbine airfoils with and without the implementation of endwall profiling. This study is novel in two regards. First, the contouring is applied to low-pressure turbine airfoils, whereas studies conducted by other researchers have focused their endwall profiling efforts on the high-pressure turbine. Second, while previous researchers have optimized contouring designs for a given airfoil, the current work demonstrates the potential to open the design space by employing high-lift airfoils in conjunction with endwall contouring. Seven-hole pneumatic probe measurements taken within the blade passage and downstream of the trailing edge track the progression of the secondary flow and losses generated. The contouring divides the vorticity associated with the passage vortex into two weaker vortices, and reduces the secondary kinetic energy. Overall the secondary losses are reduced and the loss reduction is discussed with regards to changes in the flow physics. A detailed breakdown of the mixing losses further demonstrates the benefits of endwall contouring.

Effects of Periodic Wakes and Freestream Turbulence on Coherent Structures in Low-Pressure Turbine Boundary Layer

2012 ◽  
Author(s):  
Weihao Zhang ◽  
Zhengping Zou ◽  
Kun Zhou ◽  
Huoxing Liu ◽  
Jian Ye
Keyword(s):  
Boundary Layer ◽  
Coherent Structures ◽  
Low Pressure ◽  
Turbine Cascade ◽  
Freestream Turbulence ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Reduced Frequency ◽  
Large Eddy ◽  
Separation Bubbles

The effects of periodic wakes and inlet freestream turbulence intensity (FSTI) on coherent structures in the boundary layer of a high-lift low-pressure turbine cascade are studied in this paper. Large-eddy simulations (LES) are performed on T106D-EIZ profile at Reynolds number (Re) of 60,154 (based on the chord and outflow velocity). Eight cases, considering FSTI of 0, 2.5%, 5% and 10% as well as the wake reduced frequency (fr) of 0.67, 1.34 and 0.335, are conducted and discussed. The results show that the open separation could be compressed by freestream turbulence to a small extent, whereas, it could be replaced by separation bubbles under wake conditions. Stripe structures and turbulence spots appear in shear layer over the separation bubbles. The increments of wake frequency or FSTI can accelerate the transition progress which result in shorter separation bubbles, meanwhile, emphasize the turbulence spots.

An Investigation of Reynolds Lapse Rate for Highly Loaded Low Pressure Turbine Airfoils With Forward and Aft Loading

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
M. Eric Lyall ◽  
Paul I. King ◽  
Rolf Sondergaard ◽  
John P. Clark ◽  
Mark W. McQuilling
Keyword(s):  
Reynolds Number ◽  
Eddy Viscosity ◽  
Low Pressure ◽  
Lapse Rate ◽  
Freestream Turbulence ◽  
Number Range ◽  
Low Pressure Turbine ◽  
Turbine Airfoils ◽  
Hot Film ◽  
Highly Loaded

This paper presents an experimental and computational study of the midspan low Reynolds number loss behavior for two highly loaded low pressure turbine airfoils, designated L2F and L2A, which are forward and aft loaded, respectively. Both airfoils were designed with incompressible Zweifel loading coefficients of 1.59. Computational predictions are provided using two codes, Fluent (with k-kl-ω model) and AFRL’s Turbine Design and Analysis System (TDAAS), each with a different eddy-viscosity RANS based turbulence model with transition capability. Experiments were conducted in a low speed wind tunnel to provide transition models for computational comparisons. The Reynolds number range based on axial chord and inlet velocity was 20,000 < Re < 100,000 with an inlet turbulence intensity of 3.1%. Predictions using TDAAS agreed well with the measured Reynolds lapse rate. Computations using Fluent however, predicted stall to occur at significantly higher Reynolds numbers as compared to experiment. Based on triple sensor hot-film measurements, Fluent’s premature stall behavior is likely the result of the eddy-viscosity hypothesis inadequately capturing anisotropic freestream turbulence effects. Furthermore, rapid distortion theory is considered as a possible analytical tool for studying freestream turbulence that influences transition near the suction surface of LPT airfoils. Comparisons with triple sensor hot-film measurements indicate that the technique is promising but more research is required to confirm its utility.

Sign in / Sign up

Export Citation Format

Share Document