105 Experimental Study of the Flow Field around a Straight-Wing Vertical-Axis Wind Turbine Model

2011 ◽  
Vol 2011.46 (0) ◽  
pp. 14-15
Author(s):  
Tatsuya SHODA ◽  
Yuko SATO ◽  
Masaya SHIGETA ◽  
Seiichiro IZAWA ◽  
Yu FUKUNISHI
Keyword(s):  
Experimental Study ◽  
Flow Field ◽  
Wind Turbine ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Straight Wing ◽  
Turbine Model

scholarly journals A Study of a Darrieus Vertical Axis Wind Turbine with a guiding nozzle

2020 ◽  
Vol 207 ◽  
pp. 02011
Author(s):  
Valentin Obretenov ◽  
Rossen Tliev
Keyword(s):  
Experimental Study ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Pitch Angle ◽  
Vertical Axis ◽  
Performance Characteristics ◽  
Vertical Axis Wind Turbine ◽  
Pilot Studies ◽  
Generalized Characteristics ◽  
Turbine Model

This paper presents the results from an experimental study of a Vertical Axis Wind turbine model with a guiding nozzle. The geometry of the nozzle is synthesized by an original methodology. The performance characteristics of the turbine are investigated when changing the number of the blades and their pitch angle. The obtained results allow us to generate generalized characteristics that can be used in the design of new turbines of this type. The results of the pilot studies showing higher efficiency than the classical Darrieus wind turbines (up to 50 % which is close to the Betz limit).

scholarly journals A Computational and Experimental Study of a Small-Scale Flat-Shaped Vertical Axis Wind Turbine

2018 ◽  
Vol 7 (4.35) ◽  
pp. 946
Author(s):  
NF. Kadir ◽  
H. Mohamed ◽  
A. Manap
Keyword(s):  
Experimental Study ◽  
Wind Speed ◽  
Wind Turbine ◽  
Turbine Blades ◽  
Vertical Axis ◽  
Angular Speed ◽  
Small Scale ◽  
Vertical Axis Wind Turbine ◽  
Percentage Difference ◽  
Turbine Model

This paper focuses on a computational and experimental study of flat-shaped turbine blades for a small scale Vertical Axis Wind Turbine (VAWT). In the computational analysis, a 2-Dimensional (2D) wind turbine model with three flat blades was designed using Ansys Flu-ent, which is computational fluid dynamics (CFD) software. The wind speed around the blades was simulated in a range of 3 m/s to 8 m/s. Velocity and pressure distributions of the airflow around the blades were then observed. Pressures acting on the blades surface were then averaged and used to estimate the angular speed of the wind turbine model using the principles of torque and moment of inertia. A small-scale prototype was designed, fabricated and tested to validate the simulation result. Testing results show that the wind turbine prototype can rotate with an average speed of 148.8 rpm when having a 3.27 m/s wind speed. At the similar wind speed, the simulation result has estimated the angular speed to be 119 rpm. The percentage difference of the angular speed is about 20%. .  

Investigation of aerodynamic forces and flow field of an H-type vertical axis wind turbine based on bionic airfoil

Energy ◽  
2021 ◽  
pp. 122999
Author(s):  
Yanfeng Zhang ◽  
Zhiping Guo ◽  
Xinyu Zhu ◽  
Yuan Li ◽  
Xiaowen Song ◽  
...  
Keyword(s):  
Flow Field ◽  
Wind Turbine ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Aerodynamic Forces ◽  
Bionic Airfoil

scholarly journals An experimental study of the optimal design parameters of a wind power tower used to improve the performance of vertical axis wind turbines

2018 ◽  
Vol 10 (9) ◽  
pp. 168781401879954
Author(s):  
Soo-Yong Cho ◽  
Sang-Kyu Choi ◽  
Jin-Gyun Kim ◽  
Chong-Hyun Cho
Keyword(s):  
Experimental Study ◽  
Optimal Design ◽  
Wind Turbine ◽  
Wind Power ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Design Parameters ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines

In order to augment the performance of vertical axis wind turbines, wind power towers have been used because they increase the frontal area. Typically, the wind power tower is installed as a circular column around a vertical axis wind turbine because the vertical axis wind turbine should be operated in an omnidirectional wind. As a result, the performance of the vertical axis wind turbine depends on the design parameters of the wind power tower. An experimental study was conducted in a wind tunnel to investigate the optimal design parameters of the wind power tower. Three different sizes of guide walls were applied to test with various wind power tower design parameters. The tested vertical axis wind turbine consisted of three blades of the NACA0018 profile and its solidity was 0.5. In order to simulate the operation in omnidirectional winds, the wind power tower was fabricated to be rotated. The performance of the vertical axis wind turbine was severely varied depending on the azimuthal location of the wind power tower. Comparison of the performance of the vertical axis wind turbine was performed based on the power coefficient obtained by averaging for the one periodic azimuth angle. The optimal design parameters were estimated using the results obtained under equal experimental conditions. When the non-dimensional inner gap was 0.3, the performance of the vertical axis wind turbine was better than any other gaps.

scholarly journals Experimental investigation of a variable geometry vertical axis wind turbine

2020 ◽  
pp. 0309524X2093513
Author(s):  
Simon A Prince ◽  
Carmine Badalamenti ◽  
Dimitar Georgiev
Keyword(s):  
Experimental Study ◽  
Wind Turbine ◽  
Pitch Angle ◽  
Vertical Axis ◽  
Reynolds Numbers ◽  
Variable Geometry ◽  
Vertical Axis Wind Turbine ◽  
Wind Tunnel Experiments ◽  
Electrical Generator ◽  
Turbine Design

An experimental study is presented on the performance of a vertical axis wind turbine with variable blade geometry of the design developed by Austin Farrah. This is experimentally compared with the performance of a correspondingly sized Bach-type Savonius turbine using the same electrical generator and measurement instrumentation in a wind tunnel. Experiments were performed for Reynolds numbers, based on blade chord, in the range 5 × 103 to 1 × 105, and for blade settings between −40° and +40o. The study shows that for the tip speed ratios that have been investigated, the Farrah vertical axis wind turbine design can only marginally outperform a corresponding two-bladed Bach-type Savonius turbine and then only when its blades are set to 40° pitch angle. The presence of a small inner cylinder, which rotates with the turbine, does not enhance its performance due to the fact that it is immersed in an extensive column of relatively static air.

Numerical Simulation of the Aerodynamic Performance of a H-Type Wind Turbine during Self-Starting

2014 ◽  
Vol 529 ◽  
pp. 296-302 ◽  
Author(s):  
Wei Zuo ◽  
Shun Kang
Keyword(s):  
Flow Field ◽  
Wind Turbine ◽  
Pitch Angle ◽  
Turbulence Modeling ◽  
Vertical Axis ◽  
Aerodynamic Performance ◽  
Time Dependent ◽  
Two Dimensional ◽  
Vertical Axis Wind Turbine ◽  
Sst Turbulence Model

The aerodynamic performance and the bypass flow field of a vertical axis wind turbine under self-starting are investigated using CFD simulations in this paper. The influence of pitch angle variations on the performance of the wind turbine during self-starting is presented. A two-dimensional model of the wind turbine with three blades is employed. A commercial software FlowVision is employed in this paper, which uses dynamic Cartesian grid. The SST turbulence model is used for turbulence modeling, which assumes the flow full turbulent. Based on the comparison between the computed time-dependent variations of the rotation speed with the experimental data, the time-dependent variations of the torque are presented. The characteristics of self-starting of the wind turbine are analyzed with the pitch angle of 0o、-2oand 2o. The influence of pitch angle variations on two-dimensional unsteady viscous flow field through velocity contours is discussed in detail.

Sign in / Sign up

Export Citation Format

Share Document