Nondestructive NIR and NIT Determination of Protein, Fat, and Water in Plastic-Wrapped, Homogenized Meat

1992 ◽  
Vol 46 (11) ◽  
pp. 1685-1694 ◽  
Author(s):  
Tomas Isaksson ◽  
Charles E. Miller ◽  
Tormod Næs

In this work, the abilities of near-infrared diffuse reflectance (NIR) and transmittance (NIT) spectroscopy to noninvasively determine the protein, fat, and water contents of plastic-wrapped homogenized meat are evaluated. One hundred homogenized beef samples, ranging from 1 to 23% fat, wrapped in polyamide/polyethylene laminates, were used. Results of multivariate calibration and prediction for protein, fat, and water contents are presented. The optimal test set prediction errors (root mean square error of prediction, RMSEP), obtained with the use of the principal component regression method with NIR data, were 0.45, 0.29 and 0.50 weight % for protein, fat, and water, respectively, for plastic-wrapped meat (compared to 0.40, 0.28 and 0.45 wt % for unwrapped meat). The optimal prediction errors for the NIT method were 0.31, 0.52 and 0.42 wt % for protein, fat, and water, respectively, for plastic-wrapped meat samples (compared to 0.27, 0.38, and 0.37 wt % for unwrapped meat). We can conclude that the addition of the laminate only slightly reduced the abilities of the NIR and NIT method to predict protein, fat, and water contents in homogenized meat.

1988 ◽  
Vol 42 (7) ◽  
pp. 1273-1284 ◽  
Author(s):  
Tomas Isaksson ◽  
Tormod Næs

Near-infrared (NIR) reflectance spectra of five different food products were measured. The spectra were transformed by multiplicative scatter correction (MSC). Principal component regression (PCR) was performed, on both scatter-corrected and uncorrected spectra. Calibration and prediction were performed for four food constituents: protein, fat, water, and carbohydrates. All regressions gave lower prediction errors (7–68% improvement) by the use of MSC spectra than by the use of uncorrected absorbance spectra. One of these data sets was studied in more detail to clarify the effects of the MSC, by using PCR score, residual, and leverage plots. The improvement by using nonlinear regression methods is indicated.


The Analyst ◽  
1994 ◽  
Vol 119 (7) ◽  
pp. 1537-1540 ◽  
Author(s):  
Mercedes Jiménez Arrabal ◽  
Pablo Valiente González ◽  
Concepción Caro Gámez ◽  
Antonio Sánchez Misiego ◽  
Arsenio Muñoz de la Peña

2016 ◽  
Vol 51 (4) ◽  
pp. 297-306 ◽  
Author(s):  
SS Israt ◽  
MN Uddin ◽  
RA Jahan ◽  
MM Karim

The combination of furosemide (furo) and spironolactone (spiro) is very effective in the treatment of heart failure. In that case, maintaining good quality of these drugs in commercial tablets is must. Therefore, a simple, economical, precise and accurate method, i.e; chemometric assisted UV spectroscopy, for simultaneous determination of furosemide and spironolactone in combined dosage form has been developed. In this study, principal component regression (PCR) has been reported for this purpose. A calibration set of 36 mixture solutions containing furosemide and spironolactone in methanol in the concentration range of 2.0-12.0 ?g/ml and 5.0-30.0 ?g/ml respectively has been prepared by means of an orthogonal experimental design. The absorbance data for the concentration set have been obtained by direct measurement in UV spectrophotometer at 101 wavelength points in the spectral region of 200-300 nm for the zero order spectra. The chemometric technique is also successfully applied to available pharmaceutical formulations, tablets, with no interference from excipients. The analytical performances of principal component regression are characterized by relative prediction errors and recoveries (%). The good recoveries obtained in this case proved that the proposed chemometric technique could be applied efficiently in the quality control of the studied drugs simultaneously in their mixture as well as in the commercial dosage form with satisfactory precision and accuracy as alternative analysis tools.Bangladesh J. Sci. Ind. Res. 51(4), 297-306, 2016


1993 ◽  
Vol 47 (2) ◽  
pp. 222-228 ◽  
Author(s):  
Charles E. Miller

The ability of near-infrared (NIR) spectroscopy, combined with principal component regression (PCR), to nondestructively determine the blend ratio of high-density polyethylene (HDPE) and low-density polyethylene (LDPE) in extruded films is demonstrated. Results indicate that the NIR spectrum in the region 2100 to 2500 nm can be used to determine the HDPE mass percentage of 60–80- μm-thick film samples to within 2.5%, over a range of 0 to 100%. NIR spectral effects from scattering are important for the determination of the HDPE % for HDPE contents above 50%, and spectral effects from changes in the methyl group concentration and perhaps the PE crystallinity are important for the determination of the HDPE % for HDPE contents below 50%. In addition, a large variation between the spectra of replicate samples, probably caused by variations in the degree or direction of molecular orientation in the samples, was observed.


2002 ◽  
Vol 56 (12) ◽  
pp. 1593-1599 ◽  
Author(s):  
Peter Snoer Jensen ◽  
Jimmy Bak

This study investigates the use of a dual-beam, optical null, FT-IR spectrometer to measure trace organic components in aqueous solutions in the combination band region 5000–4000 cm−1. The spectrometer may be used for both single- and dual-beam measurements, thereby facilitating comparison of these two modes of operation. The concentrations of aqueous solutions of urea and glucose in the ranges 0–40 mg/dL and 0–250 mg/dL, respectively, were determined by principal component regression using both modes. The dual-beam technique eliminated instrumental variations present in the single-beam measurements that must be taken into account when quantifying trace components from single-beam spectra. The data obtained with the dual-beam technique resulted in more stable calibration models based on principal component regression. These calibration models need fewer factors and yield lower prediction errors than those based on traditional single-beam data.


2018 ◽  
Vol 101 (4) ◽  
pp. 1001-1007
Author(s):  
Eman S Elzanfaly ◽  
Hala E Zaazaa ◽  
Aya T Soudi ◽  
Maissa Y Salem

Abstract Two multivariate validated spectrophotometric methods, namely partial least-squares (PLS) and principal component regression (PCR), were developed and validated for the determination of ibuprofen and famotidine in presence of famotidine degradation products and ibuprofen impurity (4-isobutylacetophenone). A calibration set was prepared in which the two drugs together with the degradation products and impurity were modeled using a multilevel multifactor design. This calibration set was used to build the PLS and PCR models. The proposed models successfully predicted the concentrations of both drugs in validation samples, with low root mean square error of cross validation (RMSECV) percentage. The method was validated by the estimate of the figures of merit depending on the net analyte signal. The results of the two models showed that the simultaneous determination of both drugs could be performed in the concentration ranges of 100–500 µg/mL for ibuprofen and 5–25 µg/mL for famotidine. The proposed multivariate calibration methods were applied for the determination of ibuprofen and famotidine in their pharmaceutical formulation, and the results were verified by the standard addition technique.


Sign in / Sign up

Export Citation Format

Share Document