Performance Analysis of FBG WDM System using Different Optical Amplifiers

2018 ◽  
Vol 0 (0) ◽  
Author(s):  
Suraj Jain ◽  
Chakresh Kumar
Keyword(s):  
Wavelength Division Multiplexing ◽  
Optical Amplifiers ◽  
Fiber Amplifier ◽  
Optical Amplifier ◽  
Q Factor ◽  
Erbium Doped Fiber Amplifier ◽  
Wavelength Division ◽  
Raman Amplifier ◽  
Erbium Doped ◽  
Channel Wavelength

AbstractThis paper aims to analyze the performance of FBG 60 channel wavelength-division multiplexing system using different optical amplifiers namely RAMAN, erbium-doped fiber amplifier (EDFA) and semiconductor optical amplifier (SOA) separately at 10 Gbps data rate up to a fiber length of 280 km. Based upon the results, the performance of the three amplifiers has been compared on the basis of multiple performance parameters. It is seen that EDFA simulates good results in terms of bit error rate (BER) up to a fiber distance of approximately 80 km and Q factor up to a distance of approximately 90 km among all the three amplifiers. However, power received is least in EDFA. RAMAN amplifier provides a better Q factor after the fiber distance of approximately 90 km and a better BER after the fiber distance of approximately 80 km compared to the other three amplifiers. SOA shows better results in terms of power received up to a fiber distance of approximately 100 km. RAMAN amplifier provides better output power after a distance of 100 km. Eye diagrams and power spectrums of the network with different optical amplifiers has also been analyzed.

Investigations of Different Amplifiers in 16 × 40 Gb/S WDM System

2019 ◽  
Vol 40 (4) ◽  
pp. 341-346
Author(s):  
Kulwinder Singh ◽  
Karan Goel ◽  
Kamaljit Singh Bhatia ◽  
Hardeep Singh Ryait
Keyword(s):  
Wavelength Division Multiplexing ◽  
Fiber Amplifier ◽  
Optical Amplifier ◽  
Fiber Amplifiers ◽  
Erbium Doped Fiber Amplifier ◽  
Wavelength Division ◽  
Transmission Distance ◽  
Erbium Doped ◽  
Eye Opening ◽  
Eye Closure

Abstract Different fiber amplifiers such as semiconductor optical amplifier, erbium-doped fiber amplifier and erbium ytterbium-co-doped fiber amplifier (EYCDFA) are investigated for 16×40 GB/s wavelength division multiplexing system. Various performance parameters including Q-factor, bit error rate, jitter, eye opening and eye closure are observed and analyzed. It is reported that EYCDFA is a better choice among the tested amplifiers. The proposed system is also investigated in terms of transmission distance.

Study the Performance of Various Optical Amplifiers for 80 Channels WDM System Using Attenuator

2018 ◽  
Vol 0 (0) ◽  
Author(s):  
◽  
Chakresh Kumar
Keyword(s):  
Wavelength Division Multiplexing ◽  
Semiconductor Optical Amplifier ◽  
Optical Amplifiers ◽  
Optical Amplifier ◽  
Data Rate ◽  
Q Factor ◽  
Eye Diagram ◽  
Wavelength Division ◽  
Transmission Distance ◽  
Erbium Doped

AbstractIn this paper we have study the performance of different optical amplifiers (Erbium doped amplifier (EDFA), RAMAN amplifier, and semiconductor optical amplifier (SOA)) for 80 channels wavelength division multiplexing (WDM) system with the data rate at 10 Gbps data rate for the transmission distance of 280 km After getting the results of these amplifiers the performance of these has to be compared The Q-factor values achieved better in EDFA as compared to SOA and RAMAN. While the BER getting good in SOA as compared with other amplifiers but in EDFA after 200 km it goes saturated, the Power achieved at the power estimator is getting better in EDFA optical amplifier while in other amplifier it achieved negative. At the end it is also study the Power with frequency in THz and the Eye Diagram of such amplifiers results.

Performance Evaluation of Proposed WDM Optical Link Using EDFA and FBG Combination

2019 ◽  
Vol 40 (2) ◽  
pp. 101-107 ◽  
Author(s):  
Deepti Ahlawat ◽  
Payal Arora ◽  
Suresh Kumar
Keyword(s):  
Wavelength Division Multiplexing ◽  
Chromatic Dispersion ◽  
Fiber Amplifier ◽  
Q Factor ◽  
Wavelength Band ◽  
Modulation Formats ◽  
Erbium Doped Fiber Amplifier ◽  
Wavelength Division ◽  
Modulation Format ◽  
Erbium Doped

Abstract Analysis of wavelength division multiplexing (WDM) system utilizing erbium-doped fiber amplifier (EDFA) has been carried out by many researchers. In this paper, the performance analysis of 8-channel WDM system utilizing EDFA and fiber Bragg grating (FBG) combination is carried out in a wavelength band 1546–1552 nm at 10 Gbps. The performance of three apodization functions (Uniform, Gaussian and Tanh) of FBG is compared using return-to-zero (RZ) and non-return-to-zero modulation formats at fiber lengths 50, 60, 70 and 80 km. Also, the performance of FBG is compared for both aspects: with chirp and without chirp for grating lengths 5–10 mm. The Gaussian apodized and linearly chirped FBG outperformed the other two in compensating chromatic dispersion. Optimum values of Q-factor are also obtained using linearly chirped FBG with RZ modulation format at 10 mm of grating length.

scholarly journals Performance Evaluation of Different Optical Amplifiers in Spectrum Sliced Free Space Optical Link

2019 ◽  
Vol 41 (1) ◽  
pp. 9-14 ◽  
Author(s):  
Aditi Thakur ◽  
Shaina Nagpal
Keyword(s):  
Wavelength Division Multiplexing ◽  
Free Space ◽  
High Speed ◽  
Optical Amplifiers ◽  
Fiber Amplifier ◽  
Optical Amplifier ◽  
Free Space Optical ◽  
Erbium Doped Fiber Amplifier ◽  
Wavelength Division ◽  
Space Optics

Abstract Free space optics (FSO) is well-competent and premier technology to cater the high speed services in different geographical areas such as hilly areas and inter building network. In this paper, we successfully demonstrated the spectrum sliced wavelength division multiplexed FSO system. In order to make system bandwidth efficient, frequency spacing of 75 GHz is taken among the wavelength division multiplexing (WDM) channels. Carrier spectrum broadening is achieved for spectrum slicing through the nonlinearity called self-phase modulation. Moreover, requirement of multiple laser sources is eliminated. However, in conventional WDM systems, n numbers of lasers are needed to generate n WDM channels. To strengthen the signal in this FSO system, three optical amplifiers are scrutinized such as erbium-doped fiber amplifier (EDFA), semiconductor optical amplifier (SOA) and Raman amplifier in terms of Q-factor and bit error rate (BER). Results revealed that EDFA is best amplifier in proposed SS-WDM-FSO system.

Effect of Optical Amplifiers on the Performance of SCM Radio over Fiber Systems

2015 ◽  
Vol 36 (3) ◽  
Author(s):  
Sakshi Sharma ◽  
Kamaljeet Singh Bhatia ◽  
Harsimrat Kaur
Keyword(s):  
Semiconductor Optical Amplifier ◽  
Optical Amplifiers ◽  
Fiber Amplifier ◽  
Optical Amplifier ◽  
Radio Over Fiber ◽  
Optimal Performance ◽  
Erbium Doped Fiber Amplifier ◽  
Raman Amplifier ◽  
Erbium Doped ◽  
Subcarrier Multiplexing

AbstractA bidirectional subcarrier multiplexing (SCM)-radio-over-fiber(RoF) network is proposed. In this paper, SCM RoFlink is analyzed with and without optical amplifier. The response of the system is studied for semiconductor optical amplifier (SOA), erbium-doped fiber amplifier (EDFA) and Raman amplifier. The results for the same are compared and then the appropriate amplifier is selected and the required gain for the optimal performance of the system is reported.

scholarly journals Design of a Hybrid Optical amplifier for 64 DWDM Channels network by using EDFA and Raman Amplifier

2017 ◽  
Vol 5 (4) ◽  
pp. 18-23
Author(s):  
Bandana Mallick ◽  
Bibhu Prasad ◽  
Dr. Krishna Chandra Patra
Keyword(s):  
Wavelength Division Multiplexing ◽  
Fiber Amplifier ◽  
Optical Amplifier ◽  
Input Power ◽  
Fiber Amplifiers ◽  
Wavelength Division ◽  
Raman Amplifier ◽  
Optical Fiber Amplifier ◽  
Erbium Doped ◽  
Different Types

In this paper a hybrid amplifier EDFA-RAMAN DWDM transmission system is proposed and demonstrated. A new hybrid two-stage optical fiber amplifier for dense wavelength division multiplexing (DWDM) network is observed. The hybrid amplifier is cascaded erbium- doped fiber amplifiers (EDFA) & Raman amplifier which provide a nearly flat gain over 80 nm. The hybrid amplifier has been modeled using an Optic-System version 14 on a DWDM transmission. In this paper we compare Q-factor at different input power i.e. at 0db and at 10 db. Here two different types of apodized function (Uniform & Gaussian) are selected as fiber Bragg grating parameters and system performance is analyzed. Performance of the system is analyzed by using BER analyzer.

Link Power Level Improvements in an Amplified 8-Channel CWDM System with Hybrid EDFA-SOA Pre-Amplifier

2015 ◽  
Vol 799-800 ◽  
pp. 1361-1365
Author(s):  
Khadijah Ismail ◽  
P.S. Menon ◽  
Sahbudin Shaari ◽  
Abang Annuar Ehsan ◽  
Norhana Arsad ◽  
...  
Keyword(s):  
Wavelength Division Multiplexing ◽  
Power Level ◽  
Fiber Amplifier ◽  
Optical Amplifier ◽  
Erbium Doped Fiber Amplifier ◽  
Wavelength Division ◽  
Erbium Doped ◽  
Gain Measurement ◽  
Transmission Link ◽  
Coarse Wavelength Division Multiplexing

The link power improvement in a coarse wavelength division multiplexing (CWDM) system which is transmitted using a hybrid erbium-doped fiber amplifier (EDFA) and semiconductor optical amplifier (SOA) scheme as a pre-amplifier, is discussed. The network is designed for amplifying 8 CWDM channels ranging from 1471 nm to 1611 nm. The hybrid amplifiers’ gain measurement is obtained from experimental work with gain peak at 22 dB which is observed at 1531 nm. The amplifiers also caused power increment of 5.06 dB in the transmission link before the signal is split individually at the receiving end. Based on the higher gain peaks and power spectrum at 1531 nm and 1551 nm wavelengths, the proposed amplified link would be useful for the transmission of video applications.

scholarly journals Comparative Analysis of Erbium Doped Fiber Amplifier (EDFA) and Raman Optical Amplifier (ROA) in Nonlinear-CWDM System

2018 ◽  
Vol 10 (3) ◽  
pp. 144
Author(s):  
Dodi Zulherman ◽  
Sri Utami ◽  
Fahmi Fahmi
Keyword(s):  
Wavelength Division Multiplexing ◽  
System Performance ◽  
Fiber Amplifier ◽  
Optical Amplifier ◽  
High Rate ◽  
Telecommunication Service ◽  
Raman Amplification ◽  
Erbium Doped Fiber Amplifier ◽  
Large Bandwidth ◽  
Erbium Doped

The massive demands for high-rate application drove the telecommunication service to use large bandwidth capacity. The Coarse Wavelength Division Multiplexing (CWDM), a common use in Metro-WDM, can be a solution to provide large bandwidth in optical communications. In a communications system, there are attenuation and nonlinear effect decreasing the system performance. In order to overcome the limitation imposed by electrical regeneration to maintain system performance, a means of optical amplification was sought. In this paper presents the comparison of two competing technologies emerged: Erbium Doped Fiber Amplifier (EDFA) and Raman Optical Amplifier (ROA) to overcome the attenuation in the nonlinear system. We designed the CWDM system using 8 channels with 20 nm channel spacing and 60 km length. The result was conducted by varying the CW Laser power using -8, -6, -4, -2, 0, 2, 4, and 6 dBm. Based on the result of the research, raman amplification can maintain the BER and the Q-factor of the CWDM system better than EDFA. In addition, the received power in raman amplification larger than that received in EDFA. In conclusion,a CWDM system using ROA amplifier has better performance for the system than using EDFA amplifier.

Comparative Performance of Modulation Formats using RAMAN-EDFA Hybrid Optical Amplifier in Fiber Optic Communication System

2017 ◽  
Vol 38 (2) ◽  
Author(s):  
Garima Arora ◽  
Sanjeev Dewra
Keyword(s):  
Wavelength Division Multiplexing ◽  
Fiber Amplifier ◽  
Optical Amplifier ◽  
Comparative Performance ◽  
Modulation Formats ◽  
Erbium Doped Fiber Amplifier ◽  
Wavelength Division ◽  
Transmission Length ◽  
Fiber Optic Communication ◽  
Optic Communication

AbstractThis paper presents the comparison of various modulation formats for 64×10 Gbps dense wavelength division multiplexing system using Raman–erbium-doped fiber amplifier optical amplifier with 100 GHz interval. We evaluate the suitability of various data formats like return-to-zero (RZ) raised cosine (RC), RZ rectangular (Rect), non-return-to-zero (NRZ) RC and NRZ-Rect for an optical transmission link. The results have been carried out by evaluating the value of quality factor, bit error rate (BER) and average opening of an eye. It is found that using NRZ-Rect data format, the signal can travel up to transmission length of 234 km with acceptable BER (1.10e

Sign in / Sign up

Export Citation Format

Share Document