scholarly journals Experimental Estimation of Design and Drilling Regime Option Influence on Drilling Tool Dynamics

2021 ◽  
Vol 43 (5) ◽  
pp. 689-712
Author(s):  
V. M. Moysyshyn ◽  
◽  
М. V. Lyskanych ◽  
L. V. Borysevych ◽  
O. Yu. Vytyaz ◽  
...  
Keyword(s):  
Drilling Tool ◽  
Experimental Estimation ◽  
Tool Dynamics

MODELING OF THE DYNAMIC PROCESS RELEASE OF STUCK DRILLING TOOLS BY HYDRO-PULSE METHOD

2019 ◽  
pp. 94-103
Author(s):  
K. H. Levchyk ◽  
M. V. Shcherbyna
Keyword(s):  
Mathematical Model ◽  
Dynamic Process ◽  
Drilling Fluid ◽  
Pulse Method ◽  
Geometrical Parameters ◽  
Technical Solution ◽  
Rock Layer ◽  
Drilling Tool ◽  
Drilling Tools ◽  
Drill Pipes

A technical solution is proposed for the elimination the grabbing of drilling tool, based on the use of energy due to the circulation of the drilling fluid. The expediency eliminating the grabbing drilling tool using the hydro-impulse method is substantiated. A method of drawing up a mathematical model for the dynamic process of a grabbing string of drill pipes in the case of perturbation of hydro-impulse oscillations in the area of the productive rock layer is developed. The law of longitudinal displacements arising in the trapped string is obtained, which allows choosing the optimal geometrical parameters of the passage channels and the frequency rotational of shutter for these channels. Recommendations for using this method for practical use have been systematized.

ANALYSIS OF STAND RESEARCH RESULTS OF AXIAL DYNAMIC FORCE IN DRILLING BY THREE ROLLER CONE BIT

2019 ◽  
pp. 81-93
Author(s):  
В. М. Мойсишин ◽  
M. V. Lyskanych ◽  
R. A. Zhovniruk ◽  
Ye. P. Majkovych
Keyword(s):  
Low Frequency ◽  
Maximum Energy ◽  
Dynamic Force ◽  
Low Frequency Oscillation ◽  
Drilling Tool ◽  
Rock Destruction ◽  
Frequency Components ◽  
Harmonic Components ◽  
Experimental Values ◽  
Harmful Effects

The purpose of the proposed article is to establish the causes of oscillations of drilling tool and the basic laws of the distribution of the total energy of the process of changing the axial dynamic force over frequencies of spectrum. Variable factors during experiments on the classical plan were the rigidity of drilling tool and the hardness of the rock. According to the results of research, the main power of the process of change of axial dynamic force during drilling of three roller cone bits is in the frequency range 0-32 Hz in which three harmonic frequency components are allocated which correspond to the theoretical values of low-frequency and gear oscillations of the chisel and proper oscillations of the bit. The experimental values of frequencies of harmonic components of energy and normalized spectrum as well as the magnitude of the dispersion of the axial dynamic force and its normalized values at these frequencies are presented. It has been found that with decreasing rigidity of the drilling tool maximum energy of axial dynamic force moves from the low-frequency oscillation region to the tooth oscillation area, intensifying the process of rock destruction and, at the same time, protecting the tool from the harmful effects of the vibrations of the bit. Reducing the rigidity of the drilling tool protects the bit from the harmful effects of the vibrations generated by the stand. The energy reductions in these fluctuations range from 47 to 77%.

scholarly journals Kinematics and dynamics analysis of new rotary-percussive PDM drilling tool

2021 ◽  
pp. 146134842198915
Author(s):  
Jialin Tian ◽  
Xuehua Hu ◽  
Liming Dai ◽  
Lin Yang ◽  
Yi Yang ◽  
...  
Keyword(s):  
Drill String ◽  
Structure Design ◽  
Drilling Process ◽  
Analysis Model ◽  
Drilling Tool ◽  
Stick Slip ◽  
Rate Of Penetration ◽  
Bottom Hole ◽  
Bottom Hole Assembly ◽  
The Impact

This paper presents a new drilling tool with multidirectional and controllable vibrations for enhancing the drilling rate of penetration and reducing the wellbore friction in complex well structure. Based on the structure design, the working mechanism is analyzed in downhole conditions. Then, combined with the impact theory and the drilling process, the theoretical models including the various impact forces are established. Also, to study the downhole performance, the bottom hole assembly dynamics characteristics in new condition are discussed. Moreover, to study the influence of key parameters on the impact force, the parabolic effect of the tool and the rebound of the drill string were considered, and the kinematics and mechanical properties of the new tool under working conditions were calculated. For the importance of the roller as a vibration generator, the displacement trajectory of the roller under different rotating speed and weight on bit was compared and analyzed. The reliable and accuracy of the theoretical model were verified by comparing the calculation results and experimental test results. The results show that the new design can produce a continuous and stable periodic impact. By adjusting the design parameter matching to the working condition, the bottom hole assembly with the new tool can improve the rate of penetration and reduce the wellbore friction or drilling stick-slip with benign vibration. The analysis model can also be used for a similar method or design just by changing the relative parameters. The research and results can provide references for enhancing drilling efficiency and safe production.

Sign in / Sign up

Export Citation Format

Share Document