Highly oriented thin films of cubic zirconia on sapphire through grain growth seeding

1991 ◽  
Vol 6 (11) ◽  
pp. 2387-2392 ◽  
Author(s):  
K.T. Miller ◽  
F.F. Lange
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Thin Film Deposition ◽  
Epitaxial Films ◽  
Film Deposition ◽  
Material System ◽  
Polycrystalline Thin Film ◽  
Process Step ◽  
Heat Treated ◽  
Deposition Techniques

A two-step process has been developed to form highly oriented thin films in material systems with dissimilar crystal structures and interatomic spacings. This processing method utilizes current polycrystalline thin film deposition techniques. In this method, a polycrystalline thin film is first deposited and heat treated to promote its breakup into isolated grains. The breakup process favors those grains that have a low substrate interfacial energy and so produces a film of highly oriented but isolated grains. In the second process step, another polycrystalline thin film is deposited. The remnant grains act as seeds for the growth of a highly oriented thin film. The process is demonstrated through the growth of highly (100) oriented thin films of cubic ZrO2 (25 mol % Y2O3) on (0001) Al2O3 single crystal substrates, a material system in which film and substrate have dissimilar structures and interatomic spacings. Implications for the growth of epitaxial films using this method are discussed.

Thermotracttve Titanium-Nickel thin Films Formicroelectromechanical Systems and Active Composites

1996 ◽  
Vol 459 ◽  
Author(s):  
D. S. Grummon ◽  
T. J. Pence
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Microelectromechanical Systems ◽  
Thin Film Deposition ◽  
Film Deposition ◽  
Analytical Models ◽  
Internal Variables ◽  
Material System ◽  
Mechanical Stimuli ◽  
Titanium Nickel

ABSTRACTThin films of thermoelastic titanium-nickel are of interest as a material basis for force-producing elements in microelectromechanical systems, and for active phases in mechanically-adaptive composite materials. The successful introduction of this material system into such application areas will depend on development of reliable thin film deposition protocols, together with the refinement of analytical models which successfully predict the response of active microstructures to a variety of dynamic thermal and mechanical stimuli. In the present paper we review some of our recent experimental and theoretical work which bear on these problems. With respect to thin film fabrication techniques we focus on problems of composition control and the manipulation of microstructure, with particular emphasis on opportunities afforded by amorphous precursor phases formed during low temperature processing, and the fine-grained, thermally stable crystalline microstructures obtainable using hot-substrate deposition. The films resulting from either approach retain the important thermomechanical response features of the well-known bulk-alloy system: shape memory and transformational superelasticity. The response can be modeled in terms of a continuum description augmented with internal variables that track fractional partitioning of the material between austenite and variants of the martensite.

Observations on the growth of YBa2Cu3O7-δ thin films on MgO by pulsed-laser ablation

1991 ◽  
Vol 49 ◽  
pp. 1068-1069
Author(s):  
M. Grant Norton ◽  
C. Barry Carter
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Laser Ablation ◽  
Substrate Surface ◽  
Pulsed Laser ◽  
Pulsed Laser Ablation ◽  
Thin Film Deposition ◽  
Film Deposition ◽  
Laser Ablation Process ◽  
Deposition Parameters

Pulsed-laser ablation has been widely used to produce high-quality thin films of YBa2Cu3O7-δ on a range of substrate materials. The nonequilibrium nature of the process allows congruent deposition of oxides with complex stoichiometrics. In the high power density regime produced by the UV excimer lasers the ablated species includes a mixture of neutral atoms, molecules and ions. All these species play an important role in thin-film deposition. However, changes in the deposition parameters have been shown to affect the microstructure of thin YBa2Cu3O7-δ films. The formation of metastable configurations is possible because at the low substrate temperatures used, only shortrange rearrangement on the substrate surface can occur. The parameters associated directly with the laser ablation process, those determining the nature of the process, e g. thermal or nonthermal volatilization, have been classified as ‘primary parameters'. Other parameters may also affect the microstructure of the thin film. In this paper, the effects of these ‘secondary parameters' on the microstructure of YBa2Cu3O7-δ films will be discussed. Examples of 'secondary parameters' include the substrate temperature and the oxygen partial pressure during deposition.

Phenethylammonium bismuth halides: from single crystals to bulky-organic cation promoted thin-film deposition for potential optoelectronic applications

2019 ◽  
Vol 7 (36) ◽  
pp. 20733-20741 ◽  
Author(s):  
Mehri Ghasemi ◽  
Miaoqiang Lyu ◽  
Md Roknuzzaman ◽  
Jung-Ho Yun ◽  
Mengmeng Hao ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Surface Roughness ◽  
Single Crystals ◽  
Organic Cation ◽  
Thin Film Deposition ◽  
Film Deposition ◽  
Optoelectronic Applications ◽  
Excellent Stability

The phenethylammonium cation significantly promotes the formation of fully-covered thin-films of hybrid bismuth organohalides with low surface roughness and excellent stability.

Chemical Bath Deposition of Lead Sulphide (PbS) Thin Film and their Characterization

2013 ◽  
Vol 209 ◽  
pp. 111-115 ◽  
Author(s):  
Sandip V. Bhatt ◽  
M.P. Deshpande ◽  
Bindiya H. Soni ◽  
Nitya Garg ◽  
Sunil H. Chaki
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Raman Spectroscopy ◽  
Thin Film Deposition ◽  
Film Deposition ◽  
Excitation Wavelength ◽  
Face Centered Cubic ◽  
Phonon Modes ◽  
Lead Sulphide ◽  
X Ray

Thin film deposition of PbS is conveniently carried out by chemical reactions of lead acetate with thiourea at room temperature. Energy dispersive analysis of X-ray (EDAX), X-ray diffraction (XRD), selected area electron diffraction patterns (SAED), UV-Vis-NIR spectrophotometer, Scanning Electron Microscopy (SEM), Atomic force microscopy (AFM), Photoluminescence (PL) and Raman spectroscopy techniques are used for characterizing thin films. EDAX spectra shows that no impurity is present and XRD pattern indicates face centered cubic structure of PbS thin films. The average crystallite size obtained using XRD is about 15nm calculated using Scherrer’s formula and that determined from Hall-Williamson plot was found to be 18nm. SAED patterns indicate that the deposited PbS thin films are polycrystalline in nature. Blue shift due to quantum confinement was seen from the UV-Vis-NIR absorption spectra of thin film in comparison with bulk PbS. The Photoluminescence spectra obtained for thin film with different excitation sources shows sharp emission peaks at 395nm and its intensity of photoluminescence increases with increasing the excitation wavelength. Raman spectroscopy of deposited thin film was used to study the optical phonon modes at an excitation wavelength of 488nm using (Ar+) laser beam.

Spray Pyrolysis Thin Film Deposition Technique for Micro-Sensors and Devices

2020 ◽  
pp. 178-202
Author(s):  
Monoj Kumar Singha ◽  
Vineet Rojwal
Keyword(s):  
Thin Film ◽  
Spray Pyrolysis ◽  
Thin Film Deposition ◽  
Deposition Process ◽  
Film Deposition ◽  
Deposition Technique ◽  
Uv Photodetector ◽  
Spray Process ◽  
Spray Pyrolysis Deposition ◽  
Deposition Techniques

Thin film is used for sensing and electronic devices applications. Various techniques are used for thin film deposition. This chapter presents the Spray pyrolysis deposition technique used for the growth of thin films sensing and device material. Spray pyrolysis is an inexpensive method to grow good crystalline thin film compared to other thin film deposition techniques. The chapter gives an overview of the spray process used for thin film deposition. Basic setup for this process is explained. Parameters affecting the deposition process is explained, as are the various spray methods. Finally, some examples of spray pyrolysis in different applications like a gas sensor, UV photodetector, solar cell, photocatalysis, and supercapacitor are discussed.

Stability Studies on Optical and Structure Properties of Zinc Oxide Thin Films Exposed to Different Environment

2013 ◽  
Vol 667 ◽  
pp. 549-552
Author(s):  
A.S.M. Rodzi ◽  
Mohamad Hafiz Mamat ◽  
M.N. Berhan ◽  
Mohamad Rusop Mahmood
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Zinc Oxide ◽  
Absorption Coefficient ◽  
Near Infrared ◽  
Thin Film Deposition ◽  
Film Deposition ◽  
Zno Films ◽  
Zno Thin Film ◽  
Oxide Thin Films

The properties of zinc oxide thin films were prepared by sol-gel spin-coating method have been presented. This study based on optical and electrical properties of ZnO thin film. The effects of annealing temperatures that exposed with two environments properties have been investigated. Environments exposed in room (27°C) and hot (80°C) temperatures which are stored by various days. Solution preparation, thin film deposition and characterization process were involved in this project. The ZnO films were characterized using UV-Vis-NIR spectrophotometer for optical properties. From that equipment, the percentage of transmittance (%) and absorption coefficient spectra were obtained. With two environments showed have different absorption coefficient are reveal and all films have low absorbance in visible and near infrared (IR) region but have high UV absorption properties. From SEM investigations the surface morphology of ZnO thin film shows the particles size become smaller and denser in hot temperatures while in room temperatures have porosity between particles.

Simulation of 3D Films Deposited by Glancing Angle Deposition Using 3D-Films

2000 ◽  
Vol 616 ◽  
Author(s):  
T. Smy ◽  
D. Vick ◽  
M. J. Brett ◽  
S. K. Dew ◽  
A. T. Wu ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Three Dimensional ◽  
Thin Film Deposition ◽  
Glancing Angle Deposition ◽  
Film Deposition ◽  
Porous Thin Films ◽  
Glancing Angle ◽  
Memory Resources ◽  
Angle Deposition

AbstractA new fully three dimensional (3D) ballistic deposition simulator 3D-FILMS has been developed for the modeling of thin film deposition and structure. The simulator may be implemented using the memory resources available to workstations. In order to illustrate the capabilities of 3D-FILMS, we apply it to the growth of engineered porous thin films produced by the technique of GLancing Angle Deposition (GLAD).

Sign in / Sign up

Export Citation Format

Share Document