Numerical Analysis of High-Velocity Oxygen Fuel Thermal-Spray Process for Fe-Based Amorphous Coatings

High-velocity oxygen fuel (HVOF)-sprayed amorphous alloy coatings usually have advantages of a dense structure that improve their resistance to corrosion, wear, and fatigue in the substrate. The flame flow characteristics and particle behaviors during the spray process have a significant influence on the amorphous coating structure and properties. In this study, a computational fluid dynamics model is enforced to analyze the flame flow and Fe-based amorphous alloy particle behavior in an HVOF spray process. The flame flow temperature, velocity characteristics, and the Fe48Cr15Mo14C15B6Y2 Fe-based amorphous alloy particles’ velocities, temperatures, flight trajectories, and mass concentration distribution characteristics are simulated. Moreover, the effects of the oxygen/fuel ratio, particle morphology parameter, particle-injection rate, and angle on the particle behavior are also investigated. Judging from the simulation results, the optimum amorphous alloy particle size varies between 20 and 30 μm, the shape factor is within the range of 0.9–1, the optimum O/F ratio is 3.4, the optimum injection angle is 45°, and the optimum injection rate is 10 m/s. With these conditions, most of the particles settled toward the centerline of the spray gun and are in a semisolid or solid state before affecting the substrate, giving the materials optimal coating structure and performance.

Influence of Cold Spray Parameters on Bonding Mechanisms: A Review

The cold spray process is governed by the impact of high velocity feedstock particles onto a substrate without melting. Hence, the bulk material properties are retained. However, it is challenging to achieve good adhesion strength. The adhesion strength depends on factors such as the cold spray process parameters, substrate conditions, coating/substrate interactions at the interface and feedstock material properties. This review examines fundamental studies concerning the adhesion mechanisms of cold spray technology and considers the effect of cold spray input parameters such as temperature, stand-off-distance, pressure, process gas, spray angle, and traverse speed of the cold spray torch on the bonding mechanism and adhesion strength. Furthermore, the effects of substrate conditions such as temperature, hardness, roughness and material on the adhesion mechanism are highlighted. The effect of feedstock properties, such as feed rate, shape and size are summarized. Understanding the effect of these parameters is necessary to obtain the optimal input parameters that enable the best interfacial properties for a range of coating/substrate material combinations. It is expected that feedstock of spherical morphology and small particle size (<15 μm) provides optimal interfacial properties when deposited onto a mirror-finished substrate surface using high pressure cold spray. Deep insights into each parameter exposes the uncovered potential of cold spray as an additive manufacturing method.

Synthesis of ZnO thin film by chemical spray pyrolysis using its nano powder

The deposition of metal oxides powder faces several problems, including poor adhesion to the bases deposited on them, the presence of many cracks, poor thickness control, and other disadvantages. The current study gives a new and simple idea to deposit thin films using two ZnO powders with nano and microparticle sizes on glass substrates. This was done by transforming the powders to Zinc acetate and then using chemical spray pyrolysis to deposit ZnO thin films. Scanning electron microscope (SEM) images showed that the prepared film from the nanopowder (ZnONano) lost the independence of powder’s nanoparticles and became a homogeneous film with nano projections. But the deposited one from the micro powder (ZnOMicro) had both nanorods and nanoplates. The different shapes and sizes of ZnO particles in ZnOMicro powder were disappeared after the Spray process. The two deposited films were homogeneous, crack-free and there were controllable thicknesses during the deposition. X-ray spectroscopy (EDS) was used to measure weights and atomic percentages of elements for the deposited films. The structures of the deposited films were approximately identical as the X-ray diffraction (XRD) technique showed. The optical properties of these two films were studied and their parameters were measured and calculated.

Monitoring and Optimisation of Ag Nanoparticle Spray-Coating on Textiles

An automatic lab-scaled spray-coating machine was used to deposit Ag nanoparticles (AgNPs) on textile to create antibacterial fabric. The spray process was monitored for the dual purpose of (1) optimizing the process by maximizing silver deposition and minimizing fluid waste, thereby reducing suspension consumption and (2) assessing AgNPs release. Monitoring measurements were carried out at two locations: inside and outside the spray chamber (far field). We calculated the deposition efficiency (E), finding it to be enhanced by increasing the spray pressure from 1 to 1.5 bar, but to be lowered when the number of operating sprays was increased, demonstrating the multiple spray system to be less efficient than a single spray. Far-field AgNPs emission showed a particle concentration increase of less than 10% as compared to the background level. This finding suggests that under our experimental conditions, our spray-coating process is not a critical source of worker exposure.

A Repair Method for Damage in Aluminum Alloy Structures with the Cold Spray Process

Aluminum alloy structures may be damaged due to wear or corrosion while in service. These damages will bring about huge financial costs, as well as a huge amount of energy consumption. There is an urgent need to search for an appropriate repair method in order to solve this problem. In this research, the cold spray process was used to repair the damages by using a mixture of powders with Al and Al2O3. A 7N01-T4 aluminum alloy plate with a factitious pit was regarded as the damaged sample. The microstructure, mechanical properties, and corrosion behavior were studied. The results showed that there were no visible perforative pores or cracks in the repaired areas. The microhardness of the repaired areas was in the range of 57.4–63.2 HV and was lower than that of the 7N01-T4 aluminum alloy. The tensile strength of the repaired samples was markedly improved compared with the unrepaired samples. The alternate immersion test results indicated that the repaired samples had the lowest rate of mass loss compared with 7N01-T4 and the unrepaired samples. After alternate immersion tests for 504 h, the repaired samples were covered with dense corrosion products. The repaired samples had a superior corrosion resistance compared to that of 7N01-T4. Thus, the cold spray process is a method of repairing damage in aluminum alloy structures.