Overview of the French research on the evolution of spent fuel rod after discharge from the reactor

2009 ◽  
Vol 1193 ◽  
Author(s):  
C. Ferry ◽  
C. Cappelaere ◽  
C. Jegou ◽  
J.P. Piron ◽  
M. Firon ◽  
...  
Keyword(s):  
Creep Behaviour ◽  
Creep Model ◽  
Spent Fuel ◽  
Secondary Phases ◽  
Water Contact ◽  
Fuel Rod ◽  
Safety Margins ◽  
The Matrix ◽  
The One

AbstractSince 2006, French research on spent fuel has focused on the main issues related to transport and extended in-pool storage of spent fuel assembly. Studies on creep behaviour of irradiated cladding have resulted in a new creep model which is valid over a wide domain of temperature, internal pressure and time. Under nominal conditions, no evolution of the spent fuel rod is expected during in-pool storage. In case of defective fuel rods in the storage pool, the consequences of fuel alteration on the initial defect of the cladding depend on the matrix alteration rate and nature of the secondary phases formed. Considering the optional scenario of direct disposal, the long-term behaviour of the spent fuel is investigated focusing on helium consequences before water contact on the one hand and on the influence of repository conditions on matrix alteration on the other hand. The aim of the on-going studies is to improve the safety margins initially introduced in the radionuclide source term models.

Constraints by Experimental Data for Modeling of Radionuclide Release from Spent Fuel

1989 ◽  
Vol 176 ◽  
Author(s):  
Bernd Grambow ◽  
L.O. Werme ◽  
R.S. Forsyth ◽  
J. Bruno
Keyword(s):  
Experimental Data ◽  
Product Layer ◽  
Spent Fuel ◽  
Upper Limits ◽  
The Matrix ◽  
The Usa ◽  
Oxidant Production ◽  
Release Data ◽  
Radionuclide Release

ABSTRACTComparison of spent fuel corrosion data from nuclear waste management projects in Canada, Sweden and the USA strongly suggests that the release of 90Sr to the leachant can be used as a measure of the degradation (oxidation/dissolution) of the fuel matrix. A surprisingly quantitative similarity in the 90 Sr release data for fuel of various types (BWR, PWR, Candu), linear power ratings and burnups leached under oxic conditions was observed in the comparison. After 1000 days of leachant contact, static or sequential, the fractional release rates for 90Sr (and for cesium nuclides) were of the order of 10−7/d.The rate of spent fuel degradation (alteration) under oxic conditions can be considered to be controlled either by the growth rates of secondary alteration products, by oxygen diffusion through a product layer, by the rate of formation of radiolytic oxidants or by solubility-controlled dissolution of the matrix. These processes are discussed. Methods for determining upper limits for long-term 90Sr release, and hence fuel degradation, have been derived from the experimental data and consideration of radiolytic oxidant production.

Spent Fuel Corrosion Behavior in Salt Solution in the Presence of Hydrogen Overpressure

2001 ◽  
Author(s):  
Andreas Loida ◽  
Bernd Grambow ◽  
Horst Geckeis
Keyword(s):  
Gas Phase ◽  
Spent Fuel ◽  
Nacl Solution ◽  
Release Rates ◽  
Corrosion Rates ◽  
The Matrix ◽  
Matrix Bound ◽  
Safety Assessments ◽  
Container Material

Abstract The simultaneous corrosion of spent fuel and Fe-based container material is characterized by the formation of large amounts of hydrogen, which control the composition of the gas phase. Various experimental data indicate that the matrix dissolution rate and the release rates of important radionuclides decrease, if the H2 overpressure increases. To quantify to what extent the hydrogen overpressure may counteract radiolysis enhanced matrix dissolution rates, and to take credit from the effect of hydrogen overpressure in long-term safety assessments of the repository, a detailed experimental investigation has been initiated. High burnup spent fuel is being corroded under anoxic conditions in the absence of carbonate in 5m NaCl solution under an external H2 overpressure of 3.3 bar. This pressure is in the same range as observed in a long-term test using spent fuel and Fe-powder. Results obtained after 117 days of testing show that due to constant or decreasing concentrations of Sr and other matrix bound radionuclides, corrosion rates were not measurable indicating a stop of matrix dissolution or very low long-term rates. Grain boundary release of Cs and fission gases was found to continue under hydrogen overpressure. Compared to tests in the absence of hydrogen solution concentrations decreased by about ca. 1.5 orders of magnitude for U (10−8 M), Am, Eu (10−10 M), whereas the decrease of Np (3×10−10 M), Tc (5×10−9 M) and Pu (4×10−9 M) concentrations was found to be less significant.

Long-term settlement of model rock-socketed piers

1989 ◽  
Vol 26 (3) ◽  
pp. 348-358 ◽  
Author(s):  
Robert G. Horvath ◽  
K-J. Chae
Keyword(s):  
Large Scale ◽  
Load Transfer ◽  
Creep Behaviour ◽  
Small Diameter ◽  
Soft Rock ◽  
Load Test ◽  
Creep Model ◽  
Secondary Creep ◽  
Initial Portion

Very little information is available concerning the long-term settlement behaviour of drilled pier foundations socketed into rock. This paper summarizes the results of laboratory investigations of the long-term settlement (creep) behaviour of model socketed pier foundations. The testing program included seven model piers constructed with different materials and different load-support conditions. The primary models were two small-diameter concrete piers constructed in soft shale. For all models tested the results indicated similarly shaped time–displacement curves, having two distinct regions. The initial portion of the curves represents a region of primary creep and the remaining portion represents a zone of secondary creep having a much lower rate of displacement. A comparison of short-term (1 day, which is a normal maximum duration of a full-scale load test) and long-term (200 days) settlements for the model piers showed an 84–245% increase in settlements. In addition, some information concerning load transfer with time in the model piers and available data from loading tests on large-scale socketed piers are included. Key words: socketed pier foundations, long-term settlement, creep model tests, soft rock.

The Effect of Nearfield Constraints on the Corrosion Behavior of High Burnup Spent Fuel

2006 ◽  
Vol 932 ◽  
Author(s):  
Andreas Loida ◽  
Manfred Kelm ◽  
Bernhard Kienzler ◽  
Horst Geckeis ◽  
Andreas Bauer
Keyword(s):  
Host Rock ◽  
Near Field ◽  
Experimental Studies ◽  
Spent Fuel ◽  
Mutual Support ◽  
Significant Extent ◽  
Dissolution Rates ◽  
The Matrix ◽  
Container Material

ABSTRACTThe long-term immobilization for individual radioelements released from the waste form “spent fuel” in solid phases upon groundwater contact depends strongly on the (geo)chemical constraints prevailing in the repository. Related experimental studies comprise effects induced by the presence of Fe based container material, and near field materials other than Fe for a rock salt environment. The effect of the presence of an argillaceous host rock containing organic matter and pyrite on fuel alteration was studied in addition. The results have shown that oxidative radio-lysis products were found to be consumed at a significant extent by the metallic Fe and by the argillaceous host rock. Under these conditions a decrease at a factor of ca.100 for both the matrix dissolution rates and the solution concentrations of U and Pu was found. There is mutual support between the matrix dissolution rates, the solution concentrations and the amounts of oxygen encountered during the experiments under various conditions controlled by the presence of near field materials under study.

scholarly journals A practical creep model for concrete elements under eccentric compression

2019 ◽  
Vol 52 (6) ◽  
Author(s):  
Haidong Huang ◽  
Reyes Garcia ◽  
Shan-Shan Huang ◽  
Maurizio Guadagnini ◽  
Kypros Pilakoutas
Keyword(s):  
Prestressed Concrete ◽  
Creep Behaviour ◽  
Concrete Structures ◽  
Creep Model ◽  
Small Scale ◽  
Compressive Creep ◽  
Eccentric Compression ◽  
Shrinkage And Creep ◽  
Concrete Elements

AbstractMany prestressed concrete bridges are reported to suffer from excessive vertical deflections and cracking during their service life. Creep softens the structure significantly, and therefore an accurate prediction of creep is necessary to determine long-term deflections in elements under eccentric axial compression such as prestressed concrete girders. This study proposes a modification to the creep damage model of Model Code 2010 to account for the effect of load eccentricity. The modified creep model considers damage due to differential drying shrinkage. Initially, the creep behaviour of small scale concrete specimens under eccentric compression load is investigated experimentally. Twelve small-scale concrete prisms were subjected to eccentric axial loading to assess their shrinkage and creep behaviour. The main parameters investigated include the load eccentricity and exposure conditions. Based on the experimental results, an inverse analysis is conducted to determine the main parameters of the modified creep model. Subsequently, a numerical hygro-mechanical simulation is carried out to examine the effect of load eccentricity on the development of shrinkage and creep, and on the interaction between drying, damage and creep. The results indicate that eccentric loading leads to different tensile and compressive creep through the cross section, which contradicts the current design approach that assumes that tensile and compressive creep are identical. The proposed model also predicts accurately the long-term behaviour of tests on reinforced concrete elements available in the literature. This study contributes towards further understanding of the long-term behaviour of concrete structures, and towards the development of advanced creep models for the design/assessment of concrete structures.

Congruent and Incongruent Radionuclide Release During Matrix Dissolution of Partly Oxidized High Burnup Spent Fuel

2000 ◽  
Vol 663 ◽  
Author(s):  
A. Loida ◽  
B. Grambow ◽  
H. Geckeis
Keyword(s):  
Dissolution Rate ◽  
Masking Effect ◽  
Dissolution Behavior ◽  
Spent Fuel ◽  
Ph Values ◽  
Fe Powder ◽  
The Matrix ◽  
Order Of Magnitude ◽  
The Impact

ABSTRACTWith respect to the assessment of the long-term behavior of the waste form spent fuel it is of high importance to study in particular the UO2 matrix dissolution behavior and the associated release/retention of radionuclides in contact with groundwater. During long term fuel storage, fuel oxidation may not be avoided. Main issue of this work is to identify the impact on the corrosion of partly oxidized fuel of environmental conditions such as (1) the nature of solution contacting the matrix, the (2) presence/absence of CO2, (3) fixed pH values within a range between pH 7- pH 11, and (4) the presence/absence of corroding container material (Fe-powder). Dissolution tests with powdered oxidized spent fuel in various granite waters, and NaCl-brine resulted in matrix dissolution rates in the same order of magnitude for all investigated media (ca.5×10−4/d). The presence of CO2 and fixed pH values (pH 5 – 11) was without a distinct effect. The independence of the dissolution rate of the oxidized fuel matrix upon the nature of solution, pCO2, fixed pH values (5-11) can probably be explained by a masking effect of radiolysis. In presence of Fe powder the matrix dissolution rate was found to be slowed down by a factor of ca. 20, associated with strong retention effects of radionuclides.

Radionuclides Release Model for Performance Assessment Studies of Spent Nuclear Fuel in Geological Disposal

2004 ◽  
Vol 824 ◽  
Author(s):  
Christophe Poinssot ◽  
Patrick Lovera ◽  
Cécile Ferry
Keyword(s):  
Nuclear Fuel ◽  
Spent Nuclear Fuel ◽  
Hydrogen Effect ◽  
Spent Fuel ◽  
Geological Disposal ◽  
The Matrix ◽  
Simple Kinetic Model ◽  
Scientific Results ◽  
Release Model

AbstractIn the framework of the research conducted on the long term evolution of spent nuclear fuel in geological disposal conditions, a source term model has been developed to evaluate the instantaneous release of RN (Instant Release Fraction IRF) and the delayed release of the RN which are embedded within the matrix. This model takes into account all the scientific results currently available in the literature except the hydrogen effect. IRF was assessed by considering the evolution with time of the RN inventories located within the fuel microstructure to which no confinement properties can be allocated on the long term (rim, gap, grain boundaries). It allows to propose some reference bounding values for the IRF as a function of time of canister breaching and burnup. The matrix radiolytic dissolution was modeled by a simple kinetic model neglecting the radiolytic species recombination and the influence of aqueous ligands and radiolytic oxidants were supposed to completely react with the fuel surface. Spent fuel performance was therefore demonstrated to deeply depend on the reactive surface area.

Modelling the Activation of H2 on Spent Fuel Surface and Inhibiting Effect of UO2 Dissolution

2013 ◽  
Vol 1518 ◽  
pp. 133-138 ◽  
Author(s):  
L. Duro ◽  
O. Riba ◽  
A. Martínez-Esparza ◽  
J. Bruno
Keyword(s):  
Nuclear Fuel ◽  
Spent Nuclear Fuel ◽  
Fuel Pellet ◽  
Dissolution Behavior ◽  
Dissolution Mechanism ◽  
Water Radiolysis ◽  
Spent Fuel ◽  
Secondary Phases ◽  
The Matrix ◽  
Fuel Storage

ABSTRACTThe dissolution of spent nuclear fuel is defined in two different time steps, i) the Instant Release Fraction (IRF) occurring shortly after water contacts the solid spent fuel and responsible of the fast release of those radionuclides that have been accumulated in the zones of the spent fuel pellet with low confinement, such as gap and grain boundaries and ii) the long term release of radionuclides confined in the spent fuel matrix, much slower and dependent on the conditions of the water that contacts the spent fuel.Several models have been developed to date to explain the dissolution behavior of spent nuclear fuel under disposal conditions. The Matrix Alteration Model (MAM) is one of the most evolved radiolytic models describing the dissolution mechanism in which an Alteration/Dissolution source term model is based on the oxidative dissolution of spent fuel. Under deep repository conditions and at the expected of water contacting time (after 1000 years of spent fuel storage), α radiation will be the main contributor to water radiolysis. In the current study, simulations evaluating the effect of surface area on the alteration/dissolution of spent fuel matrix are performed considering different particle sizes of spent fuel and simulations integrating the actinides dissolution have been performed considering the precipitation of secondary phases.

Mobilization/Retention of Radionuclides during Corrosion of High Burnup Spent Fuel and Backfill Materials in Salt Brines

2002 ◽  
Vol 757 ◽  
Author(s):  
Andreas Loida ◽  
Bernhard Kienzler ◽  
Horst Geckeis
Keyword(s):  
Near Field ◽  
Waste Form ◽  
Spent Fuel ◽  
The Matrix ◽  
Backfill Materials ◽  
Salt Brine ◽  
Solid Phases ◽  
Long Term Behavior ◽  
The Impact

ABSTRACTWith respect to the assessment of the long-term behavior of the waste form spent fuel it is of high importance to study the fuel alteration in contact with groundwater and near field materials. The aim of this work is to evaluate the impact of candidate backfill materials hydroxylapatite and magnetite on the overall corrosion behavior of this waste form in salt brine; both materials are used in corrosion tests together with spent fuel. The instant releases and the matrix dissolution rates appear to be similar in presence and in absence of any backfill material under study. However, Am,Np,Pu,U and Sr are retained at different ratios on the hydroxylapatite, on the magnetite and on the fuel sample, indicating possibly the formation of different radionuclide containing new solid phases.

Measurement of Soluble Nuclide Dissolution Rates from Spent Fuel

1989 ◽  
Vol 176 ◽  
Author(s):  
C. N. Wilson ◽  
W. J. Gray
Keyword(s):  
Yucca Mountain ◽  
Water Soluble ◽  
Spent Fuel ◽  
Release Rates ◽  
Dissolution Rates ◽  
Advantages And Disadvantages ◽  
Water Composition ◽  
The Matrix ◽  
Flow Through

ABSTRACTGaining a better understanding of the potential release behavior of water-soluble radionuclides is the focus of new laboratory spent fuel dissolution studies being planned in support of the Yucca Mountain Project. Previous studies have suggested that maximum release rates for actinide nuclides, which account for most of the long-term radioactivity in spent fuel, should be solubility-limited and should not depend on the characteristics or durability of the spent fuel waste form. Maximum actinide concentrations should be sufficiently low to meet the NRC annual release limits. Potential release rates for soluble nuclides such as 99Tc, 135Cs, 14C and 129I, which account for about 1-2% of the activity in spent fuel at 1000 years, are less certain and may depend on processes such as oxidation of the fuel in the repository air environment.Dissolution rates for several soluble nuclides have been measured from spent fuel specimens using static and semi-static methods. However, such tests do not provide a direct measurement of fuel matrix dissolution rates that may ultimately control soluble-nuclide release rates. Flow-through tests are being developed as a potential supplemental method for determining the matrix component of soluble-nuclide dissolution. Advantages and disadvantages of both semi-static and flow-through methods are discussed. Tests with fuel specimens representing a range of potential fuel states that may occur in the repository, including oxidized fuel, are proposed. Preliminary results from flow-through tests with unirradiated UO2 suggesting that matrix dissolution rates are very sensitive to water composition are also presented.

Sign in / Sign up

Export Citation Format

Share Document