Synthesis of Dislocation Free Siy(SnxC1−x)1−y Alloys by Molecular Beam Deposition and Solid Phase Epitaxy

1993 ◽  
Vol 298 ◽  
Author(s):  
Gang He ◽  
Mark D. Savellano ◽  
Harry A. Atwater
Keyword(s):  
Molecular Beam ◽  
Solid Phase ◽  
Solid Phase Epitaxy ◽  
X Ray Diffraction ◽  
Time Resolved ◽  
Pure Silicon ◽  
Ion Channeling ◽  
Transmission Electron ◽  
Molecular Beam Deposition ◽  
Beam Deposition

AbstractSynthesis of strain-compensated single-crystal Siy(SnxC1-x)1-y alloy films on silicon (100) substrates has been achieved with compositions of tin and carbon greatly exceeding their normal equilibrium solubility in silicon. Amorphous SiSnC alloys were deposited by molecular beam deposition from solid sources followed by thermal annealing. In situ monitoring of crystallization was done using time-resolved reflectivity. Good solid phase epitaxy was observed for Si0.98Sn0.01C0.01, at a rate about 20 times slower than that of pure silicon. Compositional and structural analysis was done using Rutherford backscattering, electron microprobe, ion channeling, x-ray diffraction, and transmission electron microscopy.

Interfacial Superstructures Studied by Grazing Incidence X-Ray Diffraction

1989 ◽  
Vol 159 ◽  
Author(s):  
Koichi Akimoto ◽  
Jun'Ichiro Mizuki ◽  
Ichiro Hirosawa ◽  
Junji Matsui
Keyword(s):  
Synchrotron Radiation ◽  
Direct Observation ◽  
Molecular Beam ◽  
Solid Phase ◽  
Grazing Incidence ◽  
Deposition Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Molecular Beam Deposition ◽  
Beam Deposition

ABSTRACTSurface superstructures (reconstructed structures) have been observed by many authors. However, it is not easy to confirm that a superstructure does exist at an interface between two solid layers. The present paper reports a direct observation, by a grazing incidence x-ray diffraction technique with use of synchrotron radiation, of superstructures at the interface. Firstly, the boron-induced R30° reconstruction at the Si interface has been investigated. At the a Si/Si(111) interface, boron atoms at 1/3 ML are substituted for silicon atoms, thus forming a R30° lattice. Even at the interface between a solid phase epitaxial Si(111) layer and a Si(111) substrate, the boron-induced R30° reconstruction has been also observed. Secondly, SiO2/Si(100)-2×l interfacial superstructures have been investigated. Interfacial superstructures have been only observed in the samples of which SiO2 layers have been deposited with a molecular beam deposition method. Finally, the interfaces of MOCVD-grown AIN/GaAs(100) have been shown to have 1×4 and 1×6 superstructures.

Solute Segregation and Dynamics of Solid-Phase Crystallization In in and Sb-Implanted Silicon

1981 ◽  
Vol 4 ◽  
Author(s):  
J. Narayan ◽  
G. L. Olson ◽  
O. W. Holland
Keyword(s):  
Laser Power ◽  
Solid Phase ◽  
Solute Segregation ◽  
Dislocation Loops ◽  
Solid Phase Crystallization ◽  
Time Resolved ◽  
Plan View ◽  
Ion Channeling ◽  
Retrograde Solubility ◽  
Transmission Electron

ABSTRACTTime-resolved-reflectivity measurements have been combined with transmission electron microscopy (cross-section and plan-view), Rutherford backscattering and ion channeling techniques to study the details of laser induced solid phase epitaxial growth in In+ and Sb+ implanted silicon in the temperature range from 725 to 1500 °K. The details of microstructures including the formation of polycrystals, precipitates, and dislocations have been correlated with the dynamics of crystallization. There were limits to the dopant concentrations which could be incorporated into substitutional lattice sites; these concentrations exceeded retrograde solubility limits by factors up to 70 in the case of the Si-In system. The coarsening of dislocation loops and the formation of a/2<110>, 90° dislocations in the underlying dislocation-loop bands are described as a function of laser power.

GROWTH AND CHARACTERIZATION OF EPITAXIAL Si/CoSi2 AND Si/CoSi2/Si HETEROSTRUCTURES

1985 ◽  
Vol 56 ◽  
Author(s):  
B.D. HUNT ◽  
N. LEWIS ◽  
E.L. HALL ◽  
L.G. JTURNER ◽  
L.J. SCHOWALTER ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Growth Temperature ◽  
Molecular Beam ◽  
Solid Phase ◽  
Solid Phase Epitaxy ◽  
Cross Sectional ◽  
Reactive Deposition ◽  
Ion Channeling ◽  
Formation Method

AbstractThin (<200Å), epitaxial CoSi2 films have been grown on (111) Siwafers in a UHV system using a variety of growth techniques including solid phase epitaxy (SPE), reactive deposition epitaxy (RDE), and molecular beam epitaxy (MBE). SEN and TEN studies reveal significant variations in the epitaxial silicide surface morphology as a function of the sillciqd formation method. Pinhole densities are generally greater than 107 cm-2, although some reduction can be achieved by utilizing proper growth techniques. Si epilayers were deposited over the CoSi2 films inthe temperature range from 550ºC to 800ºC, and the reesuulttinng structures have been characterized using SEM, cross—sectional TEN, and ion channeling measurements. These measurements show that the Si epitaxial quality increases with growth temperature, although the average Si surface roughness and the CoSi2 pinhole density also increase as the growth temperature is raised.

Electrical Activation of Heavily Doped Arsenic Implanted Silicon

1988 ◽  
Vol 128 ◽  
Author(s):  
J. Said ◽  
H. Jaouen ◽  
G. Ghibaudo ◽  
I. Stoemenos ◽  
P. Zaumseil
Keyword(s):  
Solid Phase ◽  
Electrical Activation ◽  
Activation Process ◽  
Solid Phase Epitaxy ◽  
X Ray Diffraction ◽  
Electrical Transmission ◽  
X Ray ◽  
Defect Migration ◽  
Transmission Electron ◽  
Heavily Doped

ABSTRACTThe combination of electrical, Transmission Electron Microscopy and Triple Crystal X-ray Diffraction measurements allow us to separate the existence of a local impurity activation process from the amorphous- crystal transformation. The local process occurs in the highly damaged surface layer induced by the arsenic implantation and is efficient well below the Solid Phase Epitaxy transition temperature. It is suggested that point defect migration should play an important role in the electrical impurity activation at low annealing temperatures.

Crystallization Kinetics of Fe-DOPED A1203

1994 ◽  
Vol 357 ◽  
Author(s):  
Todd W. Simpson ◽  
Ian V. Mitchell ◽  
Ning Yu ◽  
Michael Nastasi ◽  
Paul C. Mcintyre
Keyword(s):  
Crystallization Kinetics ◽  
Annealing Temperature ◽  
Rutherford Backscattering Spectrometry ◽  
Solid Phase ◽  
Solid Phase Epitaxy ◽  
Time Resolved ◽  
Α Phase ◽  
Kinetics Of ◽  
Beam Deposition

AbstractTime resolved optical reflectivity (TRR) and Rutherford backscattering spectrometry (RBS) and ion channelling methods have been applied to determine the crystallization kinetics of Fe-doped A1203 in the temperature range of 900-1050°C. Amorphous A1203 films, approximately 250 nm thick and with Fe cation concentrations of 0, 1.85, 2.2 and 4.5%, were formed by e-beam deposition on single crystal, [0001] oriented, A1203 substrates. Annealing was performed under an oxygen ambient in a conventional tube furnace, and the optical changes which accompany crystallization were monitored, in situ, by TRR with a 633nm wavelength laser.Crystallization is observed to proceed via solid phase epitaxy. An intermediate, epitaxial phase of -γ-Al203 is formed before the samples reach the ultimate annealing temperature. The 5% Fe-doped film transforms from γ to α-A1203 at a rate approximately 10 times that of the pure A1203 film and the 1.85% and 2.2% Fe-doped films transform at rates between these two extremes. The Fe-dopants occupy substitional lattice sites in the epilayer. Each of the four sets of specimens displays an activation energy in the range 5.0±0.2eV for the γ,α phase transition.

Laser Solid-Phase-Epitaxy of Amorphous Si1−xGex layer on Si

1992 ◽  
Vol 279 ◽  
Author(s):  
Yasunori Sogoh ◽  
Kouicbi Murakami ◽  
Kohzoh Nasuda
Keyword(s):  
Solid Phase ◽  
Central Area ◽  
Solid Phase Epitaxy ◽  
Small Areas ◽  
Molecular Beam Deposition ◽  
Amorphous Si ◽  
Short Time ◽  
Power Densities ◽  
Beam Deposition ◽  
Strained Sige

ABSTRACTLaser Solid-phase-epitaxy (SPE) of amorphous Si1−xGex layer on Si formed by the molecular beam deposition (MBD) method was successfully performed by cw-Kr laser irradiation. Laser SPE of small areas was achieved by Laser irradiations of short time durations and high power densities The strain in the Laser-SPE layers was evaluated by micro-Raman scattering. It is demonstrated that strained SiGe layers on Si can be grown in the central area of 10μm size within the area crystallized by Laser- SPE at a substrate temperature of 400°C after preannealing at 350°C for 15 to 30 minutes.

Heteroepitaxial Bi2Sr2CaCu2Ox Superconducting thin films Deposited on LaA1O3 by Solid Phase Epitaxy and OMCVD

1992 ◽  
Vol 275 ◽  
Author(s):  
J. Chen ◽  
H. A. Lu ◽  
F. DiMeo ◽  
B. W. Wessels ◽  
D. L. Schulz ◽  
...  
Keyword(s):  
Thin Films ◽  
Solid Phase ◽  
Chemical Vapor ◽  
Superconducting Thin Films ◽  
Epitaxial Thin Films ◽  
Solid Phase Epitaxy ◽  
X Ray Diffraction ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Film Substrate

ABSTRACT-Heteroepitaxial superconducting Bi,Sr2CaCu2Ox (BSCCO 2212) thin films have been formed by solid phase epitaxy from amorphous films deposited on (100) LaA1O3 single crystal substrates by organometallic chemical vapor deposition. The epitaxial structure of the film is confirmed by x-ray diffraction including θ/2θ and Φ (in plane rotation) scans. Cross-sectional high resolution transmission electron microscopy indicates that the film-substrate interface is nearly atomically abrupt. Improvements in superconducting properties of the epitaxial thin films are noted in comparison to highly textured films deposited on MgO.

Sign in / Sign up

Export Citation Format

Share Document