scholarly journals The Effect of Cooling Rate During Rapid Solidification on the Structure and Texture of NiTi

1986 ◽  
Vol 74 ◽  
Author(s):  
A. J. Pedraza ◽  
M. J. Godbole ◽  
E. A. Kenik ◽  
D. F. Pedraza ◽  
D. H. Lowndes
Keyword(s):  
Cooling Rate ◽  
Rapid Solidification ◽  
Heat Extraction ◽  
X Ray Diffraction ◽  
Rapid Solidification Technique ◽  
Melted Layer ◽  
Monoclinic Distortion ◽  
Small Distortion ◽  
B2 Phase ◽  
Rapidly Solidified

AbstractA study has been conducted on the effects of increasing cooling rate during rapid solidification of NiTi upon the phases that are produced. The hammer and anvil rapid solidification technique and laser melting with a nanosecond excimer laser were used, which allow the cooling rate to be varied by three to four orders of magnitude. Although 1/3 {110} superlattice reflections are seen in the selected area diffraction (SAD) patterns of the splat quenched (SQ) specimens, x-ray diffraction analyses show the presence of only B2 phase and martensite. On the other hand, laser treatment (LT) of the specimens produces a layer that has a L10 structure with a slight monoclinic distortion. This phase can be envisaged as a small distortion of a B2 unit cell with a volume per atom ~3.3% lower than the equilibrium B2 phase. Also martensite is present in the layer. SQ alloys exhibit a marked {200} texture due to columnar growth opposite to the direction of heat extraction, while LT produces epitaxial regrowth of the melted layer. No substantial disordering is obtained in NiTi rapidly solidified alloys.

scholarly journals The Development of Rapidly Solidified Magnesium – Copper Ribbons

2016 ◽  
Vol 61 (2) ◽  
pp. 1083-1088
Author(s):  
M. Pastuszak ◽  
G. Cieślak ◽  
A. Dobkowska ◽  
J. Mizera ◽  
K.J. Kurzydłowski
Keyword(s):  
Corrosion Resistance ◽  
Cooling Rate ◽  
Melt Spinning ◽  
Diffraction Method ◽  
Electrode System ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Copper Addition ◽  
Rapidly Solidified ◽  
Thermal Stability Of

Abstract The aim of the present work was to plan and carry out an experiment consisting of amorphization of industrial magnesium alloy WE 43 (Mg - 4 Y - 3 RE - 0.5 Zr) modified by the copper addition. Investigated alloy modified with 20% of copper was rapidly quenched with the use of melt spinning technique. The effects of cooling rate on the structure and properties of the obtained material were extensively analyzed. The structure and phase analysis of samples were examined using X-ray diffraction method (XRD) while the thermal stability of the samples was determined by differential scanning calorimetry (DSC). Microstructure observations were also conducted. The microhardness tests (HV0.02) and corrosion resistance tests were carried out to investigate the properties of the material. Corrosion resistance measurements were held using a typical three-electrode system. As the result of the research, the effect of cooling rate on microstructure and properties of investigated alloy was determined.

Microstructure and Properties of Rapidly Solidified Al-Zn-Mg-Cu Alloy

2020 ◽  
Vol 993 ◽  
pp. 203-207
Author(s):  
Wei Min Ren ◽  
Zi Yong Chen ◽  
Zhi Lei Xiang ◽  
Li Hua Chai
Keyword(s):  
Aluminum Alloy ◽  
Aluminum Alloys ◽  
Cooling Rate ◽  
Rapid Solidification ◽  
Second Phase ◽  
Alloy Strip ◽  
Roller Speed ◽  
Microstructure And Properties ◽  
Cu Alloy ◽  
Rapidly Solidified

Refining grain plays an important role in improving the mechanical properties of aluminum alloys. However, the conventional casting method with a slow cooling rate can be easy to cause coarseness of the microstructure and serious segregation. In this paper, the rapid solidification of Al-Zn-Mg-Cu alloy was prepared by the single-roller belt method. The alloy strip was studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and hardness test to study the microstructure and properties of the rapidly solidified aluminum alloy. The results show that the roller speed was an important parameters affecting the formability of the alloy. When the roller speed was 15 m/s, the aluminum alloy produced a thin bandwidth of 5 mm and a thickness of 150 um. As the rotation speed of the roller increased, the cooling rate of the melt increased, and the microstructure of the rapidly solidified Al-Zn-Mg-Cu aluminum alloy strip improved in grains refinement. Compared with the conventionally cast Al-Zn-Mg-Cu aluminum alloys, the Al-Zn-Mg-Cu aluminum alloys prepared by rapid solidification showed much finer crystal grains, and enhanced solid solubility of alloying elements with less precipitation of second phase and high hardness.

Microstructure & Phase Transformation in Rapidly Solidified V-Ga Alloys

1986 ◽  
Vol 80 ◽  
Author(s):  
M. W. Park ◽  
S. H. Whang ◽  
S. Karmarkar ◽  
D. Divecha
Keyword(s):  
Heat Treatment ◽  
Phase Transformation ◽  
Grain Refinement ◽  
Rapid Solidification ◽  
Rapid Quenching ◽  
X Ray Diffraction ◽  
X Ray ◽  
Rapidly Solidified ◽  
A15 Phase

AbstractThe A15 Phase forming V-Ga alloys were processed into ribbons and foils by rapid solidification techniques. Microstructures and phase transformation in these alloys by rapid solidification and succeeding heat treatment were investigated by x-ray diffraction and TEM. It is shown that equilibrium A15 phases can readily be suppressed by rapid quenching in these alloys. A significant grain refinement resulting from the rapid solidification also was observed. Microhardnesses of these alloys as a function of Ga concentration were determined.

Rapidly Solidified Al-6Si-3Cu Alloy

2008 ◽  
Vol 570 ◽  
pp. 103-108 ◽  
Author(s):  
C. Triveño Rios ◽  
Claudemiro Bolfarini ◽  
Walter José Botta Filho ◽  
Claudio Shyinti Kiminami
Keyword(s):  
Rapid Solidification ◽  
X Ray Diffraction ◽  
Type Alloy ◽  
X Ray ◽  
Optical Scanning ◽  
Transmission Electron ◽  
Al2cu Phase ◽  
Solidification Processes ◽  
Dendritic Arm Spacing ◽  
Rapidly Solidified

Rapid solidification processes, RSP, are powerful tools to induce microstructural modifications, which may improve mechanical properties of alloys. In this paper the influence of rapid solidification on the formation of the undesirable brittle intermetallic compounds promoted by Si and Fe in Al-6Si-3Cu (A319-type) alloy have been investigated. The alloy have been casted using both conventional method and water-cooled wedge-copper mould. The microstructures have been evaluated by using a combination of X-ray diffraction, optical, scanning and transmission electron microscopy, and by Vickers microhardness. By increasing the cooling rate the length of the intermetallic β-Al5FeSi phase decreased, accompanying the same tendency of the secondary dendritic arm spacing. These results are accompanied by an increasing in hardness. Moreover, the formation and growth of the Al2Cu phase have been suppressed. These microstructural and hardness changes with the rapid solidification might be attributed to the increased solid solution content of the elements in the Al matrix.

Rapid Solidification Microstructures and Precipitation in AL-Mn Alloys

1983 ◽  
Vol 28 ◽  
Author(s):  
R. J. Schaefer ◽  
D. Shechtman ◽  
F. S. Biancaniello
Keyword(s):  
Rapid Solidification ◽  
Growth Kinetics ◽  
Melt Spinning ◽  
X Ray Diffraction ◽  
X Ray ◽  
Rapidly Solidified ◽  
Solidification Microstructures ◽  
Al Matrix

ABSTRACTRapidly solidified Al containing up to to 15 wt.% Mn was prepared by melt spinning. The alloys were examined by TEM and X-ray diffraction in the as-spun condition and after annealing at 450°C. Four precipitate phases were detected, and their growth kinetics were correlated to subgrain structures in the Al matrix.

Development of Ni-Mn-Ga Based Ferromagnetic Shape Memory Alloy by Rapid Solidification Technique

2008 ◽  
Vol 52 ◽  
pp. 17-27
Author(s):  
Amitava Mitra ◽  
A.K. Panda
Keyword(s):  
Shape Memory Alloy ◽  
Shape Memory ◽  
Rapid Solidification ◽  
Melt Spinning ◽  
X Ray Diffraction ◽  
Ferromagnetic Shape Memory Alloy ◽  
Electron Microscopic ◽  
Transmission Electron ◽  
Rapid Solidification Technique ◽  
Ferromagnetic Shape Memory

Rapid solidification route by melt spinning has been adopted for preparation of a Ni52.5Mn24.5Ga23 (at %) ferromagnetic shape memory alloy in the form of ribbons. In the as-spun state, the ribbon revealed a predominant austenitic L21 structure in combination with martensitic feature as observed from x-ray diffraction studies. Transmission electron microscopic (TEM) evaluation showed these features in the form of martensitic plates. At low temperature, martensite to austenite transformation was exhibited by an increase in magnetization during heating cycle. The reverse effect was observed during cooling cycle. Annealing temperature and magnetising field was also found to effect this transformation.

scholarly journals Nucleation behaviour and microstructure of single Al-Si12 powder particles rapidly solidified in a fast scanning calorimeter

2021 ◽  
Author(s):  
Bin Yang ◽  
Qin Peng ◽  
Benjamin Milkereit ◽  
Armin Springer ◽  
Dongmei Liu ◽  
...  
Keyword(s):  
Cooling Rate ◽  
Rapid Solidification ◽  
Heterogeneous Nucleation ◽  
Cooling Rates ◽  
Solidification Behaviour ◽  
Nucleation Undercooling ◽  
In Situ Investigation ◽  
Solidification Processes ◽  
Powder Particles ◽  
Rapidly Solidified

AbstractThe understanding of rapid solidification behaviour, e.g. the undercooling versus growth velocity relationship, is crucial for tailoring microstructures and properties in metal alloys. In most rapid solidification processes, such as additive manufacturing (AM), in situ investigation of rapid solidification behaviour is missing because of the lack of accurate measurement of the cooling rate and nucleation undercooling. In the present study, rapid solidification of single micro-sized Al-Si12 (mass%) particles of various diameters has been investigated via differential fast scanning calorimetry employing controllable cooling rates from 100 to 90,000 K s−1 relevant for AM. Based on nucleation undercooling and on microstructure analysis of rapidly solidified single powder particles under controlled cooling rates, two different heterogeneous nucleation mechanisms of the primary α-Al phase are proposed. Surface heterogeneous nucleation dominates for particles with diameter smaller than 23 μm. For particles with diameter larger than 23 μm, the nucleation of the primary α-Al phase changes from surface to bulk heterogeneous nucleation with increasing cooling rate. The results indicate that at large undercoolings (> 95 K) and high cooling rates (> 10,000 K s−1), rapid solidification of single particle can yield a microstructure similar to that formed in AM. The present work not only proposes new insight into rapid solidification processes, but also provides a theoretical foundation for further understanding of microstructures and properties in additively manufactured materials.

Metastable ordered austenite in rapidly solidified Fe-Al-C alloys

1989 ◽  
Vol 47 ◽  
pp. 516-517
Author(s):  
J. A. Sarreal
Keyword(s):  
Rapid Solidification ◽  
Melt Spinning ◽  
X Ray Diffraction ◽  
Austenitic Phase ◽  
X Ray ◽  
Transmission Electron ◽  
Melt Spun ◽  
Melt Spun Ribbons ◽  
Equilibrium Phases ◽  
Rapidly Solidified

Conventionally cast Fe-Al-C alloys are extremely brittle containing combinations of ferrite, carbide and other phases. Rapid solidification has the potential of altering the microstructure to subsequently change the resulting mechanical properties. An apparent conflict exist concerning the effect of rapid solidification on the resulting microstructure of these alloys. Inoue and co-workers, using transmission electron microscopy (TEM) and electron diffraction analyses, reported the presence of several non-equilibrium phases including austenite (fcc - γ) and ordered austenite (Ll2-γ') structures on alloys containing 1.7 to 2.1 C and 6 to 12 Al in weight % (w/o) on melt spun ribbons 30 μm in thickness. Han and Choo, using x-ray diffraction analysis on 30-48 μm thick melt spun ribbons concluded that this ordered fee phase is rather an austenitic phase in which phase decomposition accompanied by sideband phenomenon had occured.Single roller melt spinning technique was used to make ribbons 35-70 μm thick and 0.5-5 mm wide. X-ray diffration analysis showed single phase austenite for samples 2-6 w/o AI and 2 w/o C. Samples with 8-10 w/o AI and 2 w/o C also showed several superlattice lines in addition to the fundamental fcc peaks.

Cooling Rate and Microstructural Investigation of Rapidly Solidified Spherical Mono-Sized Copper Particles

2020 ◽  
Vol 976 ◽  
pp. 42-49
Author(s):  
Ying Yan Hu ◽  
Jun Feng Wang ◽  
Can Li ◽  
Yi Ying Gao ◽  
Jian Qiang Li
Keyword(s):  
Grain Boundary ◽  
Cooling Rate ◽  
Rapid Solidification ◽  
Particle Diameter ◽  
Spherical Shape ◽  
Microstructural Investigation ◽  
Argon Gas ◽  
Copper Particles ◽  
Rapidly Solidified ◽  
The Relationship

Spherical copper particles with diameter ranging from 120.6 to 437.0 μm were prepared by the pulsated orifice ejection method (termed “POEM”). These spherical copper particles exhibit a good spherical shape and a narrow size distribution, suggesting that the liquid copper can completely break the balance between the surface tension and the liquid static pressure in the crucible micropores and accurately control the volume of the droplets. Furthermore, the relationship between cooling rate and microstructures of spherical copper particles was carried out with a specific focus on different cooling atmosphere and particle diameter during the rapid solidification. The cooling rate of spherical copper particles is evaluated by a Newton’s cooling model. It is revealed that the cooling rate was depended on cooling medium and particle diameter. The cooling rate decreases and the grain size increases with the increase of particle diameter during the rapid solidification, while the grain boundary of same particle diameter with larger cooling rate in argon gas is smaller, while the grain boundary of particles with smaller cooling rate in helium gas is larger. When the particle diameter is larger than 100 μm, the cooling rate of the cooper droplet in argon gas achieves 1.0×104 K/s. Meanwhile, the cooling rate decreases rapidly when the particle diameter increased between 70.6 and 149.6 μm. It is an effective route for fabrication of high-quality spherical copper particles.

Microstructures of Ni3 Al Rapidly Solidified by Hammer-Anvil Technique

1990 ◽  
Vol 186 ◽  
Author(s):  
Yoshinao Mishima ◽  
Shirou Sasaki ◽  
Tomoo Suzuki
Keyword(s):  
Cooling Rate ◽  
Rapid Solidification ◽  
Phase Field ◽  
Aluminum Concentration ◽  
The Difference ◽  
Equilibrium Phases ◽  
Rapidly Solidified ◽  
Non Equilibrium

AbstractThe Hammer-Anvil technique is employed for the rapid solidification of Ni3Al in the present work. The effect of off-stoichiometry on the change in the microstructure in the quenched alloy is examined for compositions within the L12 phase field at equilibrium. It is shown that non-equilibrium phases of various morphologies appear with fine grains of Ll2 phase, which have never been reported for the compound rapidly solidified by the roll techniques. With increasing aluminum concentration and with increase in cooling rate, the latter being judged by the difference in the thickness of the quenched foil, the fraction of the non-equilibrium phases appearing is found to increase giving more complex microstructure.

Sign in / Sign up

Export Citation Format

Share Document