Towards Novel Light-Activated Shape Memory Polymer: Thermomechanical Properties of Photo-responsive Polymers

2005 ◽  
Vol 872 ◽  
Author(s):  
Emily A. Snyder ◽  
Tat H. Tong
Keyword(s):  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Room Temperature ◽  
Shape Memory Polymer ◽  
Crosslinking Density ◽  
Material System ◽  
Effect Change ◽  
Responsive Polymers ◽  
Original Shape

AbstractThe basic principle for the operation of a thermally stimulated shape memory polymer (SMP) is a drastic change in elastic modulus above the glass transition temperature (Tg). This change from glassy modulus to rubbery modulus allows the material to be deformed above the Tg and retain the deformed shape when cooled below the Tg. The material will recover its original shape when heated above the Tg again. However, thermal activation is not the only possibility for a polymer to exhibit this shape memory effect or change of modulus. This paper discusses results of an alternative approach to SMP activation.It is well known that the Tg of a thermosetting polymer is proportional to its crosslinking density. It is possible for the crosslinking density of a room temperature elastomer to be modified through photo-crosslinking special photo-reactive monomer groups incorporated into the material system in order to increase its Tg. Correspondingly, the modulus will be increased from the rubbery state to the glassy state. As a result, the material is transformed from an elastomer to a rigid glassy photoset, depending on the crosslinking density achieved during exposure to the proper wavelength of light. This crosslinking process is reversible by irradiation with a different wavelength, thus making it possible to produce light-activated SMP materials that could be deformed at room temperature, held in deformed shape by photo-irradiation using one wavelength, and recovered to the original shape by irradiation with a different wavelength.In this work, monomers which contain photo-crosslinkable groups in addition to the primary polymerizable groups were synthesized. These monomers were formulated and cured with other monomers to form photo-responsive polymers. The mechanical properties of these materials, the kinetics, and the reversibility of the photo-activated shape memory effect were studied to demonstrate the effectiveness of using photo-irradiation to effect change in modulus (and thus shape memory effect).

Fe-Mn-Si Based Shape Memory Alloys

1991 ◽  
Vol 246 ◽  
Author(s):  
H. Otsuka
Keyword(s):  
Shape Memory Alloys ◽  
Shape Memory ◽  
Shape Memory Effect ◽  
Thermomechanical Treatment ◽  
Memory Effect ◽  
Room Temperature ◽  
Steel Pipe ◽  
Original Shape ◽  
Ε Martensite ◽  
Pipe Joints

AbstractFe-Mn-Si based alloys are non-thermoelastic shape memory alloys which utilize the stress-induced transformation from γ austenite to ε martensite. After these shape memory alloys are deformed at room temperature, they recover their original shape when heated to 473K or higher. Fe-Mn-Si based alloys contain 15% to 33% Mn, 5% to 6% Si, 0% to 13% Cr, and 0% to 10% Ni in weight. Mn and Si are indispensable for the development of shape memory effect (SME). The amounts of these elements require to be adjusted so that the Neel temperature (TN) lies lower than Ms temperature and the Ms lies just below room temperature. Though the volume of stress-induced martensite is only 20 to 30%, a thermomechanical treatment called “training” has made it possible for the alloy to recover from a tensi le deformation exceeding 3%. Today, the use of the shape memory al loys for steel pipe joints is being studied. They have already been put into practical use for an auxiliary bicycle part to clamp the frame.

High performance shape memory effect in nitinol wire for actuators with increased operating temperature range

2014 ◽  
Vol 07 (05) ◽  
pp. 1450063 ◽  
Author(s):  
Riccardo Casati ◽  
Carlo Alberto Biffi ◽  
Maurizio Vedani ◽  
Ausonio Tuissi
Keyword(s):  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
High Performance ◽  
Room Temperature ◽  
Operating Temperature ◽  
Niti Wire ◽  
Shape Memory Actuators ◽  
Nitinol Wire ◽  
Operating Temperature Range

In this research, the high performance shape memory effect (HP-SME) is experimented on a shape memory NiTi wire, with austenite finish temperature higher than room temperature. The HP-SME consists in the thermal cycling of stress induced martensite and it allows achieving mechanical work higher than that produced by conventional shape memory actuators based on the heating/cooling of detwinned martensite. The Nitinol wire was able to recover about 5.5% of deformation under a stress of 600 MPa and to withstand about 5000 cycles before failure. HP-SME path increased the operating temperature of the shape memory actuator wire. Functioning temperatures higher than 100°C was reached.

Cold Bending a Ni-Ti Shape Memory Alloy Wire

2015 ◽  
Vol 661 ◽  
pp. 98-104 ◽  
Author(s):  
Kuang-Jau Fann ◽  
Pao Min Huang
Keyword(s):  
Shape Memory Alloy ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Room Temperature ◽  
Aging Treatment ◽  
Treatment Temperature ◽  
Bending Test ◽  
Solution Treatment Temperature

Because of being in possession of shape memory effect and superelasticity, Ni-Ti shape memory alloys have earned more intense gaze on the next generation applications. Conventionally, Ni-Ti shape memory alloys are manufactured by hot forming and constraint aging, which need a capital-intensive investment. To have a cost benefit getting rid of plenty of die sets, this study is aimed to form Ni-Ti shape memory alloys at room temperature and to age them at elevated temperature without any die sets. In this study, starting with solution treatments at various temperatures, which served as annealing process, Ni-rich Ni-Ti shape memory alloy wires were bent by V-shaped punches in different curvatures at room temperature. Subsequently, the wires were aged at different temperatures to have shape memory effect. As a result, springback was found after withdrawing the bending punch and further after the aging treatment as well. A higher solution treatment temperature or a smaller bending radius leads to a smaller springback, while a higher aging treatment temperature made a larger springback. This springback may be compensated by bending the wires in further larger curvatures to keep the shape accuracy as designed. To explore the shape memory effect, a reverse bending test was performed. It shows that all bent wires after aging had a shape recovery rate above 96.3% on average.

Study on Polylactide/Poly(ether block amide) Composite Biomaterials and Shape-Memory Effect

2009 ◽  
Vol 610-613 ◽  
pp. 1312-1314 ◽  
Author(s):  
Wei Zhang ◽  
Long Chen ◽  
Yu Zhang
Keyword(s):  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Tensile Load ◽  
Dissipation Process ◽  
Elongation At Break ◽  
High Deformation ◽  
Original Shape ◽  
As Stress ◽  
Heating Up

Melt blending of PLA and biodegradable PE-b-A has been performed in an effort to toughen the PLA. With the PE-b-A contents increasing, the elongation at break of composites increased and the brittle break became ductile break. When the PE-b-A content is 10%, the tensile strength of composite is similar with neat PLA, and the elongation increased significantly. The composites showed wonderful shape-memory effect. The composites occurred to deformation upon tensile load, and recovered to original shape quickly with temperature increasing. PE-b-A acts as stress concentrator in system with the stress release locally and energy-dissipation process. These will prevent PLA matrix from breaking under high deformation and make the PLA molecular orientation. Consequently, releasing the stress by heating up the material will reform the shape back to the original shape.

scholarly journals Fabrication and Two-Way Deformation of Shape Memory Composite with SMA and SMP

2010 ◽  
Vol 638-642 ◽  
pp. 2189-2194 ◽  
Author(s):  
Hisaaki Tobushi ◽  
Shunichi Hayashi ◽  
Y. Sugimoto ◽  
K. Date
Keyword(s):  
Shape Memory Alloy ◽  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Shape Memory Polymer ◽  
Bending Deformation ◽  
Heating And Cooling ◽  
Round Shape ◽  
Heat Treated ◽  
Shape Memory Composite

The shape memory composite (SMC) with shape memory alloy (SMA) and shape memory polymer (SMP) was fabricated, and the two-way bending deformation and recovery force were investigated. The results obtained can be summarized as follows. (1) Two kinds of SMA tapes which show the shape memory effect and superelasticity were heat-treated to memorize the round shape, respectively. The shape-memorized round SMA tapes were sandwiched between the SMP sheets, and the SMC belt was fabricated. (2) The two-way bending deformation with an angle of 56 degrees is observed during heating and cooling. (3) If the SMC belt is heated and cooled by keeping the form, recovery force increases during heating and decreases during cooling.

Synthesis and Characterization of IPDI Based Shape Memory Polyurethane

2020 ◽  
Vol 1010 ◽  
pp. 142-147
Author(s):  
Nur Athirah Rasli @ Rosli ◽  
Syazana Ahmad Zubir
Keyword(s):  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Soft Segment ◽  
Shape Memory Polymer ◽  
Palm Kernel ◽  
Hexamethylene Diisocyanate ◽  
Molar Ratio ◽  
Scanning Calorimetry ◽  
Chain Flexibility

Various polyurethane-based shape memory polymer was synthesized using polycaprolactone (PCL) as soft segment and, hexamethylene diisocyanate (HMDI) and isophorone diisocyanate (IPDI) as the hard segments. Palm kernel oil-based polyol was used to replace part of the petroleum-based polyol due to the increasing demand on renewable resources as a result of environmental awareness. The synthesis has been carried out using two step polymerization method. The effects of varying the molar ratio of IPDI/HMDI on material properties such as crystallinity, transition temperature, morphology, shape memory effect and tensile strength were investigated by using Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM), shape memory test and tensile test. A high IPDI content in SMPU results in better shape memory effect, whereas increasing HMDI content leads to a better chain flexibility. In this work, the incorporation of IPDI contributes to the formation of phase separation which enhance the formation of crystalline soft segment structure while the incorporation of HMDI as isocyanate tend to promote phase mixing which enhance the chain flexibility of the SMPU backbone.

Sign in / Sign up

Export Citation Format

Share Document