scholarly journals Modeling the Mechanical Response of Auxetic Metamaterials to Dynamic Effects

2021 ◽  
pp. 144-152
Author(s):  
V. V Skripnyak ◽  
M. O Chirkov ◽  
V. A Skripnyak
Keyword(s):  
Titanium Alloy ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Relative Density ◽  
Dynamic Loading ◽  
Uniaxial Compression ◽  
Mechanical Response ◽  
Effective Strain ◽  
Absorbed Energy ◽  
Auxetic Structure

The paper investigates the mechanical response of a 3D auxetic structure created on the basis of a unit cell with pre-buckled structural elements to dynamic loading. The aim of the work is to study deformations of the auxetic structure made of an alpha titanium alloy during uniaxial compression at 100 m/s, to evaluate dissipative properties of the structure during high-speed deformation, and to estimate the characteristic time of the metamaterial’s compaction with a relative density of 0.0115. The numerical simulation of the metamaterial at effective strain rate of 2000 1/s has been performed using LS DYNA solver. To describe the mechanical behavior of the titanium alloy in frame elements, we use a model of an elastic-plastic damaged medium, which takes into account the strain rate sensitivity of the plastic flow, temperature changes due to dissipative effects, and the effect of the stress state triaxiality parameter on nucleation and growth of structural damages. The numerical studies have shown that the auxetic effect in the studied metamaterial is retained under high-rate elastoplastic deformation. At a speed of the uniaxial compression of 100 m/s, deformation in the volume of the metamaterial proceeds nonuniformly. Under dynamic loading of the considered auxetic metamaterial, the deformation and fracture modes depend not only on the parameters of the cell geometry, but also on the mechanical behavior of the framework material, as well as on the relative density. This makes it possible to control the deformations of the cells under mechanical stress. Layers of compacted cells are formed near the dynamic loading surface. The instability of the cells of the auxetic metamaterials increases the absorbed energy. The calculated value of the specific absorbed energy under dynamic uniaxial compression reaches 3.4 kJ/kg, and is comparable with the values for frame structures made of Ti-6Al-4V with an equivalent specific mass density. The results indicate the possibility of creating protective structures using auxetic cellular structures on the base of the pre-buckled elements of the rolled metal.

On the Microstructural Characteristics of UFG Microalloyed Steel Influencing the Mechanical Behavior under Dynamic Loading

2018 ◽  
Vol 941 ◽  
pp. 39-45 ◽  
Author(s):  
Janusz Majta ◽  
Remigiusz Bloniarz ◽  
Marcin Kwiecień ◽  
Krzysztof Muszka
Keyword(s):  
Strain Rate ◽  
Mechanical Behavior ◽  
Dynamic Loading ◽  
Work Hardening ◽  
Mechanical Response ◽  
Thermomechanical Processing ◽  
Microalloyed Steel ◽  
Material Behavior ◽  
Second Phase ◽  
Loading Conditions

This paper presents a summary of a preliminary research aimed at producing ultrafine-grained (UFG) and heterogeneous microstructure in microalloyed steel and testing these materials under dynamic loading conditions (strain rates 800 s-1 and 1800s-1). The UFG and bimodal-structures, due to grain size, structural composition or morphology of structural components, were produced by an advanced thermomechanical processing, namely rolling in: hot, two-phase and cold-hot combined conditions. The advantage of bimodal microstructures is their maximization of mechanical behavior under extreme loading conditions due to promoted accumulation and interactions of geometrically necessary dislocations. The dynamic work-hardening behavior has been studied as a function of solute atoms and fine-scale, second-phase particles in the UFG and bimodal-structures. The substantial complexity of the phenomena, which occur through the evolution of microstructure and texture in response to dynamic loading, presents formidable challenges to theoretical model development of plastic deformation of UFG and bimodal-structures. Such an extraordinary work hardening provides an attractive strategy to develop optimal combination of mechanical properties i.e. strength/ductility ratio. A multi-scale analysis capable of including material behavior in different scales should be applied to discuss mechanical response of mentioned above microstructures and to help to analyze their influence on mechanical behavior under dynamic loading. The investigation was performed for a material of common application: high strength microalloyed steel X70. The experimental results show that strain rate sensitivity of the heterogeneous microstructures obtained by various thermomechanical rolling routes are significant, but not by a similar magnitude with the microstructure compositions and increasing strain rate.

scholarly journals Experimental Research on Mechanical and Energy Characteristics of Reinforced Rock under Dynamic Loading

2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Xinxi Liu ◽  
Yu Li ◽  
Fujun Zhao ◽  
Yanming Zhou ◽  
Weiwei Wang ◽  
...  
Keyword(s):  
Energy Dissipation ◽  
Strain Rate ◽  
Dynamic Loading ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Surrounding Rock ◽  
Absorbed Energy ◽  
Energy Characteristics ◽  
Deep Mining ◽  
The Stability

The properties of anchored surrounding rock may vary considerably under complex geological and stress conditions, especially dynamic loading in deep mining. Therefore, comprehensive study of the reinforced mechanism is required to prevent failures associated with deep mining. In this paper, with sandstone as matrix and steel bar as bolt, the dynamic compression test of reinforced rock was carried out by using a 50 mm rod diameter split Hopkinson pressure bar (SHPB) test device. The mechanical and energy characteristics of reinforced rock under dynamic loading were analyzed. The results show that the dynamic strength of reinforced sample is greater than that of unreinforced sample and increases with the increase of the strain rate. The reflected energy and absorbed energy increase with the increase of incident energy, while the transmitted energy increases slightly. The higher the strain rate, the larger the energy dissipation rate and the higher the degree of fragmentation. It shows that the energy dissipation characteristic reflects the internal damage process to some extent. Compared with the results of unreinforced samples, the reflected energy of reinforced samples significantly increases and the absorbed energy will significantly decrease. It can be seen that the bolt can reduce absorbed energy of surrounding rock, thereby improving the stability of roadway surrounding rock. The results may provide reference for the stability of deep roadway and support design.

scholarly journals Influence of strain rate on the mechanical response of nanostructured coppers elaborated by SPD and SPS

2021 ◽  
Vol 250 ◽  
pp. 03014
Author(s):  
Hervé Couque ◽  
Yuri Khoptiar ◽  
Frédéric Bernard ◽  
Itamar Gutman ◽  
Florian Bussiere ◽  
...  
Keyword(s):  
Strain Rate ◽  
Uniaxial Compression ◽  
Mechanical Response ◽  
Tensile Tests ◽  
Strain Rates ◽  
Static Compression ◽  
Plasma Sintering ◽  
History Of ◽  
Spark Plasma ◽  
Nanostructured Copper

The influence of strain rate on the mechanical response of two different nanostructured pure coppers was investigated under uniaxial compression. The first nanostructured copper was elaborated by powder metallurgy using the Spark Plasma Sintering (SPS) process. The second nanostructured copper was elaborated by Severe Plastic Deformation (SPD). Conventional characterizations were conducted with quasi-static compression and tensile tests, hardness tests and, with microstructure analysis. The effect of strain rate was evaluated under uniaxial compression at strain rates varying from 10-4 to 10+4 s-1. The high strain rate data were generated with a direct Hopkinson impact technique. The increase of strength with strain rates was analysed and discussed from the Scanning Electron Microscope observations and grain size distribution. The mechanical properties are consequently dependent on the metallurgical history of these samples prepared according to two different routes.

Microstructure and Texture in an Alpha/Beta Titanium Alloy and their Impact on Mechanical Response

2007 ◽  
Vol 539-543 ◽  
pp. 3589-3594
Author(s):  
W.J. Evans ◽  
F.R. Eng
Keyword(s):  
Titanium Alloy ◽  
Strain Rate ◽  
Titanium Alloys ◽  
Plane Strain ◽  
Basal Plane ◽  
Mechanical Response ◽  
Beta Titanium Alloy ◽  
Beta Titanium ◽  
Strain And Strain Rate ◽  
Alpha Beta

The paper explores texture in the titanium alloys Ti-6-4 and Ti 550. It illustrates how texture evolves under plane strain compression in Ti-6-4. This evolution is dependent on temperature, degree of reduction (strain) and strain rate. Rolled (Ti-6-4) and forged (Ti 550) variants with different textures are then examined under tension and torsion loading in relation to their monotonic and fatigue response. Correlation of the observations with regard to orientation of the basal plane is demonstrated.

Dynamic Tensile Tests of Auto-Body Steel Sheets with the Variation of Temperature

2006 ◽  
Vol 116-117 ◽  
pp. 259-262 ◽  
Author(s):  
Hee Jong Lee ◽  
Jung Han Song ◽  
Hoon Huh
Keyword(s):  
Flow Stress ◽  
Tensile Test ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
High Speed ◽  
Mechanical Response ◽  
Rate Sensitivity ◽  
Tensile Tests ◽  
Static State ◽  
Steel Sheets

This paper is concerned with the thermo-mechanical behavior of steel sheet for an autobody including the temperature dependent strain-rate sensitivity. Tensile tests have been carried out with the high strength steel sheets such as SPRC35R, SPRC45E and TRIP60. The tensile tests were performed with the variation of the strain-rates from 0.001/s to 200/s and with the variation of environmental temperatures from -40 to 200. The thermo-mechanical response at the quasi-static state is obtained with the static tensile test and the one at the intermediate strain-rate is obtained with the high speed tensile test. Both the strain-rate and the temperature sensitivity of the flow stress are calculated for the quantitative evaluation of thermo-mechanical behavior of steel sheets. The results demonstrate that as the strain-rate increases, the variation of the flow stress becomes more dependent on the temperature. The results also indicate that the material properties of SPRC35R are more sensitive to the strain-rate and the temperature than those of SPRC45E and TRIP60.

Mechanical Response of Human Muscle at Intermediate Strain Rates

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Xuedong Zhai ◽  
Eric A. Nauman ◽  
Yizhou Nie ◽  
Hangjie Liao ◽  
Roy J. Lycke ◽  
...  
Keyword(s):  
Strain Rate ◽  
Mechanical Behavior ◽  
Compressive Stress ◽  
Mechanical Response ◽  
Human Muscle ◽  
Fiber Direction ◽  
Strain Rates ◽  
Strain Response ◽  
Stress Strain ◽  
Intermediate Strain Rates

We experimentally determined the tensile stress–strain response of human muscle along fiber direction and compressive stress–strain response transverse to fiber direction at intermediate strain rates (100–102/s). A hydraulically driven material testing system with a dynamic testing mode was used to perform the tensile and compressive experiments on human muscle tissue. Experiments at quasi-static strain rates (below 100/s) were also conducted to investigate the strain-rate effects over a wider range. The experimental results show that, at intermediate strain rates, both the human muscle's tensile and compressive stress–strain responses are nonlinear and strain-rate sensitive. Human muscle also exhibits a stiffer and stronger tensile mechanical behavior along fiber direction than its compressive mechanical behavior along the direction transverse to fiber direction. An Ogden model with two material constants was adopted to describe the nonlinear tensile and compressive behaviors of human muscle.

Sign in / Sign up

Export Citation Format

Share Document