scholarly journals Experimental Research on Mechanical and Energy Characteristics of Reinforced Rock under Dynamic Loading

2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Xinxi Liu ◽  
Yu Li ◽  
Fujun Zhao ◽  
Yanming Zhou ◽  
Weiwei Wang ◽  
...  
Keyword(s):  
Energy Dissipation ◽  
Strain Rate ◽  
Dynamic Loading ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Surrounding Rock ◽  
Absorbed Energy ◽  
Energy Characteristics ◽  
Deep Mining ◽  
The Stability

The properties of anchored surrounding rock may vary considerably under complex geological and stress conditions, especially dynamic loading in deep mining. Therefore, comprehensive study of the reinforced mechanism is required to prevent failures associated with deep mining. In this paper, with sandstone as matrix and steel bar as bolt, the dynamic compression test of reinforced rock was carried out by using a 50 mm rod diameter split Hopkinson pressure bar (SHPB) test device. The mechanical and energy characteristics of reinforced rock under dynamic loading were analyzed. The results show that the dynamic strength of reinforced sample is greater than that of unreinforced sample and increases with the increase of the strain rate. The reflected energy and absorbed energy increase with the increase of incident energy, while the transmitted energy increases slightly. The higher the strain rate, the larger the energy dissipation rate and the higher the degree of fragmentation. It shows that the energy dissipation characteristic reflects the internal damage process to some extent. Compared with the results of unreinforced samples, the reflected energy of reinforced samples significantly increases and the absorbed energy will significantly decrease. It can be seen that the bolt can reduce absorbed energy of surrounding rock, thereby improving the stability of roadway surrounding rock. The results may provide reference for the stability of deep roadway and support design.

scholarly journals Dynamic Compression Damage Energy Consumption and Fractal Characteristics of Shale

2019 ◽  
Vol 2019 ◽  
pp. 1-7
Author(s):  
Guoliang Yang ◽  
Jingjiu Bi ◽  
Linian Ma
Keyword(s):  
Fractal Dimension ◽  
Energy Consumption ◽  
Energy Dissipation ◽  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Fractal Theory ◽  
Dissipated Energy ◽  
Impact Tests ◽  
The Impact

Studying the relationship between energy consumption and crushed size of shale under different loading conditions is the key to efficient shale cracking. The split Hopkinson pressure bar system was used to study the dynamic mechanical properties of shale under parallel- and vertical-bedding loading, and energy dissipation in the impact tests was calculated. Relationships between the average crushed size of shale fracture products and energy dissipation and between the fractal dimension and dissipated energy were studied using fractal theory. The experimental results showed that the dynamic compressive strength of shale under parallel- and vertical-bedding conditions had an obvious positive correlation with the strain rate. Dissipative energy of the shale samples under loading in both directions increased with the increase of strain rate. The increase of the strain rate enhanced crushing of the sample. The vertical-bedding shale samples had stronger ability to absorb energy and more internal crack propagation. Dissipative energies of the shale samples in the parallel- and vertical-bedding impact tests were positively related to the fractal dimension. The fractal dimension increased with the increase of dissipative energy during sample failure; with further increase in the dissipative energy, its effect on the change of fractal dimension gradually weakened.

Effect of Alkaline Treatment on Sawdust Reinforced High Density Polyethylene Composite under Wide Strain Rate

2016 ◽  
Vol 840 ◽  
pp. 103-107 ◽  
Author(s):  
Haliza Jaya ◽  
Mohd Firdaus Omar ◽  
Hazizan Md Akil ◽  
Zainal Arifin Ahmad ◽  
Nik Noriman Zulkepli
Keyword(s):  
Surface Roughness ◽  
Strain Rate ◽  
Dynamic Loading ◽  
High Density Polyethylene ◽  
Split Hopkinson Pressure Bar ◽  
Alkali Treatment ◽  
Testing Machine ◽  
High Density ◽  
Rate Condition ◽  
Static And Dynamic Loading

In this study, the alkali treatment of sawdust using different concentration of sodium hydroxide (NaOH) is performed. The purpose of this treatment is to improve the filler-matrix compatibility, thus, enhance the properties of tested specimens under various strain rate condition. The outcome shows the alkali treated sawdust did improve its surface roughness through reduction of sawdust diameter. With this increasing of surface roughness, it will enhance the compatibility between sawdust filler and HDPE matrix. For comparison purpose, the treated and untreated sawdust filler were reinforce in High Density Polyethylene (HDPE) matrix and have been test under static and dynamic loading using Universal Testing Machine (UTM) and Split Hopkinson Pressure Bar (SHPB) apparatus. The results indicate that the stiffness and compression strength properties were improved on treated sawdust composites for both static and dynamic loading compare to untreated sawdust composites.

Microstructures and Dynamic Compression Properties of a High Reinforcement Content TiB2/Al Composite

2007 ◽  
Vol 546-549 ◽  
pp. 639-642
Author(s):  
De Zhi Zhu ◽  
Gao Hui Wu ◽  
Long Tao Jiang ◽  
Guo Qin Chen
Keyword(s):  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Shear Fracture ◽  
Dynamic Compression ◽  
Average Particle Size ◽  
Average Particle ◽  
Hopkinson Pressure Bar ◽  
Compression Properties ◽  
Reinforcement Content ◽  
Al Composite

A high reinforcement content TiB2/2024Al composite with an average particle size of 8μm was fabricated by squeeze casting technology. The dynamic compression behaviors of the composite under varied strain rates were measured using split Hopkinson pressure bar, and its microstructure and fracture characteristic were examined. Resluts revealed that the composite was dense and homogenerous, and the TiB2-Al interface was clean without interfacial reactants. At high strain rate, the TiB2/Al composite showed insensitive to the strain rate, and both the flow stress and the elastic modulus improved little with an increase of the strain rate. The composite failed macroscopically in shear fracture and in split, which were caused by cracking of large reinforcement particles and interface failures under dynamic load.

High Strain Rate Response of Rocks Under Dynamic Loading Using Split Hopkinson Pressure Bar

2017 ◽  
Vol 36 (1) ◽  
pp. 531-549 ◽  
Author(s):  
Sunita Mishra ◽  
Hemant Meena ◽  
Vedant Parashar ◽  
Anuradha Khetwal ◽  
Tanusree Chakraborty ◽  
...  
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Dynamic Loading ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Hopkinson Pressure Bar ◽  
Split Hopkinson ◽  
Pressure Bar

scholarly journals High strain rate behaviour of fiber reinforced concrete

2018 ◽  
Vol 183 ◽  
pp. 02012
Author(s):  
Miloslav Popovič ◽  
Jaroslav Buchar ◽  
Martina Drdlová
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Speed ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Fiber Reinforced Concrete ◽  
Hopkinson Pressure Bar ◽  
Static Test ◽  
Pressure Bar

The results of dynamic compression and tensile-splitting tests of concrete reinforced by randomly distributed short non – metallic fibres are presented. A Split Hopkinson Pressure Bar combined with a high-speed photographic system, was used to conduct dynamic Brazilian tests. Quasi static test show that the reinforcement of concrete by the non-metallic fibres leads to the improvement of mechanical properties at quasi static loading. This phenomenon was not observed at the high strain rate loading .Some explanation of this result is briefly outlined.

Strain-Rate Relationship of Aluminum Matrix Composites Predicted by Johnson-Cook Model

2011 ◽  
Vol 704-705 ◽  
pp. 935-940
Author(s):  
De Zhi Zhu ◽  
Wei Ping Chen ◽  
Yuan Yuan Li
Keyword(s):  
Strain Rate ◽  
Volume Fraction ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Aluminum Matrix ◽  
Rate Sensitivity ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Hopkinson Pressure Bar ◽  
Cook Model

Strain-rate sensitivities of 55-65vol.% aluminum 2024-T6/TiB2composites and the corresponding aluminum 2024-T6 matrix were investigated using split Hopkinson pressure bar. Results showed that 55-65vol.% aluminum 2024-T6/TiB2composites exhibited significant strain-rate sensitivities, which were three times higher than that of the aluminum 2024-T6 matrix. The strain-rate sensitivity of the aluminum 2024-T6 matrix composites rose obviously with reinforcement content increasing (up to 60%), which agreed with the previous researches. The aluminum 2024-T6/TiB2composites showed hybrid fracture characteristics including particle cracking and aluminum alloy softening under dynamic loading. The flow stresses predicted by Johnson-Cook model increased slowly when the reinforcement volume fraction ranged in 10%-40%. While the reinforcement volume fraction was over 40%, the flow stresses of aluminum matrix composites increased obviously and the strains dropped sharply. Keywords: Composite materials; Dynamic compression; Stress-strain relationship

Strain-Rate Dependence of Compressive Yield Strength of Titanium Grade 4 with Coarse-Grained and Ultrafine-Grained Structures: Experimental Results and Theoretical Calculation

2018 ◽  
Vol 1145 ◽  
pp. 100-105
Author(s):  
Ivan V. Smirnov ◽  
Alexander Y. Konstantinov
Keyword(s):  
Yield Strength ◽  
Strain Rate ◽  
Yield Stress ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Pure Titanium ◽  
Coarse Grained ◽  
Strain Rates ◽  
Ultrafine Grained ◽  
Titanium Grade

The nanocrystalline (NC) and ultrafine-grained (UFG) structures of metallic materials can lead to their extraordinary high strength. However, most of the papers on this topic consider deformation parameters of NC and UFG materials only for the case of quasi-static tensile tests. Characteristics of dynamic strength and fracture of such materials remain unexplored. This paper presents a study of the mechanical behavior of pure titanium Grade 4 with a coarse-grained (CG) and UFG structure under uniaxial compression with different strain rates. The UFG structure was provided using the method of equal-channel angular pressing. The dynamic compression was carried out on a setup with the Split-Hopkinson pressure bar. It is found that in the observed range of strain rates 10–3-3×103 s–1, the yield stress of the CG titanium increases by 20%, and does not exceed the yield stress of the UFG titanium. However, the yield stress of the UFG titanium remains close to a quasi-static value. It is shown that these strain-rate dependencies of the yield strength can be predicted by the incubation time approach. The calculated curves show that at strain rates above 104 s–1 the yield stress of the CG titanium becomes higher than the yield strength of the UFG titanium.

High strain-rate behavior of natural fiber-reinforced polymer composites

2011 ◽  
Vol 46 (9) ◽  
pp. 1051-1065 ◽  
Author(s):  
Wonsuk Kim ◽  
Alan Argento ◽  
Ellen Lee ◽  
Cynthia Flanigan ◽  
Daniel Houston ◽  
...  
Keyword(s):  
Energy Dissipation ◽  
High Strain Rate ◽  
Strain Rate ◽  
Polymer Composites ◽  
Natural Fiber ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Natural Fibers ◽  
Hopkinson Pressure Bar ◽  
Stress Strain

The high strain-rate constitutive behavior of polymer composites with various natural fibers is studied. Hemp, hemp/glass hybrid, cellulose, and wheat straw-reinforced polymeric composites have been manufactured, and a split-Hopkinson pressure bar apparatus has been designed to measure the dynamic stress–strain response of the materials. Using the apparatus, compressive stress–strain curves have been obtained that reveal the materials’ constitutive characteristics at strain rates between 600 and 2400 strain/s. Primary findings indicate that natural fibers in thermoset composites dissipate energy at lower levels of stress and higher strain than glass-reinforced composites. In the case of thermoplastic matrices, the effect on energy dissipation of natural fibers vs. conventional talc reinforcements is highly dependent on resin properties. Natural fibers in polypropylene homopolymer show improved reinforcement but have degraded energy dissipation compared to talc. Whereas in polypropylene copolymer, natural fibers result in improved energy dissipation compared to talc. These data are useful for proper design, analysis, and simulation of lightweight biocomposites.

Dynamic Compression Performance of Reaction Sintering SiC/B4C Composite

2020 ◽  
Vol 999 ◽  
pp. 83-90
Author(s):  
Xiao Ju Gao ◽  
Hasigaowa ◽  
Meng Yong Sun ◽  
Cheng Dong Liao ◽  
Wei Ping Huang ◽  
...  
Keyword(s):  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Dynamic Strength ◽  
Reaction Sintering ◽  
Hopkinson Pressure Bar ◽  
Compression Performance ◽  
Loading Mode ◽  
Split Hopkinson ◽  
Pressure Bar

SiC/B4C composite was obtained using the reaction sintering method with Si infiltration, which exhibited excellent mechanical properties. The dynamic compressive response was investigated using a Split Hopkinson pressure bar at high strain rates ranging from 0.4×103 to 1.2×103 s-1. The results show that the dynamic strength of the SiC/B4C composite obtains a peak value at a strain rate of 1000/s, while its strain increased continuously with increasing strain rate. The dynamic loading mode of SiC/B4C composite exhibited three deformation regions, including an inelastic deformation region, rapid loading region and failure region. The dynamic failure mode of SiC/B4C composite depended upon the strain rate.

High Strain Rate Behavior of Carbon Nanotubes Reinforced Aluminum Foams

2017 ◽  
Vol 140 (1) ◽  
Author(s):  
Abdelhakim Aldoshan ◽  
D. P. Mondal ◽  
Sanjeev Khanna
Keyword(s):  
Carbon Nanotubes ◽  
Strain Rate ◽  
Aluminum Foam ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Strain Rates ◽  
Aluminum Foams ◽  
Static Compression ◽  
Closed Cell

The mechanical behavior of closed-cell aluminum foam composites under different compressive loadings has been investigated. Closed-cell aluminum foam composites made using the liquid metallurgy route were reinforced with multiwalled carbon nanotubes (CNTs) with different concentrations, namely, 1%, 2%, and 3% by weight. The reinforced foams were experimentally tested under dynamic compression using the split Hopkinson pressure bar (SHPB) system over a range of strain rates (up to 2200 s−1). For comparison, aluminum foams were also tested under quasi-static compression. It was observed that closed-cell aluminum foam composites are strain rate sensitive. The mechanical properties of CNT reinforced Al-foams, namely, yield stress, plateau stress, and energy absorption capacity are significantly higher than that of monolithic Al-foam under both low and high strain rates.

Sign in / Sign up

Export Citation Format

Share Document