TOMOGRAPHIC RECONSTRUCTION OF ASYMMETRIC SPRAYS FROM A TWIN-HOLE AIR SHROUD INJECTOR

1997 ◽  
Vol 7 (2) ◽  
pp. 183-197 ◽  
Author(s):  
Changhyuk Lee ◽  
Suk Ho Chung
Keyword(s):  
Tomographic Reconstruction

Design and calibration of an IVEM for general 3-dimensional imaging of non-diffracting materials

1992 ◽  
Vol 50 (2) ◽  
pp. 1040-1041
Author(s):  
Neil Rowlands ◽  
Jeff Price ◽  
Michael Kersker ◽  
Seichi Suzuki ◽  
Steve Young ◽  
...  
Keyword(s):  
3D Imaging ◽  
Tomographic Reconstruction ◽  
Three Dimensional ◽  
3 Dimensional ◽  
3D Microstructure ◽  
Image Translation ◽  
Digital Correlation ◽  
On Line ◽  
Mechanical Stage ◽  
Projection Angle

Three-dimensional (3D) microstructure visualization on the electron microscope requires that the sample be tilted to different positions to collect a series of projections. This tilting should be performed rapidly for on-line stereo viewing and precisely for off-line tomographic reconstruction. Usually a projection series is collected using mechanical stage tilt alone. The stereo pairs must be viewed off-line and the 60 to 120 tomographic projections must be aligned with fiduciary markers or digital correlation methods. The delay in viewing stereo pairs and the alignment problems in tomographic reconstruction could be eliminated or improved by tilting the beam if such tilt could be accomplished without image translation.A microscope capable of beam tilt with simultaneous image shift to eliminate tilt-induced translation has been investigated for 3D imaging of thick (1 μm) biologic specimens. By tilting the beam above and through the specimen and bringing it back below the specimen, a brightfield image with a projection angle corresponding to the beam tilt angle can be recorded (Fig. 1a).

Methods for three-dimensional reconstruction of cellular components within a thick section

1986 ◽  
Vol 44 ◽  
pp. 18-21
Author(s):  
J. Frank ◽  
B. F. McEwen ◽  
M. Radermacher ◽  
C. L. Rieder
Keyword(s):  
Tilt Angle ◽  
Tomographic Reconstruction ◽  
3D Structure ◽  
Three Dimensional ◽  
Thick Section ◽  
Three Dimensional Reconstruction ◽  
Axis Ratio ◽  
Dimensional Reconstruction ◽  
Cellular Components

The tomographic reconstruction from multiple projections of cellular components, within a thick section, offers a way of visualizing and quantifying their three-dimensional (3D) structure. However, asymmetric objects require as many views from the widest tilt range as possible; otherwise the reconstruction may be uninterpretable. Even if not for geometric obstructions, the increasing pathway of electrons, as the tilt angle is increased, poses the ultimate upper limitation to the projection range. With the maximum tilt angle being fixed, the only way to improve the faithfulness of the reconstruction is by changing the mode of the tilting from single-axis to conical; a point within the object projected with a tilt angle of 60° and a full 360° azimuthal range is then reconstructed as a slightly elliptic (axis ratio 1.2 : 1) sphere.

Practical electron tomography

1995 ◽  
Vol 53 ◽  
pp. 742-743
Author(s):  
C.L. Woodcock
Keyword(s):  
Electron Tomography ◽  
Tomographic Reconstruction ◽  
Three Dimensional ◽  
3D Shape ◽  
Computational Resources ◽  
Shape Of Particles

Despite the potential of the technique, electron tomography has yet to be widely used by biologists. This is in part related to the rather daunting list of equipment and expertise that are required. Thanks to continuing advances in theory and instrumentation, tomography is now more feasible for the non-specialist. One barrier that has essentially disappeared is the expense of computational resources. In view of this progress, it is time to give more attention to practical issues that need to be considered when embarking on a tomographic project. The following recommendations and comments are derived from experience gained during two long-term collaborative projects.Tomographic reconstruction results in a three dimensional description of an individual EM specimen, most commonly a section, and is therefore applicable to problems in which ultrastructural details within the thickness of the specimen are obscured in single micrographs. Information that can be recovered using tomography includes the 3D shape of particles, and the arrangement and dispostion of overlapping fibrous and membranous structures.

Laser tomographic reconstruction in a complex concentration flow field

1999 ◽  
Author(s):  
Jisoo Ha ◽  
Michael Feng ◽  
Frederick Gouldin
Keyword(s):  
Flow Field ◽  
Tomographic Reconstruction

X-Ray Nanotomography (XRMT) Tool for Non-Destructive High-Resolution Imaging of ICs

2001 ◽  
Author(s):  
Wenbing Yun ◽  
Steve Wang ◽  
David Scott ◽  
Kenneth W. Nill ◽  
Waleed S. Haddad
Keyword(s):  
High Resolution ◽  
Process Development ◽  
3D Visualization ◽  
Tomographic Reconstruction ◽  
Reconstruction Algorithms ◽  
X Ray ◽  
Visualization Software ◽  
Volumetric Reconstruction ◽  
Resolution Imaging ◽  
Non Destructive

Abstract A high-resolution table-sized x-ray nanotomography (XRMT) tool has been constructed that shows the promise of nondestructively imaging the internal structure of a full IC stack with a spatial resolution better than 100 nm. Such a tool can be used to detect, localize, and characterize buried defects in the IC. By collecting a set of X-ray projections through the full IC (which may include tens of micrometers of silicon substrate and several layers of Cu interconnects) and applying tomographic reconstruction algorithms to these projections, a 3D volumetric reconstruction can be obtained, and analyzed for defects using 3D visualization software. XRMT is a powerful technique that will find use in failure analysis and IC process development, and may facilitate or supplant investigations using SEM, TEM, and FIB tools, which generally require destructive sample preparation and a vacuum environment.

scholarly journals Dense U-Net for Limited Angle Tomography of Sound Pressure Fields

2021 ◽  
Vol 11 (10) ◽  
pp. 4570
Author(s):  
Oliver Rothkamm ◽  
Johannes Gürtler ◽  
Jürgen Czarske ◽  
Robert Kuschmierz
Keyword(s):  
Measurement Errors ◽  
Sound Pressure ◽  
Tomographic Reconstruction ◽  
Synthetic Data ◽  
Projection Data ◽  
Quantitative Measurements ◽  
Pressure Fields ◽  
The Neural Network ◽  
Bias Flow ◽  
3D Information

Tomographic reconstruction allows for the recovery of 3D information from 2D projection data. This commonly requires a full angular scan of the specimen. Angular restrictions that exist, especially in technical processes, result in reconstruction artifacts and unknown systematic measurement errors. We investigate the use of neural networks for extrapolating the missing projection data from holographic sound pressure measurements. A bias flow liner was studied for active sound dampening in aviation. We employed a dense U-Net trained on synthetic data and compared reconstructions of simulated and measured data with and without extrapolation. In both cases, the neural network based approach decreases the mean and maximum measurement deviations by a factor of two. These findings can enable quantitative measurements in other applications suffering from limited angular access as well.

scholarly journals Correction for the Partial Volume Effects (PVE) in Nuclear Medicine Imaging: A Post-Reconstruction Analytic Method

2021 ◽  
Vol 11 (14) ◽  
pp. 6460
Author(s):  
Fabio Di Martino ◽  
Patrizio Barca ◽  
Eleonora Bortoli ◽  
Alessia Giuliano ◽  
Duccio Volterrani
Keyword(s):  
Nuclear Medicine ◽  
Imaging System ◽  
Tomographic Reconstruction ◽  
Mathematical Expression ◽  
Reconstruction Algorithm ◽  
Volume Effect ◽  
Nuclear Medicine Imaging ◽  
Theoretical Derivation ◽  
Reconstruction Process ◽  
Partial Volume

Quantitative analyses in nuclear medicine are increasingly used, both for diagnostic and therapeutic purposes. The Partial Volume Effect (PVE) is the most important factor of loss of quantification in Nuclear Medicine, especially for evaluation in Region of Interest (ROI) smaller than the Full Width at Half Maximum (FWHM) of the PSF. The aim of this work is to present a new approach for the correction of PVE, using a post-reconstruction process starting from a mathematical expression, which only requires the knowledge of the FWHM of the final PSF of the imaging system used. After the presentation of the theoretical derivation, the experimental evaluation of this method is performed using a PET/CT hybrid system and acquiring the IEC NEMA phantom with six spherical “hot” ROIs (with diameters of 10, 13, 17, 22, 28, and 37 mm) and a homogeneous “colder” background. In order to evaluate the recovery of quantitative data, the effect of statistical noise (different acquisition times), tomographic reconstruction algorithm with and without time-of-flight (TOF) and different signal-to-background activity concentration ratio (3:1 and 10:1) was studied. The application of the corrective method allows recovering the loss of quantification due to PVE for all sizes of spheres acquired, with a final accuracy less than 17%, for lesion dimensions larger than two FWHM and for acquisition times equal to or greater than two minutes.

Characteristics of tomographic reconstruction of light-field Tomo-PIV

2019 ◽  
Vol 442 ◽  
pp. 132-147 ◽  
Author(s):  
Lixia Cao ◽  
Biao Zhang ◽  
Jian Li ◽  
Xianglei Song ◽  
Zhiyong Tang ◽  
...  
Keyword(s):  
Light Field ◽  
Tomographic Reconstruction

Evaluation of Algorithms for Tomographic Reconstruction of Chemical Concentrations in Indoor Air

AIHAJ ◽  
1994 ◽  
Vol 55 (5) ◽  
pp. 403-417 ◽  
Author(s):  
L. Todd ◽  
G. Ramachandran
Keyword(s):  
Indoor Air ◽  
Tomographic Reconstruction

scholarly journals High-resolution limited-angle phase tomography of dense layered objects using deep neural networks

2019 ◽  
Vol 116 (40) ◽  
pp. 19848-19856 ◽  
Author(s):  
Alexandre Goy ◽  
Girish Rughoobur ◽  
Shuai Li ◽  
Kwabena Arthur ◽  
Akintunde I. Akinwande ◽  
...  
Keyword(s):  
Integrated Circuit ◽  
Deep Neural Networks ◽  
Tomographic Reconstruction ◽  
Synthetic Data ◽  
Single Step ◽  
Training Set ◽  
Step Method ◽  
3 Dimensional ◽  
Dimensional Reconstruction ◽  
Optical Domain

We present a machine learning-based method for tomographic reconstruction of dense layered objects, with range of projection angles limited to ±10○. Whereas previous approaches to phase tomography generally require 2 steps, first to retrieve phase projections from intensity projections and then to perform tomographic reconstruction on the retrieved phase projections, in our work a physics-informed preprocessor followed by a deep neural network (DNN) conduct the 3-dimensional reconstruction directly from the intensity projections. We demonstrate this single-step method experimentally in the visible optical domain on a scaled-up integrated circuit phantom. We show that even under conditions of highly attenuated photon fluxes a DNN trained only on synthetic data can be used to successfully reconstruct physical samples disjoint from the synthetic training set. Thus, the need for producing a large number of physical examples for training is ameliorated. The method is generally applicable to tomography with electromagnetic or other types of radiation at all bands.

Sign in / Sign up

Export Citation Format

Share Document