Design and calibration of an IVEM for general 3-dimensional imaging of non-diffracting materials

1992 ◽  
Vol 50 (2) ◽  
pp. 1040-1041
Author(s):  
Neil Rowlands ◽  
Jeff Price ◽  
Michael Kersker ◽  
Seichi Suzuki ◽  
Steve Young ◽  
...  
Keyword(s):  
3D Imaging ◽  
Tomographic Reconstruction ◽  
Three Dimensional ◽  
3 Dimensional ◽  
3D Microstructure ◽  
Image Translation ◽  
Digital Correlation ◽  
On Line ◽  
Mechanical Stage ◽  
Projection Angle

Three-dimensional (3D) microstructure visualization on the electron microscope requires that the sample be tilted to different positions to collect a series of projections. This tilting should be performed rapidly for on-line stereo viewing and precisely for off-line tomographic reconstruction. Usually a projection series is collected using mechanical stage tilt alone. The stereo pairs must be viewed off-line and the 60 to 120 tomographic projections must be aligned with fiduciary markers or digital correlation methods. The delay in viewing stereo pairs and the alignment problems in tomographic reconstruction could be eliminated or improved by tilting the beam if such tilt could be accomplished without image translation.A microscope capable of beam tilt with simultaneous image shift to eliminate tilt-induced translation has been investigated for 3D imaging of thick (1 μm) biologic specimens. By tilting the beam above and through the specimen and bringing it back below the specimen, a brightfield image with a projection angle corresponding to the beam tilt angle can be recorded (Fig. 1a).

scholarly journals Three-dimensional imaging of hold baggage for airport security

2014 ◽  
Vol XL-5 ◽  
pp. 331-336
Author(s):  
S. Kolokytha ◽  
R. Speller ◽  
S. Robson
Keyword(s):  
3D Imaging ◽  
Imaging System ◽  
Tomographic Reconstruction ◽  
Three Dimensional ◽  
Handling Time ◽  
Cost Effective ◽  
Airport Security ◽  
X Ray ◽  
Common System ◽  
Close Range

This study describes a cost-effective check-in baggage screening system, based on "on-belt tomosynthesis" (ObT) and close-range photogrammetry, that is designed to address the limitations of the most common system used, conventional projection radiography. The latter's limitations can lead to loss of information and an increase in baggage handling time, as baggage is manually searched or screened with more advanced systems. This project proposes a system that overcomes such limitations creating a cost-effective automated pseudo-3D imaging system, by combining x-ray and optical imaging to form digital tomograms. Tomographic reconstruction requires a knowledge of the change in geometry between multiple x-ray views of a common object. This is uniquely achieved using a close range photogrammetric system based on a small network of web-cameras. This paper presents the recent developments of the ObT system and describes recent findings of the photogrammetric system implementation. Based on these positive results, future work on the advancement of the ObT system as a cost-effective pseudo-3D imaging of hold baggage for airport security is proposed.

Three-Dimensional Reconstruction Using Stereo Pairs from Serial Thick Sections

1977 ◽  
Vol 35 ◽  
pp. 562-563
Author(s):  
Robert Glaeser ◽  
Thomas Bauer ◽  
David Grano
Keyword(s):  
Three Dimensional ◽  
Dimensional Structure ◽  
Serial Sections ◽  
Thin Sections ◽  
3 Dimensional ◽  
Transmission Electron ◽  
Freeze Dried ◽  
Dimensional Reconstruction ◽  
Stereo Imagery ◽  
Whole Mounts

In transmission electron microscopy, the 3-dimensional structure of an object is usually obtained in one of two ways. For objects which can be included in one specimen, as for example with elements included in freeze- dried whole mounts and examined with a high voltage microscope, stereo pairs can be obtained which exhibit the 3-D structure of the element. For objects which can not be included in one specimen, the 3-D shape is obtained by reconstruction from serial sections. However, without stereo imagery, only detail which remains constant within the thickness of the section can be used in the reconstruction; consequently, the choice is between a low resolution reconstruction using a few thick sections and a better resolution reconstruction using many thin sections, generally a tedious chore. This paper describes an approach to 3-D reconstruction which uses stereo images of serial thick sections to reconstruct an object including detail which changes within the depth of an individual thick section.

Methods for three-dimensional reconstruction of cellular components within a thick section

1986 ◽  
Vol 44 ◽  
pp. 18-21
Author(s):  
J. Frank ◽  
B. F. McEwen ◽  
M. Radermacher ◽  
C. L. Rieder
Keyword(s):  
Tilt Angle ◽  
Tomographic Reconstruction ◽  
3D Structure ◽  
Three Dimensional ◽  
Thick Section ◽  
Three Dimensional Reconstruction ◽  
Axis Ratio ◽  
Dimensional Reconstruction ◽  
Cellular Components

The tomographic reconstruction from multiple projections of cellular components, within a thick section, offers a way of visualizing and quantifying their three-dimensional (3D) structure. However, asymmetric objects require as many views from the widest tilt range as possible; otherwise the reconstruction may be uninterpretable. Even if not for geometric obstructions, the increasing pathway of electrons, as the tilt angle is increased, poses the ultimate upper limitation to the projection range. With the maximum tilt angle being fixed, the only way to improve the faithfulness of the reconstruction is by changing the mode of the tilting from single-axis to conical; a point within the object projected with a tilt angle of 60° and a full 360° azimuthal range is then reconstructed as a slightly elliptic (axis ratio 1.2 : 1) sphere.

Practical electron tomography

1995 ◽  
Vol 53 ◽  
pp. 742-743
Author(s):  
C.L. Woodcock
Keyword(s):  
Electron Tomography ◽  
Tomographic Reconstruction ◽  
Three Dimensional ◽  
3D Shape ◽  
Computational Resources ◽  
Shape Of Particles

Despite the potential of the technique, electron tomography has yet to be widely used by biologists. This is in part related to the rather daunting list of equipment and expertise that are required. Thanks to continuing advances in theory and instrumentation, tomography is now more feasible for the non-specialist. One barrier that has essentially disappeared is the expense of computational resources. In view of this progress, it is time to give more attention to practical issues that need to be considered when embarking on a tomographic project. The following recommendations and comments are derived from experience gained during two long-term collaborative projects.Tomographic reconstruction results in a three dimensional description of an individual EM specimen, most commonly a section, and is therefore applicable to problems in which ultrastructural details within the thickness of the specimen are obscured in single micrographs. Information that can be recovered using tomography includes the 3D shape of particles, and the arrangement and dispostion of overlapping fibrous and membranous structures.

Analyzing the Impact of X-Ray Tomography on the Reliability of Integrated Circuits

2015 ◽  
Author(s):  
Halit Dogan ◽  
Md Mahbub Alam ◽  
Navid Asadizanjani ◽  
Sina Shahbazmohamadi ◽  
Domenic Forte ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Integrated Circuit ◽  
3D Imaging ◽  
Three Dimensional ◽  
Serial Sectioning ◽  
Promising Technique ◽  
Flash Memories ◽  
X Ray ◽  
3D Information ◽  
The Impact

Abstract X-ray tomography is a promising technique that can provide micron level, internal structure, and three dimensional (3D) information of an integrated circuit (IC) component without the need for serial sectioning or decapsulation. This is especially useful for counterfeit IC detection as demonstrated by recent work. Although the components remain physically intact during tomography, the effect of radiation on the electrical functionality is not yet fully investigated. In this paper we analyze the impact of X-ray tomography on the reliability of ICs with different fabrication technologies. We perform a 3D imaging using an advanced X-ray machine on Intel flash memories, Macronix flash memories, Xilinx Spartan 3 and Spartan 6 FPGAs. Electrical functionalities are then tested in a systematic procedure after each round of tomography to estimate the impact of X-ray on Flash erase time, read margin, and program operation, and the frequencies of ring oscillators in the FPGAs. A major finding is that erase times for flash memories of older technology are significantly degraded when exposed to tomography, eventually resulting in failure. However, the flash and Xilinx FPGAs of newer technologies seem less sensitive to tomography, as only minor degradations are observed. Further, we did not identify permanent failures for any chips in the time needed to perform tomography for counterfeit detection (approximately 2 hours).

scholarly journals Hyperspectral Three-Dimensional Fluorescence Imaging Using Snapshot Optical Tomography

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3652
Author(s):  
Cory Juntunen ◽  
Isabel M. Woller ◽  
Yongjin Sung
Keyword(s):  
Fourier Transform ◽  
3D Imaging ◽  
Optical Tomography ◽  
Three Dimensional ◽  
High Spectral Resolution ◽  
Functional Information ◽  
Fluorescent Beads ◽  
Different Depths ◽  
Projection Images ◽  
Imaging Performance

Hyperspectral three-dimensional (3D) imaging can provide both 3D structural and functional information of a specimen. The imaging throughput is typically very low due to the requirement of scanning mechanisms for different depths and wavelengths. Here we demonstrate hyperspectral 3D imaging using Snapshot projection optical tomography (SPOT) and Fourier-transform spectroscopy (FTS). SPOT allows us to instantaneously acquire the projection images corresponding to different viewing angles, while FTS allows us to perform hyperspectral imaging at high spectral resolution. Using fluorescent beads and sunflower pollens, we demonstrate the imaging performance of the developed system.

scholarly journals Comparative Study of Silk Fibroin-Based Hydrogels and Their Potential as Material for 3-Dimensional (3D) Printing

Molecules ◽  
2021 ◽  
Vol 26 (13) ◽  
pp. 3887
Author(s):  
Watcharapong Pudkon ◽  
Chavee Laomeephol ◽  
Siriporn Damrongsakkul ◽  
Sorada Kanokpanont ◽  
Juthamas Ratanavaraporn
Keyword(s):  
3D Printing ◽  
Silk Fibroin ◽  
Biomedical Applications ◽  
Mechanical Stability ◽  
Three Dimensional ◽  
Structure Stability ◽  
3 Dimensional ◽  
Critical Technology ◽  
Box Structure ◽  
High Degree

Three-dimensional (3D) printing is regarded as a critical technology in material engineering for biomedical applications. From a previous report, silk fibroin (SF) has been used as a biomaterial for tissue engineering due to its biocompatibility, biodegradability, non-toxicity and robust mechanical properties which provide a potential as material for 3D-printing. In this study, SF-based hydrogels with different formulations and SF concentrations (1–3%wt) were prepared by natural gelation (SF/self-gelled), sodium tetradecyl sulfate-induced (SF/STS) and dimyristoyl glycerophosphorylglycerol-induced (SF/DMPG). From the results, 2%wt SF-based (2SF) hydrogels showed suitable properties for extrusion, such as storage modulus, shear-thinning behavior and degree of structure recovery. The 4-layer box structure of all 2SF-based hydrogel formulations could be printed without structural collapse. In addition, the mechanical stability of printed structures after three-step post-treatment was investigated. The printed structure of 2SF/STS and 2SF/DMPG hydrogels exhibited high stability with high degree of structure recovery as 70.4% and 53.7%, respectively, compared to 2SF/self-gelled construct as 38.9%. The 2SF/STS and 2SF/DMPG hydrogels showed a great potential to use as material for 3D-printing due to its rheological properties, printability and structure stability.

Clinical Utility of an Exoskeleton Robot Using 3-Dimensional Scanner Modeling in Burn Patient: A Case Report

2021 ◽  
Author(s):  
So Young Joo ◽  
Seung Yeol Lee ◽  
Yoon Soo Cho ◽  
Sangho Yi ◽  
Cheong Hoon Seo
Keyword(s):  
Burn Injury ◽  
Hand Function ◽  
Three Dimensional ◽  
The Body ◽  
3D Technology ◽  
Early Management ◽  
3 Dimensional ◽  
Exoskeleton Robot ◽  
Physical Abilities ◽  
Upper Limb Dysfunction

Abstract Hands are the part of the body that are most commonly involved in burns, and the main complications are finger joint contractures and nerve injuries. Hypertrophic scarring cannot be avoided despite early management of acute hand burn injuries, and some patients may need application of an exoskeleton robot to restore hand function. To do this, it is essential to individualize the customization of the robot for each patient. Three-dimensional (3D) technology, which is widely used in the field of implants, anatomical models, and tissue fabrication, makes this goal achievable. Therefore, this report is a study on the usefulness of an exoskeleton robot using 3D technology for patients who lost bilateral hand function due to burn injury. Our subject was a 45-year-old man with upper limb dysfunction of 560 days after a flame and chemical burn injury, with resultant impairment of manual physical abilities. After wearing an exoskeleton robot made using 3D printing technology, he could handle objects effectively and satisfactorily. This innovative approach provided considerable advantages in terms of customization of size and reduction in manufacturing time and costs, thereby showing great potential for use in patients with hand dysfunction after burn injury.

scholarly journals Accuracy and Reliability of Soft Tissue Landmarks Using Three-Dimensional Imaging in Comparison With Two-Dimensional Cephalometrics: A Systematic Review

2020 ◽  
Vol 54 (4) ◽  
pp. 289-296
Author(s):  
Adeeba Ali ◽  
Anil K. Chandna ◽  
Anshul Munjal
Keyword(s):  
Systematic Review ◽  
Soft Tissue ◽  
3D Imaging ◽  
Soft Tissues ◽  
Three Dimensional ◽  
Database Search ◽  
Cochrane Library ◽  
Two Dimensional ◽  
Imaging Tool ◽  
Electronic Database Search

Background: Concerns about the accuracy and reliability of soft tissue landmarks using two-dimensional (2D) and three-dimensional (3D) imaging. Objective: The aim of the systematic review is to estimate accuracy and reliability of soft tissue landmarks with 2D imaging and 3D imaging for orthodontic diagnosis planning and treatment planning purposes. Data Sources: Electronic database search was performed in MEDLINE via PubMed, Embase via embase.com, and the Cochrane library website. Selection Criteria: The data were extracted according to two protocols based on Centre for Evidence-Based Medicine (CEBM) critical appraisal tools. Next, levels of evidence were categorized into three groups: low, medium, and high. Data Synthesis: Fifty-five publications were found through database search strategies. A total of nine publications were included in this review. Conclusion According to the available literature, 3D imaging modalities were more accurate and reliable as compared to 2D modalities. Cone beam computed tomography (CBCT) was considered the most reliable imaging tool for soft tissues.

Sign in / Sign up

Export Citation Format

Share Document