Added mass moment of inertia of centrifugal dredge pump impellers

In this study, a dynamic model of a single-cylinder four-stroke diesel engine has been created, and the crankshaft speed fluctuations have been simulated and validated. The dynamic model of the engine consists of the motion equations of the piston, conrod, and crankshaft. Conrod motion was modeled by two translational and one angular motion equations, by considering the kinetic energy resulted from the mass moment of inertia and conrod mass. Motion equations involve in-cylinder gas pressure forces, hydrodynamic and dry friction, mass inertia moments of moving parts, starter moment, and external load moment. The In-cylinder pressure profile used in the model was obtained experimentally to increase the accuracy of the model. Pressure profiles were expressed mathematically using the Fourier series. The motion equations were solved by using the Taylor series method. The solution of the mathematical model was performed by coding in the MATLAB interface. Cyclic speed fluctuations obtained from the model were compared with experimental results and found compitable. A validated model was used to analyze the effects of in-cylinder pressure, mass moment of inertia of crankshaft and connecting rod, friction, and piston mass. In experiments for 1500, 1800, 2400, and 2700 rpm engine speeds, crankshaft speed fluctuations were observed as 12.84%, 8.04%, 5.02%, and 4.44%, respectively. In simulations performed for the same speeds, crankshaft speed fluctuations were calculated as 10.45%, 7.56%, 4.49%, and 3.65%. Besides, it was observed that the speed fluctuations decreased as the average crankshaft speed value increased. In the simulation for 157.07, 188.49, 219.91, 251.32, and 282.74 rad/s crankshaft speeds, crankshaft speed fluctuations occurred at rates of 10.45%, 7.56%, 5.84%, 4.49%, and 3.65%, respectively. The effective engine power was achieved as 5.25 kW at an average crankshaft angular speed of 219.91 rad/s. The power of friction loss in the engine was determined as 0.68 kW.

Download Full-text

Pengaruh Variasi Radius-Dalam Rim Terhadap Pengurangan Massa dan Momen Inersia Massa Dengan Studi Kasus Benda Putar Berdiameter 10 cm

Jurnal Rekayasa Hijau ◽

10.26760/jrh.v1i1.1339 ◽

2018 ◽

Vol 1 (1) ◽

Author(s):

Eka Taufiq Firmansjah

Keyword(s):

Outer Radius ◽

Moment Of Inertia ◽

Mass Reduction ◽

Inner Radius ◽

Mass Moment ◽

Mass Moment Of Inertia ◽

Machine Elements ◽

The Moment ◽

The Masses

ABSTRAK Mesin terdiri dari sekumpulan elemen mesin yang diam dan bergerak. Elemen mesin yang bergerak dengan gerakan berputar disebut benda putar. Pada beberapa kasus seringkali diinginkan pengurangan massa dari benda putar tersebut untuk alasan ekonomis, biasanya untuk elemen mesin yag diproduksi massal. Namun pengurangan massa berakibat pada pengurangan momen inersia massa benda putar bersangkutan. Jika tuntutan perancangan tidak mempermasalahkan perubahan tersebut, maka pengurangan massa tidak menjadi masalah. Namun jika momen inersia massa tidak boleh terlalu rendah, maka harus dicari kompromi dimana pengurangan massa sebesar-besarnya namun penurunan momen inersia massa sekecil-kecilnya. Pada penelitian ini dilakukan studi kasus terhadap benda putar berjari- jari 10 cm jari-jari dalam hub 2 cm dan jari-jari luar hub 4 cm. Jumlah jari-jari ada 4 dengan lebar 1 cm dan tebal benda putar 0,5 cm. Variasi pengurangan massa dilakukan dengan memvariasikan jari-jari- dalam rim. Untuk tiap variasi, dilakukan perhitungan untuk mendapatkan jumlah massa yang dapat dikurangi dan momen inersia massa dari benda putar. Ternyata pada nilai jari-jari dalam tertentu, dapat diperoleh nilai kompromi dari permasalahan diatas. Kata kunci: benda putar, penghematan bahan, momen inersia massa. ABSTRACT Machine consists of a set of machine elements that still and moving. Machine elements that move in a circular motion called rotary object. In some cases it is often desirable reduction in the mass of the rotating object for economic reasons, usually for a mass production of machine elements. But the mass reduction results in a reduction in moment of inertia of the mass. If the demands of the design allow this decrease of moment of inertia, mass reduction is not a problem. But if the moment of inertia of the masses should not be too low, it must find a compromise in which a mass reduction profusely but the decrease in the mass moment of inertia of the smallest. In this research conducted a case study of rotating element radius of 10 cm, radius of the hub 2 cm and outer radius hub 4 cm. The number of spoke are 4 with a width of 1 cm and uniform thickness 0.5 cm all over rotating element. Variations mass reduction is done by varying the inner radius of the rim. For each variation, calculation is performed to obtain the amount of mass that can be reduced and the mass moment of inertia of the rotating object. It turned out that in the certain value of inner radius of the rim in particular, can compromise the values obtained from the above problem. Keywords: rotating element, reducing material, mass moment of inertia.

Download Full-text

An Analysis of the Simplified Two-Mass System of the Connecting Rod in Spark Ignition Engines

Design, Application, Performance and Emissions of Modern Internal Combustion Engine Systems and Components ◽

10.1115/icef2002-511 ◽

2002 ◽

Author(s):

Richard Stanley

Keyword(s):

Statistical Study ◽

Cylinder Liner ◽

Moment Of Inertia ◽

Average Error ◽

Spark Ignition Engines ◽

Connecting Rod ◽

Mass System ◽

Rolling Moment ◽

Mass Moment ◽

Mass Moment Of Inertia

Replacing the connecting rod with a lumped two-mass system causes an error, which influences the inertia rolling moment, the thrust force between the piston and the cylinder liner, and the loading on the main bearings. Dimensionless relationships have been found that relate the inertia error due to the connecting rod simplification (the inertia error) to the errors of the forces and moments that are created by it. Additionally, the results of a statistical study of 19 SI connecting rods indicate that the mass moment of inertia of the two mass system is −2.65% to 22% higher than that the experimentally measured moment of inertia of the connecting rod, with an average error value of 9.65%.

Download Full-text