scholarly journals Thermoelastic Martensitic Transformation and Shape Memory Effect in Sr2(Si, Ge)O4.

2001 ◽  
Vol 109 (1276) ◽  
pp. 1017-1022 ◽  
Author(s):  
Koichiro FUKUDA ◽  
Tetsuya FUKUDA ◽  
Akio SUZUKI ◽  
Akira YAMAGUCHI
2001 ◽  
Vol 291 (2-3) ◽  
pp. 175-183 ◽  
Author(s):  
A.A. Cherechukin ◽  
I.E. Dikshtein ◽  
D.I. Ermakov ◽  
A.V. Glebov ◽  
V.V. Koledov ◽  
...  

2013 ◽  
Vol 58 (6) ◽  
pp. 878-887 ◽  
Author(s):  
V. G. Pushin ◽  
N. N. Kuranova ◽  
E. B. Marchenkova ◽  
E. S. Belosludtseva ◽  
V. A. Kazantsev ◽  
...  

Author(s):  
А.Б. Тохметова ◽  
Н.Г. Ларченкова ◽  
Е.Ю. Панченко ◽  
Ю.И. Чумляков

The effects of stress-induced martensite aging (SIM-aging) along the [110]B2-direction on the thermoelastic martensitic transformation in Ni49Fe18Ga27Co6 single crystals were investigated. It was experimentally established that the effective regime of SIM-aging (at T = 423 K, 1 h under a compressive stress 450 MPa) results in a stabilization of stress-induced martensite and inducing the tensile two-way shape memory effect with reversible strain of +9.0 (± 0.3) % along the [001]B2-direction which is the perpendicular to the SIM-aging axis. Maximum work output of Wmax = 0.14 J/g (1125 kJ/m3) that can be realized using the two-way shape memory effect was obtained.


Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 943
Author(s):  
Yuriy I. Chumlyakov ◽  
Irina V. Kireeva ◽  
Zinaida V. Pobedennaya ◽  
Philipp Krooß ◽  
Thomas Niendorf

The two-step ageing of Fe-28Ni-17Co-11.5Al-2.5Nb (at. %) single crystals under and without stress, leads to the precipitation of the γ′- and β-phase particles. Research has shown that γ–α′ thermoelastic martensitic transformation (MT), with shape memory effect (SME) and superelasticity (SE), develops in the [001]-oriented crystals under tension. SE was observed within the range from the temperature of the start of MT upon cooling Ms, to the temperature of the end of the reverse MT upon heating Af, and at temperatures from Af to 323–373 K. It was found that at γ–α′ MT in the [001]-oriented crystals, with γ′- and β-phase particles, a high level of elastic energy, ΔGel, is generated, which significantly exceeds the energy dissipation, ΔGdis. As a result, the temperature of the start of the reverse MT, while heating As, became lower than the temperature Ms. The development of γ–α′ MT under stress occurs with high values of the transformation hardening coefficient, Θ = dσ/dε from 2 to 8 GPa and low values of mechanical Δσ and thermal ΔTh hysteresis. The reasons for an increase in ΔGel during the development of γ–α′ MT under stress are discussed.


2005 ◽  
Vol 96 (8) ◽  
pp. 843-846 ◽  
Author(s):  
Yunqing Ma ◽  
Lihong Xu ◽  
Yan Li ◽  
Chengbao Jiang ◽  
Huibin Xu ◽  
...  

2017 ◽  
Vol 62 (2) ◽  
pp. 1367-1370 ◽  
Author(s):  
Y.-W. Kim ◽  
T.W. Mukarati

AbstractNon-toxic Ti-Nb-Mo scaffolds were fabricated by sintering rapidly solidified alloy fibers for biomedical applications. Microstructure and martensitic transformation behaviors of the porous scaffolds were investigated by means of differential scanning calorimetric and X-ray diffraction. Theα″–βtransformation occurs in the as-solidified fiber and the sintered scaffolds. According to the compressive test of the sintered scaffolds with 75% porosity, they exhibit good superelasticity and strain recovery ascribed to the stress-induced martensitic transformation and the shape memory effect. Because of the high porosity of the scaffolds, an elastic modulus of 1.4 GPa, which matches well with that of cancellous bone, could be obtained. The austenite transformation finishing temperature of 77Ti-18Nb-5Mo alloy scaffolds is 5.1°C which is well below the human body temperature, and then all mechanical properties and shape memory effect of the porous 77Ti-18Nb-5Mo scaffolds are applicable for bon replacement implants.


Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 901
Author(s):  
Jie Chen ◽  
Yonghao Zhang ◽  
Jiqiang Ge ◽  
Huabei Peng ◽  
Shuke Huang ◽  
...  

To improve the shape memory effect (SME) of 304 austenitic steel effectively and efficiently, thermomechanical cycling, comprising deformation at room temperature and annealing, was applied. The influences of cycle number and annealing temperature on the SME and microstructures in 304 austenitic steel were investigated by light microscope (LM), X-ray diffraction (XRD), and transmission electron microscope (TEM). The shape recovery ratio was remarkably improved from 16% to 40% after two thermomechanical cycles. The optimum annealing temperature was 833 K in the process of thermomechanical cycling. The improved SME by thermomechanical cycling was mainly related to stress-induced ε martensite rather than stress-induced α’ martensite. The reason is that thermomechanical cycling can not only promote the occurrence of the stress-induced γ→ε martensitic transformation, but also suppress the subsequently stress-induced ε→α′ transformation.


Metals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1890
Author(s):  
Anton I. Tagiltsev ◽  
Elena Y. Panchenko ◽  
Ekaterina E. Timofeeva ◽  
Yuriy I. Chumlyakov ◽  
Ekaterina S. Marchenko ◽  
...  

This study investigated the effect of stress-induced martensite aging under tensile and compressive stresses on the functional and viscoelastic properties in Ni50.3Ti32.2Hf17.5 polycrystals containing dispersed H-phase particles up to 70 nm in size obtained by preliminary austenite aging at 873 K for 3 h. It was found that stress-induced martensite aging at 428 K for 12 h results in the appearance of a two-way shape memory effect of −0.5% in compression and +1.8% in tension. Moreover, a significant change in viscoelastic properties can be observed: an increase in internal friction (by 25%) and a change in elastic modulus in tensile samples. The increase in internal friction during martensitic transformation after stress-induced martensite aging is associated with the oriented growth of thermal-induced martensite. After stress-induced martensite aging, the elastic modulus of martensite (EM) increased by 8 GPa, and the elastic modulus of austenite (EA) decreased by 8 GPa. It was shown that stress-induced martensite aging strongly affects the functional and viscoelastic properties of material and can be used to control them.


Sign in / Sign up

Export Citation Format

Share Document