scholarly journals Effect Of Repeated Heat Pressing And Thermocycling On Micro Shear Bond Strength Of Polyetheretherketone (PEEK) To Resin Cement

2021 ◽  
Vol 67 (4) ◽  
pp. 3617-3627
Author(s):  
Ahmed Arafa ◽  
Marwa Emam
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Resin Cement

scholarly journals Effects of Universal Adhesive on Shear Bond Strength of Resin Cement to Zirconia Ceramic with Different Surface Treatments

2021 ◽  
Vol 2021 ◽  
pp. 1-6
Author(s):  
Zohreh Moradi ◽  
Farnoosh Akbari ◽  
Sara Valizadeh
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
In Vitro Study ◽  
Surface Treatments ◽  
Resin Cement ◽  
Zirconia Ceramic ◽  
Single Bond ◽  
Universal Adhesive

Aim. This study aimed to assess shear bond strength (SBS) of resin cement to zirconia ceramic with different surface treatments by using Single Bond Universal. Methods. In this in vitro study, 50 zirconia discs (2 × 6 mm) were divided into 5 groups of (I) sandblasting with silica-coated alumina (CoJet)  + silane + Single Bond 2, (II) sandblasting with CoJet + Single Bond Universal, (III) sandblasting with alumina + Single Bond Universal, (IV) sandblasting with alumina + Z-Prime Plus, and (V) Single Bond Universal with no surface treatment. Resin cement was applied in plastic tubes (3 × 5 mm2), and after 10,000 thermal cycles, the SBS was measured by a universal testing machine. The mode of failure was determined under a stereomicroscope at × 40 magnification. Data were analyzed using one-way ANOVA. Results. The maximum (6.56 ± 4.29 MPa) and minimum (1.94 ± 1.96 MPa) SBS values were noted in groups III and I, respectively. Group III had the highest frequency of mixed failure (60%). Group V had the maximum frequency of adhesive failure (100%). Conclusion. Single Bond Universal + sandblasting with alumina or silica-coated alumina particles is an acceptable method to provide a strong SBS between resin cement and zirconia.

Influence of laser structuring of PEEK, PEEK-GF30 and PEEK-CF30 surfaces on the shear bond strength to a resin cement

2018 ◽  
Vol 84 ◽  
pp. 225-234 ◽  
Author(s):  
Bruno Henriques ◽  
Douglas Fabris ◽  
Joana Mesquita-Guimarães ◽  
Anne C. Sousa ◽  
Nathalia Hammes ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Resin Cement ◽  
Laser Structuring

Shear bond strength of a self-adhesive resin cement to resin-coated dentin

2013 ◽  
Vol 51 (1) ◽  
pp. 27
Author(s):  
Jee-Youn Hong ◽  
Cheol-Woo Park ◽  
Jeong-Uk Heo ◽  
Min-Ki Bang ◽  
Jae-Jun Ryu
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Resin Cement ◽  
Adhesive Resin ◽  
Adhesive Resin Cement

scholarly journals Effect of Provisional Cements on Shear Bond Strength of Porcelain Laminate Veneers

2011 ◽  
Vol 05 (04) ◽  
pp. 373-379 ◽  
Author(s):  
Subutay Han Altintas ◽  
Onjen Tak ◽  
Asli Secilmis ◽  
Aslihan Usumez
Keyword(s):  
Bond Strength ◽  
Calcium Hydroxide ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
Acrylic Resin ◽  
Resin Cement ◽  
Control Group ◽  
Molar Teeth ◽  
Laminate Veneers ◽  
Selection Of

ABSTRACTObjectives: The purpose of this study was to evaluate the effect of three provisional cements and two cleaning techniques on the final bond strength of porcelain laminate veneers. Methods: The occlusal third of the crowns of forty molar teeth were sectioned and embedded in autopolymerizing acrylic resin. Dentin surfaces were polished and specimens were randomly divided into four groups (n=10). Provisional restorations were fabricated and two provisional restorations were cemented onto each tooth. Restorations were fixed with one of three different provisional cements: eugenol-free provisional cement (Cavex), calcium hydroxide (Dycal), and light-cured provisional cement (Tempond Clear). Provisional restorations were removed with either a dental explorer and air-water spray, or a cleaning bur (Opticlean). In the control group, provisional restorations were not used on the surfaces of specimens. IPS Empress 2 ceramic discs were luted with a dual-cured resin cement (Panavia F). Shear bond strength was measured using a universal testing machine. Data were statistically analyzed by ANOVA, Tukey’s HSD and Dunnett tests. Surfaces were examined by scanning electronic microscopy. Results: Significant differences were found between the control group and both the light-cured provisional cement groups and the eugenol-free provisional cement-cleaning bur group (P<.05). Groups that had received light-cured provisional cement showed the lowest bond strength values. Conclusions: Selection of the provisional cement is an important factor in the ultimate bond strength of the final restoration. Calcium hydroxide provisional cement and cleaning with a dental explorer are advisable. (Eur J Dent 2011;5:373-379)

scholarly journals Evaluation of the shear bond strength of resin cement to enamel after bleaching with Er: YAG and diode laser

2020 ◽  
Vol 29 ◽  
pp. 2633366X1989996
Author(s):  
Akin Ceyda ◽  
Sevimay Müjde ◽  
Ozyilmaz Ozgun Yusuf ◽  
Cokuk Neslihan
Keyword(s):  
Bond Strength ◽  
Diode Laser ◽  
Shear Bond Strength ◽  
Color Change ◽  
Resin Cement ◽  
Control Groups ◽  
Laser Applications ◽  
Yag Laser ◽  
Atomic Force ◽  
Electron Microscope Analysis

Objective: The shear bond strength (SBS) of composite resin cement and color change to enamel bleached with two different concentrations of hydrogen peroxide (HP) bleaching agents in combination with two different laser applications was evaluated. Materials and Methods: The Er: YAG laser ( λ = 2940 nm) and diode laser ( λ = 940 nm) were used with the bleaching agent consisting of 40% HP opalescence (Opalescence Xtra Boost, Ulgen, South Jordan, UT, USA) and 35% HP whiteness (Whiteness HP Blue, FGM Dental Products, Joinville, SC, Brazil). Seventy-two human extracted teeth were randomly divided into two groups: For the 40% HP treatment, 36 specimens were divided into three subgroups: (1) HP agent with no laser treatment, (2) HP agent treated with Er: YAG laser, and (3) HP agent treated with diode laser. The same protocol was performed for the 35% HP. The color change was analyzed using the Commission Internationale de l’ Eclairage (CIE) L* a* b* system and surface roughness was analyzed by an atomic force microscope. The specimens were bonded with resin cement and a shear bond test was performed at 0.5 mm/min. The failure surfaces were evaluated using scanning electron microscope analysis. Results: Δ E value of the 40% HP + Er: YAG group was significantly higher than the other groups while diode groups showed the lower SBS values than the control groups ( p < 0.05). Conclusions: The Er: YAG laser with 40% HP may be effective for the brighter teeth and the use of Er: YAG laser produced higher adhesion between enamel and resin cement than diode laser.

Sign in / Sign up

Export Citation Format

Share Document