Factors affecting population of filamentous bacteria in wastewater treatment plants with nutrients removal

2015 ◽  
Vol 73 (4) ◽  
pp. 790-797 ◽  
Author(s):  
Aleksandra Miłobędzka ◽  
Anna Witeska ◽  
Adam Muszyński
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Population Analysis ◽  
Principal Component ◽  
Volume Index ◽  
Filamentous Bacteria ◽  
Municipal Wastewater Treatment ◽  
Operational Parameters

Filamentous population in activated sludge and key operational parameters of full-scale municipal wastewater treatment plants (WWTPs) with bulking problems representative for Poland were investigated with quantitative fluorescence in situ hybridization. Statistical analyses revealed few relationships between operational parameters and biovolume of filamentous bacteria. Sludge age was not only positively correlated with abundance of Chloroflexi (parametric correlation and principal component analysis (PCA)), but also differentiated Microthrix population (analysis of variance (ANOVA)). Phylum Chloroflexi and pH presented a negative relation during the study (PCA). ANOVA showed that pH of influent and sludge volume index (SVI) differentiated abundance of types 0803 and 1851 of Chloroflexi and candidate division TM7. SVI increased along with higher abundance of Microthrix (positive parametric and non-parametric correlations and positive relation in PCA). Biovolumes of morphotypes 0803 and 1851 of Chloroflexi were differentiated by organic matter in influent, also by nutrients in the case of Chloroflexi type 1851. Chemical and biological oxygen demands (COD and BOD5, respectively) were negatively correlated with Microthrix. COD also differentiated the abundance of Haliscomenobacter hydrossis. Results of the study can be used to prevent WWTPs from excessive proliferation of filamentous bacteria and operational problems caused by them – bulking and foaming of activated sludge.

Population dynamics of filamentous bacteria identified in Polish full-scale wastewater treatment plants with nutrients removal

2014 ◽  
Vol 71 (5) ◽  
pp. 675-684 ◽  
Author(s):  
A. Miłobędzka ◽  
A. Muszyński
Keyword(s):  
Population Dynamics ◽  
Wastewater Treatment ◽  
Correlation Coefficient ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Full Scale ◽  
Volume Index ◽  
Nutrients Removal ◽  
Filamentous Bacteria ◽  
Municipal Wastewater Treatment

A comprehensive study of the identity and population dynamics of filamentous bacteria in five Polish full-scale municipal wastewater treatment plants (WWTPs) with nutrients removal had been carried out for 2 years. A quantitative culture-independent, molecular method – fluorescence in situ hybridization – was applied to evaluate the structure of different filamentous bacteria populations and their temporal variations. Activated sludge was examined for the abundance of 11 groups of filamentous bacteria. On average, filaments constituted 28% of all bacteria. All samples presented a low diversity of probe-defined filamentous bacteria, usually with significant domination of Chloroflexi (with distinction to types 1851, 0803 and others) and/or Microthrix (14% and 7% of EUBmix, respectively). Haliscomenobacter hydrossis, Mycolata, Skermania piniformis and TM7 were less abundant, whereas Curvibacter, Thiothrix/021N and family Gordonia have not been detected in any of the samples. The tested WWTPs showed similarity among species found and differences in their abundance. The composition of filamentous populations was rather stable in each plant and similar to those found in other European countries. Little differences between plants were shown by multivariate analysis of variance in terms of Chloroflexi and Microthrix. No significant general correlations have been found with Pearson product-moment correlation coefficient and Spearman's rank correlation coefficient. Medium correlation strength between the presence of different filaments was recorded only for Microthrix and Skermania piniformis. Deleterious effect on settling properties of sludge (measured as sludge volume index) was found only for abundance of Microthrix; a strong linear correlation was recorded between them. However, no other correlations with wastewater and operational data were revealed.

scholarly journals Influence of road salt thawing peaks on the inflow composition and activated sludge properties in municipal wastewater treatment

2021 ◽  
Author(s):  
J. Tauber ◽  
B. Flesch ◽  
V. Parravicini ◽  
K. Svardal ◽  
J. Krampe
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Road Salt ◽  
Volume Index ◽  
Municipal Wastewater Treatment ◽  
Floc Size ◽  
Floc Structure ◽  
Autotrophic Biomass

Abstract Operational data over 2 years from three large Austrian wastewater treatment plants (WWTPs) with design capacities of 4 million, 950,000 and 110,000 population equivalent (PE) were examined. Salt peaks, due to thawing road salt were detected and quantified by electrical conductivity, temperature and chloride measurement in the inflow of the WWTPs. Daily NaCl inflow loads up to 1,147 t/d and PE-specific loads of 0.26–0.5 kg NaCl/(PE · y) were found. To mimic the plants' behaviour in a controlled environment, NaCl was dosed into the inflow of a laboratory-scale activated sludge plant. The influence of salt peaks on important activated sludge parameters such as sludge volume index, settling velocity and floc size were investigated. Influent and effluent were sampled extensively to calculate removal rates. Respiration measurements were performed to quantify activated sludge activity. Particle size distributions of the activated sludge floc sizes were measured using laser diffraction particle sizing and showed a decrease of the floc size by approximately two-thirds. The floc structure was examined and documented using light microscopy. At salt concentrations below 1 g/L, increased respiration was found for autotrophic biomass, and between 1 and 3 g NaCl/L respiration was inhibited by up to 30%.

PARAMETERS FOR DYNAMIC SIMULATION OF W ASTEW ATER TREATMENT PLANTS WITH HIGH-RATE AND LOW-RATE ACTIVATED SLUDGE TANKS

1994 ◽  
Vol 30 (4) ◽  
pp. 211-214 ◽  
Author(s):  
E. Brands ◽  
M. Liebeskind ◽  
M. Dohmann
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Dynamic Simulation ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
High Rate ◽  
Yield Coefficient ◽  
Municipal Wastewater Treatment ◽  
Municipal Wastewater Treatment Plants ◽  
Low Rate

This study shows a comparison of important parameters for dynamic simulation concerning the highrate and low-rate activated sludge tanks of several municipal wastewater treatment plants. The parameters for the dynamic simulation of the single-stage process are quite well known, but parameters for the high-ratellow-rate activated sludge process are still missi ng, although a considerable number of wastewater treatment plants are designed and operated that way. At present any attempt to simulate their operation is restricted to the second stage due to missing data concerning growth rate, decay rate, yield coefficient and others.

Characterization of wastewater and activated sludge from European municipal wastewater treatment plants using the NUR test

1998 ◽  
Vol 38 (1) ◽  
pp. 303-310 ◽  
Author(s):  
V. Naidoo ◽  
V. Urbain ◽  
C. A. Buckley
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Municipal Wastewater Treatment ◽  
Batch Tests ◽  
Denitrification Kinetics ◽  
Municipal Wastewater Treatment Plants

Denitrification kinetics and wastewater characterization of eight different plants in Europe are discussed. Denitrification batch tests revealed three distinct rates except in the cases of Plaisir, Rostock and Orense where 4 rates were observed. The latter three plants revealed atypical rapid initial rates which were between 7 and 21 mgN/gVSS.h. All denitrification kinetics under non-limiting carbon conditions revealed fast first rates which ranged between 3.0 and 7.3 mgN/gVSS.h. Acetate was used to simulate denitrification kinetics with readily biodegradable COD present. Two subsequent rates were observed. Rates 2 and 3 ranged between 2 and 3 mgN/gVSS.h, and 1 and 2 mgN/gVSS.h, respectively. The RBCOD fraction varied between 10 and 19%, except for one of the plants where the value determined was 7%.

scholarly journals Improving and upgrading an existing activated sludge with a compact MBBR – disc filters parallel line for municipal wastewater treatment in touristic alpine areas

2020 ◽  
Vol 15 (2) ◽  
pp. 515-527
Author(s):  
L. Desa ◽  
P. Kängsepp ◽  
L. Quadri ◽  
G. Bellotti ◽  
K. Sørensen ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Oxygen Demand ◽  
Parallel Line ◽  
Ammonium Nitrogen ◽  
Biofilm Reactor ◽  
Municipal Wastewater Treatment ◽  
Yearly Average

Abstract Many wastewater treatment plants (WWTP) in touristic areas struggle to achieve the effluent requirements due to seasonal variations in population. In alpine areas, the climate also determines a low wastewater temperature, which implies long sludge retention time (SRT) needed for the growth of nitrifying biomass in conventional activated sludge (CAS). Moreover, combined sewers generate high flow and dilution. The present study shows how the treatment efficiency of an existing CAS plant with tertiary treatment can be upgraded by adding a compact line in parallel, consisting of a Moving Bed Biofilm Reactor (MBBR)-coagulation-flocculation-disc filtration. This allows the treatment of influent variations in the MBBR and a constant flow supply to the activated sludge. The performance of the new 2-step process was comparable to that of the improved existing one. Regardless significant variations in flow (10,000–25,000 m3/d) and total suspended solids (TSS) (50–300 mg/L after primary treatment) the effluent quality fulfilled the discharge requirements. Based on yearly average effluent data, TSS were 11 mg/L, chemical oxygen demand (COD) 27 mg/L and total phosphorus (TP) 0.8 mg/L. After the upgrade, ammonium nitrogen (NH4-N) dropped from 4.9 mg/L to 1.3 mg/L and the chemical consumption for phosphorus removal was reduced.

scholarly journals LCA of a Membrane Bioreactor Compared to Activated Sludge System for Municipal Wastewater Treatment

Membranes ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 421
Author(s):  
Dimitra C. Banti ◽  
Michail Tsangas ◽  
Petros Samaras ◽  
Antonis Zorpas
Keyword(s):  
Wastewater Treatment ◽  
Life Cycle ◽  
Activated Sludge ◽  
Membrane Bioreactor ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Treatment Plant ◽  
Real Data ◽  
Municipal Wastewater Treatment ◽  
Conventional Activated Sludge

Membrane bioreactor (MBR) systems are connected to several advantages compared to the conventional activated sludge (CAS) units. This work aims to the examination of the life cycle environmental impact of an MBR against a CAS unit when treating municipal wastewater with similar influent loading (BOD = 400 mg/L) and giving similar high-quality effluent (BOD < 5 mg/L). The MBR unit contained a denitrification, an aeration and a membrane tank, whereas the CAS unit included an equalization, a denitrification, a nitrification, a sedimentation, a mixing, a flocculation tank and a drum filter. Several impact categories factors were calculated by implementing the Life Cycle Assessment (LCA) methodology, including acidification potential, eutrophication potential, global warming potential (GWP), ozone depletion potential and photochemical ozone creation potential of the plants throughout their life cycle. Real data from two wastewater treatment plants were used. The research focused on two parameters which constitute the main differences between the two treatment plants: The excess sludge removal life cycle contribution—where GWPMBR = 0.50 kg CO2-eq*FU−1 and GWPCAS = 2.67 kg CO2-eq*FU−1 without sludge removal—and the wastewater treatment plant life cycle contribution—where GWPMBR = 0.002 kg CO2-eq*FU−1 and GWPCAS = 0.14 kg CO2-eq*FU−1 without land area contribution. Finally, in all the examined cases the environmental superiority of the MBR process was found.

scholarly journals Initiating Biodegradation of Polyvinylpyrrolidone in an Aqueous Aerobic Environment: Technical Note / Zainicjowanie Biodegradacji Poliwinylopirolidonu W Środowisku Wodno-Tlenowym: Notatki Techniczne

2013 ◽  
Vol 20 (1) ◽  
pp. 199-208 ◽  
Author(s):  
Marketa Julinova ◽  
Jan Kupec ◽  
Roman Slavik ◽  
Maria Vaskova
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Waste Treatment ◽  
Wastewater Treatment Plants ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Technical Note ◽  
Aerobic Biodegradation ◽  
Municipal Wastewater Treatment

Abstract A synthetic polymer, polyvinylpyrrolidone (PVP - E 1201) primarily finds applications in the pharmaceutical and food industries due to its resistance and zero toxicity to organisms. After ingestion, the substance passes through the organism unchanged. Consequently, it enters the systems of municipal wastewater treatment plants (WWTP) without decomposing biologically during the waste treatment process, nor does it attach (through sorption) to particles of activated sludge to any significant extent, therefore, it passes through the system of a WWTP, which may cause the substance to accumulate in the natural environment. For this reason the paper investigates the potential to initiate aerobic biodegradation of PVP in the presence of activated sludge from a municipal wastewater treatment plant. The following agents were selected as the initiators of the biodegradation process - co-substrates: acrylamide, N-acethylphenylalanine and 1-methyl-2-pyrrolidone, a substance with a similar structure to PVP monomer. The biodegradability of PVP in the presence of co-substrates was evaluated on the basis of biological oxygen demand (BOD) as determined via a MicroOxymax O2/CO2/CH4 respirometer. The total substrate concentration in the suspension equaled 400 mg·dm-3, with the ratio between PVP and the cosubstrate being 1:1, while the concentration of the dry activated sludge was 500 mg·dm-3. Even though there was no occurrence of a significant increase in the biodegradation of PVP alone in the presence of a co-substrate, acrylamide appeared to be the most effective type of co-substrate. Nevertheless, a recorded decrease in the slope of biodegradation curves over time may indicate that a process of primary decomposition was underway, which involves the production of metabolites that inhibit activated sludge microorganisms. The resulting products are not identified at this stage of experimentation.

scholarly journals Casimicrobium huifangae gen. nov., sp. nov., a Ubiquitous “Most-Wanted” Core Bacterial Taxon from Municipal Wastewater Treatment Plants

2019 ◽  
Vol 86 (4) ◽  
Author(s):  
Yang Song ◽  
Cheng-Ying Jiang ◽  
Zong-Lin Liang ◽  
Bao-Jun Wang ◽  
Yong Jiang ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Carbon Sources ◽  
Short Chain Fatty Acids ◽  
Municipal Wastewater Treatment ◽  
Content Type ◽  
Bacterial Taxon ◽  
Municipal Wastewater Treatment Plants

ABSTRACT Microorganisms in wastewater treatment plants (WWTPs) play a key role in the removal of pollutants from municipal and industrial wastewaters. A recent study estimated that activated sludge from global municipal WWTPs harbors 1 × 109 to 2 × 109 microbial species, the majority of which have not yet been cultivated, and 28 core taxa were identified as “most-wanted” ones (L. Wu, D. Ning, B. Zhang, Y. Li, et al., Nat Microbiol 4:1183–1195, 2019, https://doi.org/10.1038/s41564-019-0426-5). Cultivation and characterization of the “most-wanted” core bacteria are critical to understand their genetic, physiological, phylogenetic, and ecological traits, as well as to improve the performance of WWTPs. In this study, we isolated a bacterial strain, designated SJ-1, that represents a novel cluster within Betaproteobacteria and corresponds to OTU_16 within the 28 core taxa in the “most-wanted” list. Strain SJ-1 was identified and nominated as Casimicrobium huifangae gen. nov., sp. nov., of a novel family, Casimicrobiaceae. C. huifangae is ubiquitously distributed and is metabolically versatile. In addition to mineralizing various carbon sources (including carbohydrates, aromatic compounds, and short-chain fatty acids), C. huifangae is capable of nitrate reduction and phosphorus accumulation. The population of C. huifangae accounted for more than 1% of the bacterial population of the activated sludge microbiome from the Qinghe WWTP, which showed seasonal dynamic changes. Cooccurrence analysis suggested that C. huifangae was an important module hub in the bacterial network of Qinghe WWTP. IMPORTANCE The activated sludge process is the most widely applied biotechnology and is one of the best ecosystems to address microbial ecological principles. Yet, the cultivation of core bacteria and the exploration of their physiology and ecology are limited. In this study, the core and novel bacterial taxon C. huifangae was cultivated and characterized. This study revealed that C. huifangae functioned as an important module hub in the activated sludge microbiome, and it potentially plays an important role in municipal wastewater treatment plants.

Sign in / Sign up

Export Citation Format

Share Document