scholarly journals Эволюция структуры и свойств сплава Ni-=SUB=-47-=/SUB=-Mn-=SUB=-42-=/SUB=-In-=SUB=-11-=/SUB=- после пластической деформации

2019 ◽  
Vol 61 (11) ◽  
pp. 2204
Author(s):  
Ю.В. Калетина ◽  
Е.Д. Грешнова ◽  
А.Ю. Калетин
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
High Pressure ◽  
Magnetic Susceptibility ◽  
Severe Plastic Deformation ◽  
Room Temperature ◽  
Nanocrystalline Structure ◽  
Physical And Mechanical Properties ◽  
Coarse Grain ◽  
Deformation By Rolling

AbstractResults of the study of the effect of various types of plastic deformation on microstructural features and change in physical and mechanical properties of the nonstoichiometric Heusler alloy Ni_47Mn_42In_11 are shown. It was demonstrated that the deformation by rolling and upsetting leads to an increase in the microhardness and to an embrittlement of the investigated alloy. Severe plastic deformation by torsion under high pressure of 8 GPa at room temperature was found to strongly refine initially coarse grain and to contribute to the formation of a nanocrystalline structure with grain fragments up to 10 nm. In this case, the fraction of viscous constituent on the fracture and the microhardness increased, while the magnetic susceptibility decreased.

Superplasticity of Aerospace 7075 (Al-Zn-Mg-Cu) Aluminium Alloy Obtained by Severe Plastic Deformation

2018 ◽  
Vol 385 ◽  
pp. 39-44 ◽  
Author(s):  
Fernando Carreño ◽  
Oscar A. Ruano
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Aluminium Alloy ◽  
Room Temperature ◽  
Grain Boundary Sliding ◽  
Strain Rates ◽  
Aerospace Applications ◽  
Boundary Sliding ◽  
Processing Stress

The 7075 (Al-Zn-Mg-Cu) aluminium alloy is the reference alloy for aerospace applications due to its specific mechanical properties at room temperature, showing excellent tensile strength and sufficient ductility. Formability at high temperature can be improved by obtaining superplasticity as a result of fine, equiaxed and highly misoriented grains prone to deform by grain boundary sliding (GBS). Different severe plastic deformation (SPD) processing routes such as ECAP, ARB, HPT and FSP have been considered and their effect on mechanical properties, especially at intermediate to high temperatures, are studied. Refined grains as fine as 100 nm and average misorientations as high as 39o allow attainment of high strain rate superplasticity (HSRSP) at lower than usual temperatures (250-300oC). It is shown that increasing misorientations are obtained with increasing applied strain, and increasing grain refinement is obtained with increasing processing stress. Thus, increasing superplastic strains at higher strain rates, lower stresses and lower temperatures are obtained with increasing processing strain and, specially, processing stress.

Current States and Development of Research on Redissolution and Reprecipitation of Nanoprecipitated Phases in Al–Cu Alloys

2019 ◽  
Vol 11 (11) ◽  
pp. 1489-1501
Author(s):  
Wenjing He ◽  
Caihe Fan ◽  
Shu Wang ◽  
Junhong Wang ◽  
Su Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Room Temperature ◽  
Supersaturated Solid Solution ◽  
Aluminum Matrix ◽  
Aging Treatment ◽  
Cu Alloys ◽  
The Reformation

The evolution of nanoprecipitated phases in Al–Cu alloys under severe plastic deformation (SPD) is summarized in this study. SPD at room temperature induces the precipitation of Al–Cu alloys to dissolve, leading to the reformation of supersaturated solid solution in the aluminum matrix. In the process of SPD or aging treatment after the SPD, the reprecipitated phases are precipitated from the aluminum matrix and the mechanical properties of the alloys are remarkably improved. The mechanism and system of the redissolution of the precipitation phases and the effects of redissolution and reprecipitation on the microstructure and properties of Al–Cu alloys are comprehensively analyzed. The development and future of redissolution and reprecipitation of nanoprecipitated phases in Al–Cu alloys are also described.

Mechanical Properties of Ultrafine-Grained Al-Mg Alloy Produced by Severe Plastic Deformation

2017 ◽  
Vol 743 ◽  
pp. 203-206 ◽  
Author(s):  
Alexander A. Kozulin ◽  
Vladimir A. Krasnoveikin ◽  
Vladimir A. Skripnyak ◽  
Evgeny N. Moskvichev ◽  
Valery E. Rubtsov
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
High Efficiency ◽  
Physical And Mechanical Properties ◽  
Treatment Method ◽  
Mg Alloy ◽  
Complex Investigation ◽  
Angular Pressing ◽  
Ultrafine Grained

This study examines the effect of severe plastic deformation on the physical and mechanical properties of a light structural Al-Mg alloy. Severe plastic deformation has been performed by equal channel angular pressing through a die with an angle of 90° between the channels to produce ultrafine-grained structure in specimens of studied alloy. A complex investigation of the physical and mechanical properties of the processed alloy has been carried out to examine the microstructure and texture, and to measure microhardness, yield stress and ultimate tensile strength. The obtained results demonstrate high efficiency of the chosen treatment method and mode of producing a light ultrafine-grained alloy.

scholarly journals Influence of special features of the gradient structure formation during severe plastic deformation of alloys with different types of a crystalline lattice

2019 ◽  
Vol 17 (1) ◽  
pp. 64-75 ◽  
Author(s):  
Georgy I. Raab ◽  
Ilyas S. Kodirov ◽  
Gennady N. Aleshin ◽  
Arseniy G. Raab ◽  
Nikolai K. Tsenev
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
Structure Formation ◽  
High Pressure Torsion ◽  
Crystalline Lattice ◽  
Gradient Structure ◽  
Temperature Range ◽  
Deformation Treatment

Problem Statement (Relevance): The paper describes some features and prospective benefits of deformation by methods of drawing with shear (SD) and high pressure torsion (HPT) in a temperature range of dynamic strain aging (DSA) effect, which allow receiving a high complex of physical and mechanical properties. Objectives: The study aims to investigate and analyze features of the structure formation with the combined application of severe plastic deformation (SPD) and the DSA effect during deformation by drawing with shear and high pressure torsion, to establish patterns of the gradient structure formation. Methods Applied: 1. Computer simulation in Deform 3D software to investigate the stress-strain state on materials with various types of a crystalline lattice: copper grade M1 (FCC), Steel 10 (BCC) and titanium VT1-0 (HCP) and a further comparison with experimental results. 2. Microhardness measurement 3. Scanning and transmission electron microscopy. Originality: This research resulted in investigation of the combined effect of the DSA effect and SPD on the gradient structure formation and mechanical properties of metals with various crystalline lattices. Findings: the paper presents the results of the study of the structure formation during non-monotonous plastic deformation of the alloys (steel 10, copper and titanium) with various crystalline lattice types by SD, as well as ECAP and HPT of low-carbon steel in the temperature range of the DSA effect. Deformation mechanisms and features of the deformation behavior on a mesoscopic scale under various deformation treatment modes are analyzed. The temperature range of the DSA effect in steel 10 under ECAP and the fact of the gradient structure formation under HPT are established. Practical Relevance: The study helped to obtain data that can be used to choose the optimal deformation treatment mode with the DSA effect.

Recrystallization and Grain Growth in Ultra Fine Grained Materials Produced by High Pressure Torsion

2012 ◽  
Vol 715-716 ◽  
pp. 373-373
Author(s):  
Anahita Khorashadizadeh ◽  
Myrjam Winning ◽  
Stefan Zaefferer ◽  
Dierk Raabe
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
Grain Growth ◽  
High Pressure Torsion ◽  
Fine Grained ◽  
Fine Grained Material

Investigations of the microstructure of materials processed via severe plastic deformation methods such as high pressure torsion (HPT) and their recrystallization behaviour is of great interest as they are capable of producing ultra fine grained material (UFD) with good mechanical properties.

Submicrocrystalline Austenitic Stainless Steel Processed by Cold or Warm High Pressure Torsion

2016 ◽  
Vol 838-839 ◽  
pp. 398-403 ◽  
Author(s):  
Marina Tikhonova ◽  
Nariman Enikeev ◽  
Ruslan Z. Valiev ◽  
Andrey Belyakov ◽  
Rustam Kaibyshev
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Severe Plastic Deformation ◽  
Room Temperature ◽  
High Pressure Torsion ◽  
Submicrocrystalline Structure ◽  
Ultrafine Grained ◽  
Different Temperatures

The formation of submicrocrystalline structure during severe plastic deformation and its effect on mechanical properties of an S304H austenitic stainless steel with chemical composition of Fe – 0.1C – 0.12N – 0.1Si – 0.95Mn – 18.4Cr – 7.85Ni – 3.2Cu – 0.5Nb – 0.01P – 0.006S (all in mass%) were studied. The severe plastic deformation was carried out by high pressure torsion (HPT) at two different temperatures, i.e., room temperature or 400°C. HPT at room temperature or 400°C led to the formation of a fully austenitic submicrocrystalline structure. The grain size and strength of the steels with ultrafine-grained structures produced by cold or warm HPT were almost the same. The ultimate tensile strengths were 1950 MPa and 1828 MPa after HPT at room temperature and 400°C, respectively.

Sign in / Sign up

Export Citation Format

Share Document