Geometry Effects in Eulerian/Granular Simulation of a Turbulent FCC Riser with a (kg-?g)-KTGF Model

2010 ◽  
Vol 8 (1) ◽  
Author(s):  
Hamid Reza Nazif ◽  
Hassan Basirat Tabrizi ◽  
Farhad A Farhadpour
Keyword(s):  
Cross Section ◽  
Large Scale ◽  
Rectangular Cross Section ◽  
Three Dimensional ◽  
Circular Cross Section ◽  
Good Prediction ◽  
Model Predictions ◽  
Secondary Circulations ◽  
Sharp Corners ◽  
Granular Simulation

Three-dimensional, transient turbulent particulate flow in an FCC riser is modeled using an Eulerian/Granular approach. The turbulence in the gas phase is described by a modified realizable (kg-?g) closure model and the kinetic theory of granular flow (KTGF) is employed for the particulate phase. Separate simulations are conducted for a rectangular and a cylindrical riser with similar dimensions. The model predictions are validated against experimental data of Sommerfeld et al (2002) and also compared with the previously reported LES-KTGF simulations of Hansen et al (2003) for the rectangular riser. The (kg-?g)-KTGF model does not perform as well as the LES-KTGF model for the riser with a rectangular cross section. This is because, unlike the more elaborate LES-KTGF model, the simpler (kg-?g)-KTGF model cannot capture the large scale secondary circulations induced by anisotropic turbulence at the corners of the rectangular riser. In the cylindrical geometry, however, the (kg-?g)-KTGF model gives good prediction of the data and is a viable alternative to the more complex LES-KTGF model. This is not surprising as the circulations in the riser with a circular cross section are due to the curvature of the walls and not due to the presence of sharp corners.

Effects of Volute Curvature on Performance of a Low Specific-Speed Centrifugal Pump at Design and Off-Design Conditions

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Hamed Alemi ◽  
Seyyed Ahmad Nourbakhsh ◽  
Mehrdad Raisee ◽  
Amir Farhad Najafi
Keyword(s):  
Centrifugal Pump ◽  
Cross Section ◽  
Constant Velocity ◽  
Rectangular Cross Section ◽  
Three Dimensional ◽  
Circular Cross Section ◽  
Turbulence Models ◽  
Radial Force ◽  
Low Specific Speed ◽  
Specific Speed

The effects of the volute geometry on the head, efficiency, and radial force of a low specific-speed centrifugal pump were investigated focusing on off-design conditions. This paper is divided into three parts. In the first part, the three-dimensional flow inside the pump with rectangular volute was simulated using three well-known turbulence models. Simulation results were compared with the available experimental data, and an acceptable agreement was obtained. In the second part, two volute design methods, namely, the constant velocity and the constant angular momentum were investigated. Obtained results showed that in general the constant velocity method gives more satisfactory performance. In the third part, three volutes with different cross section and diffuser shape were designed. In general, it was found that circular cross section volute with radial diffuser provides higher head and efficiency. Moreover, the minimum radial force occurs at higher flowrate in circular volute geometry comparing to rectangular cross section volute.

SAF file: It's really three dimensional file

2018 ◽  
Vol 14 (1) ◽  
pp. 1
Author(s):  
Prof. Dr. Jamal Aziz Mehdi
Keyword(s):  
Cross Section ◽  
Root Canal ◽  
Three Dimensional ◽  
Circular Cross Section ◽  
Circular Motion ◽  
Root Canal Treatment ◽  
Metal Core ◽  
Rotating Blade

The biological objectives of root canal treatment have not changed over the recentdecades, but the methods to attain these goals have been greatly modified. Theintroduction of NiTi rotary files represents a major leap in the development ofendodontic instruments, with a wide variety of sophisticated instruments presentlyavailable (1, 2).Whatever their modification or improvement, all of these instruments have onething in common: they consist of a metal core with some type of rotating blade thatmachines the canal with a circular motion using flutes to carry the dentin chips anddebris coronally. Consequently, all rotary NiTi files will machine the root canal to acylindrical bore with a circular cross-section if the clinician applies them in a strictboring manner

On the Flexural-Torsional Behavior of a Straight Elastic Beam Subject to Terminal Moments

1993 ◽  
Vol 60 (2) ◽  
pp. 498-505 ◽  
Author(s):  
Z. Tan ◽  
J. A. Witz
Keyword(s):  
Coordinate System ◽  
Cross Section ◽  
Equilibrium Equation ◽  
Three Dimensional ◽  
Circular Cross Section ◽  
Elastic Beam ◽  
Cartesian Coordinate System ◽  
Kinematic Constraints ◽  
Torsional Behavior ◽  
Cartesian Coordinate

This paper discusses the large-displacement flexural-torsional behavior of a straight elastic beam with uniform circular cross-section subject to arbitrary terminal bending and twisting moments. The beam is assumed to be free from any kinematic constraints at both ends. The equilibrium equation is solved analytically with the full expression for curvature to obtain the deformed configuration in a three-dimensional Cartesian coordinate system. The results show the influence of the terminal moments on the beam’s deflected configuration.

Analysis of Twisting Stiffness for a Multifiber Composite Layer

1974 ◽  
Vol 41 (3) ◽  
pp. 658-662 ◽  
Author(s):  
C. W. Bert ◽  
S. Chang
Keyword(s):  
Cross Section ◽  
Least Squares Method ◽  
Rectangular Cross Section ◽  
Torsional Rigidity ◽  
Composite Layer ◽  
Circular Cross Section ◽  
Relaxation Method ◽  
Fiber Composites ◽  
Numerical Results ◽  
Torsion Problem

The twisting stiffness of a rectangular cross section consisting of a single row of solid circular cross-section fibers embedded in a matrix is analyzed. The problem is formulated as a Dirichlet torsion problem of a multielement region and solved by the boundary-point least-squares method. Numerical results for a single-fiber square cross section compare favorably with previous relaxation-method results. New numerical results for three and five-fiber composites suggest that the torsional rigidity of a multifiber composite can be approximated from the torsional rigidities of single and three-fiber models.

The Uniform Flexure of an Incomplete Tore

1949 ◽  
Vol 2 (4) ◽  
pp. 469
Author(s):  
W Freiberger ◽  
RCT Smith
Keyword(s):  
General Solution ◽  
Cross Section ◽  
Harmonic Functions ◽  
Rectangular Cross Section ◽  
Three Dimensional ◽  
Elasticity Problems ◽  
Three Dimensional Elasticity ◽  
Derivatives Of ◽  
Special Case

In this paper we discuss the flexure of an incomplete tore in the plane of its circular centre-line. We reduce the problem to the determination of two harmonic functions, subject to boundary conditions on the surface of the tore which involve the first two derivatives of the functions. We point out the relation of this solution to the general solution of three-dimensional elasticity problems. The special case of a narrow rectangular cross-section is solved exactly in Appendix II.

Bending Vibrations of Variable Section Beams

1956 ◽  
Vol 23 (1) ◽  
pp. 103-108
Author(s):  
E. T. Cranch ◽  
Alfred A. Adler
Keyword(s):  
Cross Section ◽  
Rectangular Cross Section ◽  
Circular Cross Section ◽  
Beam Theory ◽  
Cantilever Beams ◽  
Constant Depth ◽  
Bending Vibrations ◽  
Variable Section

Abstract Using simple beam theory, solutions are given for the vibration of beams having rectangular cross section with (a) linear depth and any power width variation, (b) quadratic depth and any power width variation, (c) cubic depth and any power width variation, and (d) constant depth and exponential width variation. Beams of elliptical and circular cross section are also investigated. Several cases of cantilever beams are given in detail. The vibration of compound beams is investigated. Several cases of free double wedges with various width variations are discussed.

Shear-Driven Flow in a Toroid of Square Cross Section

2003 ◽  
Vol 125 (1) ◽  
pp. 130-137 ◽  
Author(s):  
J. A. C. Humphrey ◽  
J. Cushner ◽  
M. Al-Shannag ◽  
J. Herrero ◽  
F. Giralt
Keyword(s):  
Cross Section ◽  
Finite Length ◽  
Rectangular Cross Section ◽  
Three Dimensional ◽  
Transition To Turbulence ◽  
Radius Of Curvature ◽  
Infinite Length ◽  
Core Flow ◽  
Reynolds Number Flow ◽  
End Wall

The two-dimensional wall-driven flow in a plane rectangular enclosure and the three-dimensional wall-driven flow in a parallelepiped of infinite length are limiting cases of the more general shear-driven flow that can be realized experimentally and modeled numerically in a toroid of rectangular cross section. Present visualization observations and numerical calculations of the shear-driven flow in a toroid of square cross section of characteristic side length D and radius of curvature Rc reveal many of the features displayed by sheared fluids in plane enclosures and in parallelepipeds of infinite as well as finite length. These include: the recirculating core flow and its associated counterrotating corner eddies; above a critical value of the Reynolds (or corresponding Goertler) number, the appearance of Goertler vortices aligned with the recirculating core flow; at higher values of the Reynolds number, flow unsteadiness, and vortex meandering as precursors to more disorganized forms of motion and eventual transition to turbulence. Present calculations also show that, for any fixed location in a toroid, the Goertler vortex passing through that location can alternate its sense of rotation periodically as a function of time, and that this alternation in sign of rotation occurs simultaneously for all the vortices in a toroid. This phenomenon has not been previously reported and, apparently, has not been observed for the wall-driven flow in a finite-length parallelepiped where the sense of rotation of the Goertler vortices is determined and stabilized by the end wall vortices. Unlike the wall-driven flow in a finite-length parallelepiped, the shear-driven flow in a toroid is devoid of contaminating end wall effects. For this reason, and because the toroid geometry allows a continuous variation of the curvature parameter, δ=D/Rc, this flow configuration represents a more general paradigm for fluid mechanics research.

scholarly journals Particle separation of a modified feed nozzle hydrocyclone under different operating parameters

2021 ◽  
Vol 11 (5) ◽  
pp. 159-170
Author(s):  
Zsolt Hegyes ◽  
Máté Petrik ◽  
L. Gábor Szepesi
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Rectangular Cross Section ◽  
Circular Cross Section ◽  
Particle Separation ◽  
Baffle Plate ◽  
Important Data ◽  
Preliminary Research ◽  
All Speeds ◽  
Plate Solution

During the operation of the hydrocyclone the cut size diameter is the most important data. This is connected to feed rate, which is closely related to the feed cross section. Preliminary research has revealed that square cross-section is more effective than circular cross-section. The research compared 2 types of feed cross sections at 5 different feed rates. One is a standard rectangular cross-section and the other is a square cross-section that narrows with a baffle plate. Preliminary calculations for cut size diameter have shown that better particle separation at all speeds can be achieved with the baffle plate solution. In both types, the increased velocity created decreased cut size diameter. During the simulation, the baffle plate did not cause any abnormalities in the internal pressure and velocity distributions. The simulation revealed that the particles did not behave as previously calculated.

Heat Transfer for Laminar Flow in Spiral Ducts of Rectangular Cross Section

2005 ◽  
Vol 127 (3) ◽  
pp. 352-356 ◽  
Author(s):  
Michael W. Egner ◽  
Louis C. Burmeister
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Laminar Flow ◽  
Cross Section ◽  
Rectangular Cross Section ◽  
Three Dimensional ◽  
Radius Of Curvature ◽  
Dean Number ◽  
Aspect Ratios ◽  
Small Pitch

Laminar flow and heat transfer in three-dimensional spiral ducts of rectangular cross section with aspect ratios of 1, 4, and 8 were determined by making use of the FLUENT computational fluid dynamics program. The peripherally averaged Nusselt number is presented as a function of distance from the inlet and of the Dean number. Fully developed values of the Nusselt number for a constant-radius-of-curvature duct, either toroidal or helical with small pitch, can be used to predict those quantities for the spiral duct in postentry regions. These results are applicable to spiral-plate heat exchangers.

Sign in / Sign up

Export Citation Format

Share Document