scholarly journals Comparison of Response Spectrum Method and Seismic Coefficient Method for G+10 Building Resting on Sloping Ground

Author(s):  
Sufyan Ansari
2012 ◽  
Vol 226-228 ◽  
pp. 70-75
Author(s):  
Yun Xiang Lu ◽  
Ze Fang Lou ◽  
Bo Liu ◽  
Xiao Cheng Pan

This paper puts forward pseudo-response spectrum method for calculating the dynamic response of structure caused by harmonic load on the floor, and proposes to use frequency ratio as a new modal truncation index. Combined with engineering practice, the analysis results of pseudo-response spectrum method were compared with the results of existing dynamic coefficient method and elastic time-history method. The contrast results show that dynamic coefficient method due to lacking of considering dynamic properties enough was not able to meet the real response and could not evaluate the comfort of the vibration. The results of pseudo-response spectrum method with suitable mode combination method have the same law of the maximum enveloping value as elastic time-history method. This proved that pseudo-response spectrum method is reasonable, safe and economical, which can provide the basis for engineering design.


2021 ◽  
pp. 107754632110075
Author(s):  
Junling Chen ◽  
Jinwei Li ◽  
Dawei Wang ◽  
Youquan Feng

The steel–concrete hybrid wind turbine tower is characterized by the concrete tubular segment at the lower part and the traditional steel tubular segment at the upper part. Because of the great change of mass and stiffness along the height of the tower at the connection of steel segment and concrete segment, its dynamic responses under seismic ground motions are significantly different from those of the traditional steel tubular wind turbine tower. Two detailed finite element models of a full steel tubular tower and a steel–concrete hybrid tower for 2.0 MW wind turbine built in the same wind farm are, respectively, developed by using the finite element software ABAQUS. The response spectrum method is applied to analyze the seismic action effects of these two towers under three different ground types. Three groups of ground motions corresponding to three ground types are used to analyze the dynamic response of the steel–concrete hybrid tower by the nonlinear time history method. The numerical results show that the seismic action effect by the response spectrum method is lower than those by the nonlinear time history method. And then it can be concluded that the response spectrum method is not suitable for calculating the seismic action effects of the steel–concrete hybrid tower directly and the time history analyses should be a necessary supplement for its seismic design. The first three modes have obvious contributions on the dynamic response of the steel–concrete hybrid tower.


2011 ◽  
Vol 110-116 ◽  
pp. 5240-5248
Author(s):  
Sujay Shelke ◽  
H.V. Vankudre ◽  
Vinay Patil

Typical seismic analysis using response spectrum method involves several steps from the initial step of extracting the modes. At the initial stage Eigen values are extracted corresponding to the modes of vibration. These give us Eigen vectors which are a series of relative displacement shapes; however these do not correspond to real displacements or stresses. Participation factors asses these Eigen vectors and grades them according to contribution they will have to the overall solution. Based on the spectral seismic acceleration, participation factor is used to calculate the mode coefficient, which is more of a scaling factor to give physical meaning to the values. Once the modes are extracted, the key issue is of combining these modes to obtain the seismic response. The modes cannot be added algebraically in reality as all the modes do not occur at the same time. Hence we employ methods which can add the modes in a more realistic manner. The objective of this paper is to do a comparative study of various mode combination methods with a focus on tank structures and study the effect of various geometrical parameters on the combination methods


Author(s):  
Xuan Huang ◽  
Pingchuan Shen ◽  
Shuai Liu ◽  
Jian Liu ◽  
Xiaozhou Jiang ◽  
...  

Abstract High flux reactor is an important engineering test reactor, which can be used in irradiation research of materials, chemistry, isotopes, medicine and other fields. In the high flux reactor coolant system, there are a large number of nuclear pipes and the layout is complex. The optimization of seismic analysis method for reactor coolant system is an important part in the design process to ensure the nuclear pipes meet the design specifications. The traditional single point response spectrum method needs to envelope the response spectrum of different floors as the analysis input. This method is difficult to give the reasonable seismic load to the numerous nuclear pipes and it will increase the design cost and the difficulty of safety analysis about nuclear pipe. In this paper, an optimized seismic analysis method of reactor coolant system is proposed. By using the multi-point response spectrum method, the optimization of different excitation loading modes for different constrained support points is realized. The analysis results show that the multi-point response spectrum method can solve the problem that different support points are located at different elevation floors in the reactor coolant system, which makes the calculation results more accurate and reasonable. Compared with the traditional method, it can make the design more efficient and practical.


Sign in / Sign up

Export Citation Format

Share Document