scholarly journals Turbulent flow and heat transfer characteristics in U-tubes: A numerical study

2009 ◽  
Vol 13 (4) ◽  
pp. 175-181 ◽  
Author(s):  
Khalid Alammar
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Coefficient ◽  
Turbulent Flow ◽  
Skin Friction ◽  
Skin Friction Coefficient ◽  
Heat Transfer Characteristics ◽  
Local Skin ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer

Using the standard k-e model, 3-dimensional turbulent flow and heat transfer characteristics in U-tubes are investigated. Uncertainty is approximated using experimental correlations and grid independence study. Increasing the Dean number is shown to intensify a secondary flow within the curved section. The overall Nusselt number for the tube is found to decrease substantially relative to straight tubes, while the overall skin friction coefficient remains practically unaffected. Local skin friction coefficient, Nusselt number, and wall temperature along the tube wall are presented.

Flow and Heat Transfer Over a Stretched Microsurface

2009 ◽  
Vol 131 (6) ◽  
Author(s):  
Suhil Kiwan ◽  
M. A. Al-Nimr
Keyword(s):  
Heat Transfer ◽  
Friction Coefficient ◽  
Flat Plate ◽  
Skin Friction ◽  
Convection Heat Transfer ◽  
Skin Friction Coefficient ◽  
Slip Parameter ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer

The convection heat transfer induced by a stretching flat plate has been studied. Similarity conditions are obtained for the boundary layer equations for a flat plate subjected to a power law temperature and velocity variations. It is found that a similarity solution exists only for a linearly stretching plate and only when the plate is isothermal. The analysis shows that three parameters control the flow and heat transfer characteristics of the problem. These parameters are the velocity slip parameter K1, the temperature slip parameter K2, and the Prandtl number. The effect of these parameters on the flow and heat transfer of the problem has been studied and presented. It is found that the slip velocity parameter affect both the flow and heat transfer characteristics of the problem. It is found that the skin friction coefficient decreases with increasing K1 and most of the changes in the skin friction takes place in the range 0<K1<1. A correlation between the skin friction coefficient and K1 and Rex has been found and presented. It is found that cf=23Rex−0.5(K1+0.64)−0.884 for 0<K1<10 with an error of ±0.8%. Other correlations between Nu and K1 and K2 has been found and presented in Eq. 28.

scholarly journals Uncertainties Analysis on the Prediction of Flow and Heat Transfer of Liquid Sodium with CFD Technology

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Zhanwei Liu ◽  
Xinyu Li ◽  
Tenglong Cong ◽  
Rui Zhang ◽  
Lingyun Zheng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Coefficient ◽  
Liquid Sodium ◽  
Heat Transfer Characteristics ◽  
Backward Facing Step ◽  
Heating Wall ◽  
Transfer Characteristics ◽  
Cfd Models ◽  
Flow And Heat Transfer

The prediction of flow and heat transfer characteristics of liquid sodium with CFD technology is of significant importance for the design and safety analysis of sodium-cooled fast reactor. The accuracies and uncertainties of the CFD models should be evaluated to improve the confidence of the numerical results. In this work, the uncertainties from the turbulent model, boundary conditions, and physical properties for the flow and heat transfer of liquid sodium were evaluated against the experimental data. The results of uncertainty quantization show that the maximum uncertainties of the Nusselt number and friction coefficient occurred in the transition zone from the inlet to the fully developed region in the circular tube, while they occurred near the reattachment point in the backward-facing step. Furthermore, in backward-facing step flow, the maximum uncertainty of temperature migrated from the heating wall to the geometric center of the channel, while the maximum uncertainty of velocity occurred near the vortex zone. The results of sensitivity analysis illustrate that the Nusselt number was negatively correlated with the thermal conductivity and turbulent Prandtl number, while the friction coefficient was positively correlated with the density and Von Karman constant. This work can be a reference to evaluate the accuracy of the standard k-ε model in predicting the flow and heat transfer characteristics of liquid sodium.

Hybrid nanofluid flow and heat transfer over a nonlinear permeable stretching/shrinking surface

2019 ◽  
Vol 29 (9) ◽  
pp. 3110-3127 ◽  
Author(s):  
Iskandar Waini ◽  
Anuar Ishak ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Local Nusselt Number ◽  
Skin Friction Coefficient ◽  
Hybrid Nanofluid ◽  
Content Type ◽  
Flow And Heat Transfer ◽  
Shrinking Surface

PurposeThis paper aims to investigate the steady flow and heat transfer of a Cu-Al2O3/water hybrid nanofluid over a nonlinear permeable stretching/shrinking surface with radiation effects. The surface velocity condition is assumed to be of the power-law form with an exponent of 1/3. The governing equations of the problem are converted into a system of similarity equations by using a similarity transformation.Design/methodology/approachThe problem is solved numerically using the boundary value problem solver (bvp4c) in Matlab software. The results of the skin friction coefficient and the local Nusselt number as well as the velocity and temperature profiles are presented through graphs and tables for several values of the parameters. The effects of these parameters on the flow and heat transfer characteristics are examined and discussed.FindingsResults found that dual solutions exist for a certain range of the stretching/shrinking and suction parameters. The increment of the skin friction coefficient and reduction of the local Nusselt number on the shrinking sheet is observed with the increasing of copper (Cu) nanoparticle volume fractions for the upper branch. The skin friction coefficient and the local Nusselt number increase when suction parameter is increased for the upper branch. Meanwhile, the temperature increases in the presence of the radiation parameter for both branches.Originality/valueThe problem of Cu-Al2O3/water hybrid nanofluid flow and heat transfer over a nonlinear permeable stretching/shrinking surface with radiation effects is the important originality of the present study where the dual solutions for the flow reversals are obtained.

scholarly journals Magnetohydrodynamic Flow and Heat Transfer Over an Exponentially Stretching/Shrinking Sheet in Ferrofluids

2021 ◽  
Vol 29 (3) ◽  
Author(s):  
Nurfazila Rasli ◽  
Norshafira Ramli
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Coefficient ◽  
Differential Equations ◽  
Skin Friction ◽  
Skin Friction Coefficient ◽  
Magnetohydrodynamic Flow ◽  
Shrinking Sheet ◽  
Flow And Heat Transfer ◽  
Exponentially Stretching

In this research, the problem of magnetohydrodynamic flow and heat transfer over an exponentially stretching/shrinking sheet in ferrofluids is presented. The governing partial differential equations are transformed into nonlinear ordinary differential equations by applying suitable similarity transformations. These equations are then solved numerically using the shooting method for some pertinent parameters. For this research, the water-based ferrofluid is considered with three types of ferroparticles: magnetite, cobalt ferrite, and manganese-zinc ferrite. The numerical solutions on the skin friction coefficient, Nusselt number, velocity and temperature profiles influenced by the magnetic parameter, wall mass transfer parameter, stretching/shrinking parameter, and volume fraction of solid ferroparticle are graphically displayed and discussed in more details. The existences of dual solutions are noticeable for the stretching/shrinking case in a specific range of limit. For the first solution, an increasing number in magnetic and suction will also give an increment of skin friction coefficient and Nusselt number over stretching/shrinking sheet. For the skin friction coefficient only, it is showed a decreasing pattern after the intersection. Besides, the presence of ferroparticles in the fluids causes a high number of the fluid’s thermal conductivity and heat transfer rate.

Investigation Into the Similarity Solution for Boundary Layer Flows in Microsystems

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Suhil Kiwan ◽  
M. A. Al-Nimr
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Temperature Jump ◽  
Velocity Slip ◽  
Skin Friction Coefficient ◽  
Heat Transfer Characteristics ◽  
Boundary Layer Flows ◽  
Flow And Heat Transfer

An investigation toward the existence of a complete similarity solution for boundary layer flows under the velocity slip and temperature jump conditions is carried out. The study is limited to the boundary layer flows resulting from an arbitrary freestream velocity U(x)=Uoxm and wall temperature given by Tw−T∞=Cxn. It is found that a similar solution exists only for m=1 and n=0, which represents stagnation flow on isothermal surface. This case has been thoroughly investigated. The analysis showed that three parameters control the flow and heat transfer characteristics of the problem. These parameters are the velocity slip parameter K1, the temperature jump parameter K2, and Prandtl number. The effect of these parameters on the flow and heat transfer of the problem has been studied and presented. It is found that the slip velocity parameter affects both the flow and heat transfer characteristics of the problem. It is found that the skin friction coefficient decreases with increasing K1 and most of changes in the skin friction takes place in the range 0<K1<1. The skin friction coefficient is found to be related to K1 and Rex according to the relation: Cf=3.38Rex−0.5(K1+1.279)−0.8 for 0<K1<5 with an error of ±4%. On the other hand, the correlation between Nu, K1, K2, and Pr has been found by the equation Nu=[(0.449+1.142K11.06)∕(0.515+K11.06)](K2+1.489Pr−0.44)−1, for 0<K1, K2<5, 0.7≤Pr≤5 within a maximum error of ±3%.

scholarly journals Boundary-layer flow and heat transfer of cross fluid over a stretching sheet

2019 ◽  
Vol 23 (1) ◽  
pp. 307-318 ◽  
Author(s):  
Masood Khan ◽  
Mehwish Manzur ◽  
Masood Rahman
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Nusselt Number ◽  
Friction Coefficient ◽  
Stretching Sheet ◽  
Skin Friction Coefficient ◽  
Weissenberg Number ◽  
Local Skin ◽  
Flow And Heat Transfer ◽  
Local Skin Friction

The current study is a pioneering work in presenting the boundary-layer equations for the 2-D flow and heat transfer of the Cross fluid over a linearly stretching sheet. The system of PDE is turned down into highly non-linear ODE by applying suitable similarity transformations. The stretching sheet solutions are presented via. a numerical technique namely the shooting method and graphs are constructed. The impact of the emerging parameters namely the power-law index, n, the local Weissenberg number, We, and the Prandtl number on the velocity and temperature fields are investigated through graphs. The numerical values of the local skin friction coefficient and the local Nusselt number are also presented in tabular form. Additionally, the graphs are sketched for the local skin friction coefficient and the local Nusselt number. It is observed that with growing values of the local Weissenberg number the velocity profiles exhibited a decreasing trend while opposite behavior is seen for the temperature field. Further, comparisons are made with previously available literature for some limiting cases and an excellent agreement is achieved.

scholarly journals Heat Transfer Improvement in a Double Backward-Facing Expanding Channel Using Different Working Fluids

Symmetry ◽  
2020 ◽  
Vol 12 (7) ◽  
pp. 1088 ◽  
Author(s):  
Tuqa Abuldrazzaq ◽  
Hussein Togun ◽  
Hamed Alsulami ◽  
Marjan Goodarzi ◽  
Mohammad Reza Safaei
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Thermal Performance ◽  
Skin Friction Coefficient ◽  
Local Skin ◽  
Heat Transfer Improvement ◽  
Expanding Channel

This paper reports a numerical study on heat transfer improvement in a double backward-facing expanding channel using different convectional fluids. A finite volume method with the k-ε standard model is used to investigate the effects of step, Reynolds number and type of liquid on heat transfer enhancement. Three types of conventional fluids (water, ammonia liquid and ethylene glycol) with Reynolds numbers varying from 98.5 to 512 and three cases for different step heights at a constant heat flux (q = 2000 W/m2) are examined. The top wall of the passage and the bottom wall of the upstream section are adiabatic, while the walls of both the first and second steps downstream are heated. The results show that the local Nusselt number rises with the augmentation of the Reynolds number, and the critical effects are seen in the entrance area of the first and second steps. The maximum average Nusselt number, which represents the thermal performance, can be seen clearly in case 1 for EG in comparison to water and ammonia. Due to the expanding of the passage, separation flow is generated, which causes a rapid increment in the local skin friction coefficient, especially at the first and second steps of the downstream section for water, ammonia liquid and EG. The maximum skin friction coefficient is detected in case 1 for water with Re = 512. Trends of velocities for positions (X/H1 = 2.01, X/H2 = 2.51) at the first and second steps for all the studied cases with different types of convectional fluids are indicated in this paper. The presented findings also include the contour of velocity, which shows the recirculation zones at the first and second steps to demonstrate the improvement in the thermal performance.

scholarly journals Effect of Prandtl number on heat transfer characteristics in an axisymmetric sudden expansion: A numerical study

2007 ◽  
Vol 11 (4) ◽  
pp. 171-178
Author(s):  
Khalid Alammar
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Prandtl Number ◽  
Turbulent Flow ◽  
Turbulence Model ◽  
Numerical Study ◽  
Sudden Expansion ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Simulated Effect

Using the standard k-e turbulence model, an incompressible, axisymmetric turbulent flow with a sudden expansion was simulated. Effect of Prandtl number on heat transfer characteristics downstream of the expansion was investigated. The simulation revealed circulation downstream of the expansion. A secondary circulation (corner eddy) was also predicted. Reattachment was predicted at approximately 10 step heights. Corresponding to Prandtl number of 7.0, a peak Nusselt number 13 times the fully-developed value was predicted. The ratio of peak to fully-developed Nusselt number was shown to decrease with decreasing Prandtl number. Location of maximum Nusselt number was insensitive to Prandtl number.

Sign in / Sign up

Export Citation Format

Share Document