Investigation Into the Similarity Solution for Boundary Layer Flows in Microsystems

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Suhil Kiwan ◽  
M. A. Al-Nimr
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Temperature Jump ◽  
Velocity Slip ◽  
Skin Friction Coefficient ◽  
Heat Transfer Characteristics ◽  
Boundary Layer Flows ◽  
Flow And Heat Transfer

An investigation toward the existence of a complete similarity solution for boundary layer flows under the velocity slip and temperature jump conditions is carried out. The study is limited to the boundary layer flows resulting from an arbitrary freestream velocity U(x)=Uoxm and wall temperature given by Tw−T∞=Cxn. It is found that a similar solution exists only for m=1 and n=0, which represents stagnation flow on isothermal surface. This case has been thoroughly investigated. The analysis showed that three parameters control the flow and heat transfer characteristics of the problem. These parameters are the velocity slip parameter K1, the temperature jump parameter K2, and Prandtl number. The effect of these parameters on the flow and heat transfer of the problem has been studied and presented. It is found that the slip velocity parameter affects both the flow and heat transfer characteristics of the problem. It is found that the skin friction coefficient decreases with increasing K1 and most of changes in the skin friction takes place in the range 0<K1<1. The skin friction coefficient is found to be related to K1 and Rex according to the relation: Cf=3.38Rex−0.5(K1+1.279)−0.8 for 0<K1<5 with an error of ±4%. On the other hand, the correlation between Nu, K1, K2, and Pr has been found by the equation Nu=[(0.449+1.142K11.06)∕(0.515+K11.06)](K2+1.489Pr−0.44)−1, for 0<K1, K2<5, 0.7≤Pr≤5 within a maximum error of ±3%.

Flow and Heat Transfer Over a Stretched Microsurface

2009 ◽  
Vol 131 (6) ◽  
Author(s):  
Suhil Kiwan ◽  
M. A. Al-Nimr
Keyword(s):  
Heat Transfer ◽  
Friction Coefficient ◽  
Flat Plate ◽  
Skin Friction ◽  
Convection Heat Transfer ◽  
Skin Friction Coefficient ◽  
Slip Parameter ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer

The convection heat transfer induced by a stretching flat plate has been studied. Similarity conditions are obtained for the boundary layer equations for a flat plate subjected to a power law temperature and velocity variations. It is found that a similarity solution exists only for a linearly stretching plate and only when the plate is isothermal. The analysis shows that three parameters control the flow and heat transfer characteristics of the problem. These parameters are the velocity slip parameter K1, the temperature slip parameter K2, and the Prandtl number. The effect of these parameters on the flow and heat transfer of the problem has been studied and presented. It is found that the slip velocity parameter affect both the flow and heat transfer characteristics of the problem. It is found that the skin friction coefficient decreases with increasing K1 and most of the changes in the skin friction takes place in the range 0<K1<1. A correlation between the skin friction coefficient and K1 and Rex has been found and presented. It is found that cf=23Rex−0.5(K1+0.64)−0.884 for 0<K1<10 with an error of ±0.8%. Other correlations between Nu and K1 and K2 has been found and presented in Eq. 28.

scholarly journals Turbulent flow and heat transfer characteristics in U-tubes: A numerical study

2009 ◽  
Vol 13 (4) ◽  
pp. 175-181 ◽  
Author(s):  
Khalid Alammar
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Coefficient ◽  
Turbulent Flow ◽  
Skin Friction ◽  
Skin Friction Coefficient ◽  
Heat Transfer Characteristics ◽  
Local Skin ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer

Using the standard k-e model, 3-dimensional turbulent flow and heat transfer characteristics in U-tubes are investigated. Uncertainty is approximated using experimental correlations and grid independence study. Increasing the Dean number is shown to intensify a secondary flow within the curved section. The overall Nusselt number for the tube is found to decrease substantially relative to straight tubes, while the overall skin friction coefficient remains practically unaffected. Local skin friction coefficient, Nusselt number, and wall temperature along the tube wall are presented.

scholarly journals A Non-Newtonian Magnetohydrodynamics (MHD) Nanofluid Flow and Heat Transfer with Nonlinear Slip and Temperature Jump

Mathematics ◽  
2019 ◽  
Vol 7 (12) ◽  
pp. 1199 ◽  
Author(s):  
Jing Zhu ◽  
Yaxin Xu ◽  
Xiang Han
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Temperature Jump ◽  
Thin Sheet ◽  
Velocity Slip ◽  
Skin Friction Coefficient ◽  
Slip Condition ◽  
Physical Parameters ◽  
Nanofluid Flow ◽  
Flow And Heat Transfer

The velocity and thermal slip impacts on the magnetohydrodynamics (MHD) nanofluid flow and heat transfer through a stretched thin sheet are discussed in the paper. The no slip condition is substituted for a new slip condition consisting of higher-order slip and constitutive equation. Similarity transformation and Lie point symmetry are adopted to convert the derived governed equations to ordinary differential equations. An approximate analytical solution is gained through the homotopy analysis method. The impacts of velocity slip, temperature jump, and other physical parameters on flow and heat transfer are illustrated. Results indicate that the first-order slip and nonlinear slip parameters reduce the velocity boundary layer thickness and Nusselt number, whereas the effect on shear stress is converse. The temperature jump parameter causes a rise in the temperature, but a decline in the Nusselt number. With the increase of the order, we can get that the error reaches 10 − 6 from residual error curve. In addition, the velocity contours and the change of skin friction coefficient are computed through Ansys Fluent.

Hybrid nanofluid flow and heat transfer over a nonlinear permeable stretching/shrinking surface

2019 ◽  
Vol 29 (9) ◽  
pp. 3110-3127 ◽  
Author(s):  
Iskandar Waini ◽  
Anuar Ishak ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Local Nusselt Number ◽  
Skin Friction Coefficient ◽  
Hybrid Nanofluid ◽  
Content Type ◽  
Flow And Heat Transfer ◽  
Shrinking Surface

PurposeThis paper aims to investigate the steady flow and heat transfer of a Cu-Al2O3/water hybrid nanofluid over a nonlinear permeable stretching/shrinking surface with radiation effects. The surface velocity condition is assumed to be of the power-law form with an exponent of 1/3. The governing equations of the problem are converted into a system of similarity equations by using a similarity transformation.Design/methodology/approachThe problem is solved numerically using the boundary value problem solver (bvp4c) in Matlab software. The results of the skin friction coefficient and the local Nusselt number as well as the velocity and temperature profiles are presented through graphs and tables for several values of the parameters. The effects of these parameters on the flow and heat transfer characteristics are examined and discussed.FindingsResults found that dual solutions exist for a certain range of the stretching/shrinking and suction parameters. The increment of the skin friction coefficient and reduction of the local Nusselt number on the shrinking sheet is observed with the increasing of copper (Cu) nanoparticle volume fractions for the upper branch. The skin friction coefficient and the local Nusselt number increase when suction parameter is increased for the upper branch. Meanwhile, the temperature increases in the presence of the radiation parameter for both branches.Originality/valueThe problem of Cu-Al2O3/water hybrid nanofluid flow and heat transfer over a nonlinear permeable stretching/shrinking surface with radiation effects is the important originality of the present study where the dual solutions for the flow reversals are obtained.

Boundary layer flow near stagnation-points on a vertical surface with slip in the presence of transverse magnetic field

2014 ◽  
Vol 24 (3) ◽  
pp. 643-653 ◽  
Author(s):  
Ibrahim Yakubu Seini ◽  
Daniel Oluwole Makinde
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Boundary Layer ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Stagnation Point ◽  
Vertical Surface ◽  
Skin Friction Coefficient ◽  
Content Type ◽  
Layer Flow

Purpose – The purpose of this paper is to investigate the MHD boundary layer flow of viscous, incompressible and electrically conducting fluid near a stagnation-point on a vertical surface with slip. Design/methodology/approach – In the study, the temperature of the surface and the velocity of the external flow are assumed to vary linearly with the distance from the stagnation-point. The governing differential equations are transformed into systems of ordinary differential equations and solved numerically by a shooting method. Findings – The effects of various parameters on the heat transfer characteristics are discussed. Graphical results are presented for the velocity and temperature profiles whilst the skin-friction coefficient and the rate of heat transfers near the surface are presented. It is observed that the presence of the magnetic field increases the skin-friction coefficient and the rate of heat transfer near the surface towards the stagnation-point. Originality/value – The presence of magnetic field increases the skin-friction coefficient and the rate of heat transfer near the surface towards the stagnation-point.

Investigation of Flat-Plate Hypersonic, Turbulent Boundary Layers With Heat Transfer

1961 ◽  
Vol 28 (3) ◽  
pp. 323-329 ◽  
Author(s):  
Eva M. Winkler
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Friction Coefficient ◽  
Mach Number ◽  
Flat Plate ◽  
Skin Friction ◽  
Boundary Layers ◽  
Skin Friction Coefficient ◽  
Turbulent Boundary Layers ◽  
Reynolds Analogy

Naturally turbulent boundary layers on a cooled flat plate have been investigated at several distances from the leading edge of the plate at a Mach number of 5.2 for three rates of steady-state heat transfer to the surface. Measurements of Pitot and static pressures and of total and wall temperatures made it possible to compute velocity profiles, static-temperature profiles, and boundary-layer parameters without resorting to assumptions. The data demonstrate that the Reynolds analogy between skin friction and heat transfer is valid for all conditions of the present experiments. With increasing rate of heat transfer to the surface, the skin-friction coefficient was found to decrease, a phenomenon opposite to that predicted by theories and empirical relations. On the basis of the present data and other published results of compressible and incompressible turbulent boundary-layer skin friction, a simple relation was devised which describes closely the variation of the skin-friction coefficient with Mach number, heat-transfer rate, and momentum-thickness Reynolds number.

Effects of Regular and Random Roughness on the Heat Transfer and Skin Friction Coefficient on the Suction Side of a Gas Turbine Vane

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
Jason E. Dees ◽  
David G. Bogard
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Suction Side ◽  
Skin Friction Coefficient ◽  
Regular Array ◽  
Roughness Elements ◽  
Turbine Vane ◽  
Regular Roughness

Skin friction coefficients and heat transfer coefficients are measured for a range of regular and random roughnesses on the suction side of a simulated gas turbine vane. The skin friction coefficients are calculated using boundary layer data and the momentum integral method. High resolution surface temperature data measured with an IR camera yield local heat transfer values. 80 grit, 50 grit, 36 grit, and 20 grit sandpapers along with a regular array of conical roughness elements are tested. Measured skin friction coefficient data show that the conical roughness array behaves very similar to the 50 grit, 36 grit, and 20 grit sandpapers in terms of the effect of the roughness on the hydrodynamic boundary layer. In terms of heat transfer, the conical roughness array is most similar to the 80 grit sandpaper, which are both lower than the roughest sandpapers tested. These data show that the particular regular array of roughness elements tested has fundamentally different behavior than randomly rough surfaces for this position on the simulated turbine vane. In addition, this difference is in the opposite direction as seen in previous experimental studies. In order to draw a more general conclusion about the nature of random and regular roughness, a parametric study of regular roughness arrays should be performed.

Hydromagnetic flow and heat transfer with various nanoparticle additives past a wedge with high order velocity slip and temperature jump

2017 ◽  
Vol 95 (5) ◽  
pp. 440-449 ◽  
Author(s):  
Qianfang Liu ◽  
Jing Zhu ◽  
Bandar Bin-Mohsin ◽  
Liancun Zheng
Keyword(s):  
Heat Transfer ◽  
Temperature Jump ◽  
Slip Flow ◽  
Velocity Slip ◽  
Skin Friction Coefficient ◽  
High Order ◽  
Solid Particles ◽  
Flow And Heat Transfer ◽  
Homotopy Analysis ◽  
Fundamental Equations

Nanofluid slip flow with distinct solid particles past a wedge with convective surface and high order slip is discussed in this paper. The wedge model is modified by considering the effects of Brownian motion and thermophphoresis together with the high order velocity slip and temperature jump. In this study, the governing fundamental equations are first transformed into third-order ordinary differential equations and solved by using the homotopy analysis method (HAM). Through error analysis and comparison with previous research, the effectiveness of HAM is ascertained, and the crucial influence of nanoparticles and high-order slip on the fluid skin-friction coefficient and heat transfer coefficient is analyed. Thermophphoresis parameter and suction/injection parameter are found to cause an increase in velocity and temperature. The rate of heat transfer in the Cu–water nanofluid is found to be higher than the others.

Effects of Regular and Random Roughness on the Heat Transfer and Skin Friction Coefficient on the Suction Side of a Gas Turbine Vane

2007 ◽  
Author(s):  
Jason E. Dees ◽  
David G. Bogard
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Suction Side ◽  
Skin Friction Coefficient ◽  
Regular Array ◽  
Roughness Elements ◽  
Turbine Vane ◽  
Regular Roughness

Skin friction coefficients and heat transfer coefficients are measured for a range of regular and random roughnesses on the suction side of a simulated gas turbine vane. The skin friction coefficients are calculated using boundary layer data and the momentum integral method. High resolution surface temperature data measured with an IR camera yields local heat transfer values. 80 grit, 50 grit, 36 grit, and 20 grit sandpaper, along with a regular array of conical roughness elements are tested. Measured skin friction coefficient data shows that the conical roughness array behaves very similarly to the 50 grit, 36 grit, and 20 grit sandpapers in terms of the effect of the roughness on the hydrodynamic boundary layer. In terms of heat transfer, the conical roughness array is most similar to the 80 grit sandpaper, which are both lower than the roughest sandpapers tested. This data shows that the particular regular array of roughness elements tested has fundamentally different behavior than randomly rough surfaces for this position on the simulated turbine vane. In addition, this difference is in the opposite direction as seen in previous experimental studies. In order to draw a more general conclusion about the nature of random and regular roughness, a parametric study of regular roughness arrays should be performed.

Sign in / Sign up

Export Citation Format

Share Document