scholarly journals Heat transfer coefficient in elliptical tube at the constant heat flux

2019 ◽  
Vol 23 (Suppl. 4) ◽  
pp. 1323-1332
Author(s):  
Stanislaw Lopata ◽  
Pawel Oclon ◽  
Tomasz Stelmach ◽  
Pawel Markowski
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Cross Section ◽  
Measurement Data ◽  
Constant Heat Flux ◽  
Working Fluid ◽  
Constant Heat ◽  
The Heat Transfer Coefficient

Cross-flow heat exchangers with elliptical tubes are often used in industrial application. In comparison with round tubes, the elliptical tubes have a better aero-dynamic shape, which results in a lower pressure drop of working fluid flowing through the inter-tubular space of heat exchanger. Also, a higher heat flux is transferred from gas to the wall of such a tube due to the more intense heat exchange process. To prove this thesis, the values of the heat transfer coefficient from the wall of the elliptical pipe to the water flowing inside were determined, using the data from the conducted measurements. This study presents also research stand with a vertically positioned tube. In order to obtain a constant heat flux through the wall of elliptical tube, a resistance wire is used, evenly wound on the external surface of tube measuring section. The use of thermal insulation minimized heat loss to the environment to a negligible value. Installed K-type thermocouples allowed one to obtain, for various measurement conditions, the temperature distribution within the elliptical tube wall (for a given cross-section) and the water flowing inside it (in a given cross-section, at different depths, for both axes of the ellipse). The design of the stand allows such measurements in several locations along the length of the measurement section. The measurement results were used to verify numerical calculations. The relative error of the heat transfer coefficient value determined on the basis of CFD calculations using the SST-TR turbulence model in relation to the one determined on the basis of the measurement data is about 11%.

Numerical investigation of CuO-water nanofluid turbulent convective heat transfer in square cross-section duct under constant heat flux

2016 ◽  
Vol 33 (6) ◽  
pp. 1714-1728 ◽  
Author(s):  
Hsien-Hung Ting ◽  
Shuhn-Shyurng Hou
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Cross Section ◽  
Convective Heat ◽  
Constant Heat Flux ◽  
Constant Heat ◽  
Content Type

Purpose – The purpose of this paper is to numerically investigate the convective heat transfer of water-based CuO nanofluids flowing through a square cross-section duct under constant heat flux in the turbulent flow regime. Design/methodology/approach – The numerical simulation is carried out at various Peclet numbers and particle concentrations (0.1, 0.2, 0.5, and 0.8 vol%). The finite volume formulation is used with the semi-implicit method for pressure-linked equations algorithm to solve the discretized equations derived from the partial nonlinear differential equations of the mathematical model. Findings – The heat transfer coefficients and Nusselt numbers of CuO-water nanofluids increase with increases in the Peclet number as well as particle volume concentration. Also, enhancement of the heat transfer coefficient is much greater than that of the effective thermal conductivity at the same nanoparticle concentration. Research limitations/implications – Simulation of nanofluids turbulent forced convection at very high Reynolds number is worth for further study. Practical implications – The heat transfer rates through non-circular ducts are smaller than the circular tubes. Nevertheless, the pressure drop of the non-circular duct is less than that of the circular tube. This study clearly presents that the nanoparticles suspended in water enhance the convective heat transfer coefficient, despite low volume fraction between 0.1 and 0.8 percent. Adding nanoparticles to conventional fluids may enhance heat transfer performance through the non-circular ducts, leading to extensive practical applications in industries for the non-circular ducts. Originality/value – Few papers have numerically studied convective heat transfer properties of nanofluids through non-circular ducts. The present numerical results show a good agreement with the published experimental data.

Two Phase Heat Transfer of Ammonia in a Mini/Micro Channel

2010 ◽  
Author(s):  
M. Hamayun Maqbool ◽  
Bjo¨rn Palm ◽  
R. Khodabandeh ◽  
Rashid Ali
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Mass Flux ◽  
Experimental Results ◽  
Working Fluid ◽  
Internal Diameter ◽  
Vapour Quality ◽  
The Heat Transfer Coefficient

Experiments have been performed to investigate heat transfer in a circular vertical mini channel made of stainless steel (AISI 316) with internal diameter of 1.70 mm and a uniformly heated length of 245 mm using ammonia as working fluid. The experiments are conducted for a heat flux range of 15 to 350 kW/m2 and mass flux range of 100 to 500 kg/m2s. The effects of heat flux, mass flux and vapour quality on the heat transfer coefficient are explored in detail. The experimental results show that the heat transfer coefficient increases with imposed wall heat flux while mass flux and vapour quality have no considerable effect. Experimental results are compared to predictive methods available in the literature for boiling heat transfer. The correlations of Cooper et al. [1] and Shah [3] are in good agreement with our experimental data.

Heat Transfer Characteristics of CuO-Base Oil Nanofluid Laminar Flow Inside Flattened Tubes Under Constant Heat Flux

2010 ◽  
Author(s):  
P. Razi ◽  
M. A. Akhavan-Behabadi
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Constant Heat Flux ◽  
Electrical Heating ◽  
Heat Transfer Characteristics ◽  
Constant Heat ◽  
Base Oil ◽  
Transfer Characteristics

An experimental investigation has been carried out to study the heat transfer characteristics of CuO-Base oil nanofluid flow inside horizontal flattened tubes under constant heat flux. The nanofluid flowing inside the tube is heated by an electrical heating coil wrapped around it. The convective heat transfer coefficients of nanofluids are obtained for laminar fully developed flow inside round and flattened tubes. The effect of different parameters such as Reynolds number, flattened tube internal height, nanoparticles concentration and heat flux on heat transfer coefficient is studied. Observations show that the heat transfer performance is improved as the tube profile is flattened. The heat transfer coefficient is increased by using nanofluid instead of base fluid. Also, it can be concluded that decreasing the internal height of the flattened tubes and increasing the concentration of nanoparticles both contribute to the enhancement of heat transfer coefficient.

An Empirical Study on Heat Transfer Characteristics of CuO/Base Oil Nanofluid Flow in a Tube With Coiled Wire Inserts

2010 ◽  
Author(s):  
M. A. Akhavan-Behabadi ◽  
M. Saeedinia ◽  
S. M. Hashemi
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Constant Heat Flux ◽  
Wire Diameter ◽  
Heat Transfer Characteristics ◽  
Nanofluid Flow ◽  
Base Oil ◽  
The Heat Transfer Coefficient

In the present study, an experimental investigation has been carried out to study the heat transfer characteristics of CuO/Base oil nanofluid flow inside horizontal oiled wire inserted tubes (roughed tubes) under constant heat flux. The nanofluids with CuO nanoparticles weight fraction ranging from 0 to 2% are prepared. The oiled wires with different wire wire diameteres and different oil pitches are used as inserts inside a horizontal plain copper tube. The nanofluid flowing inside the tube is heated by electrical heating coil wrapped around it. The convective heat transfer characteristis of the prepared nanofluids are measured during laminar fully developed flow inside horizontal plain and roughed tubes under constant heat flux. The effect of different parameters such as mass velocity, wire wire diameter, oil pith, nanofluid particles concentration and heat flux on heat transfer coefficient is studied. The heat transfer coefficient is increased when a roughed tube is used instead of a plain tube. Moreover, at the same flow conditions, by increasing of wire wire diameter and decreasing of oil pitch, the heat transfer performance is improved. Observations also show that by using nanofluid instead of base fluid, the heat transfer coefficient increases and this increase grows at higher nanoparticles concentrations. As a result, it an be concluded that increasing of wire wire diameter, decreasing of oil pitch and increasing the concentration of nanoparticle, contribute to the enhancement of heat transfer coefficient.

Flow Boiling Heat Transfer Characteristics of a Minichannel Up to Dryout Condition

2009 ◽  
Author(s):  
Rashid Ali ◽  
Bjo¨rn Palm ◽  
Mohammad H. Maqbool
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Working Fluid ◽  
Flow Boiling Heat Transfer ◽  
The Heat Transfer Coefficient

In this paper the experimental flow boiling heat transfer results of a minichannel are presented. A series of experiments was conducted to measure the heat transfer coefficients in a minichannel made of stainless steel (AISI 316) having an internal diameter of 1.7mm and a uniformly heated length of 220mm. R134a was used as working fluid and experiments were performed at two different system pressures corresponding to saturation temperatures of 27 °C and 32 °C. Mass flux was varied from 50 kg/m2 s to 600 kg/m2 s and heat flux ranged from 2kW/m2 to 156kW/m2. The test section was heated directly using a DC power supply. The direct heating of the channel ensured uniform heating and heating was continued until dry out was reached. The experimental results show that the heat transfer coefficient increases with imposed wall heat flux while mass flux and vapour quality have no considerable effect. Increasing the system pressure slightly enhances the heat transfer coefficient. The heat transfer coefficient is reduced as dryout is reached. It is observed that dryout phenomenon is accompanied with fluctuations and a larger standard deviation in outer wall temperatures.

Flow Boiling Heat Transfer Characteristics of a Minichannel up to Dryout Condition

2011 ◽  
Vol 133 (8) ◽  
Author(s):  
Rashid Ali ◽  
Björn Palm ◽  
Mohammad H. Maqbool
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Working Fluid ◽  
Flow Boiling Heat Transfer ◽  
The Heat Transfer Coefficient

In this paper, the experimental flow boiling heat transfer results of a minichannel are presented. A series of experiments was conducted to measure the heat transfer coefficients in a minichannel made of stainless steel (AISI 316) having an internal diameter of 1.70 mm and a uniformly heated length of 220 mm. R134a was used as a working fluid, and experiments were performed at two different system pressures corresponding to saturation temperatures of 27°C and 32°C. Mass flux was varied from 50 kg/m2 s to 600 kg/m2 s, and heat flux ranged from 2 kW/m2 to 156 kW/m2. The test section was heated directly using a dc power supply. The direct heating of the channel ensured uniform heating, which was continued until dryout was reached. The experimental results show that the heat transfer coefficient increases with imposed wall heat flux, while mass flux and vapor quality have no considerable effect. Increasing the system pressure slightly enhances the heat transfer coefficient. The heat transfer coefficient is reduced as dryout is reached. It is observed that the dryout phenomenon is accompanied with fluctuations and a larger standard deviation in outer wall temperatures.

Heat Transfer Coefficient Augmentation for a Shaped Film Cooling Hole at a Range of Compound Angles

2020 ◽  
pp. 1-30
Author(s):  
Shane Haydt ◽  
Stephen Lynch
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Constant Heat Flux ◽  
Cooling Hole ◽  
Adiabatic Effectiveness ◽  
Compound Angle ◽  
The Heat Transfer Coefficient

Abstract Film cooling holes with shaped diffusers are used to efficiently deliver coolant to the surface of a gas turbine part to keep metal temperatures low. Reducing the heat flux into a component, relative to a case with no coolant injection, is the ultimate goal of film cooling. This reduction in heat flux is primarily achieved via a lower driving temperature at the wall for convection, represented by the adiabatic effectiveness. Another important consideration, however, is how the disturbance to the flowfield and thermal field caused by the injection of coolant augments the heat transfer coefficient. The present study examines the spatially-resolved heat transfer coefficient augmentation, measured using a constant heat flux foil and IR thermography, for a shaped film cooling hole at a range of compound angles. Results show that the heat transfer coefficient increases with compound angle and with blowing ratio. Due to the unique asymmetric flowfield of a compound angle hole, a significant amount of augmentation occurs to the side of the film cooling jet, where very little coolant is present. This causes local regions of increased heat flux, which is counter to the goal of film cooling. Heat transfer results are compared with adiabatic effectiveness and flowfield measurements from a previous study.

Heat Transfer Coefficient Augmentation for a Shaped Film Cooling Hole at a Range of Compound Angles

2019 ◽  
Author(s):  
Shane Haydt ◽  
Stephen Lynch
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Constant Heat Flux ◽  
Cooling Hole ◽  
Adiabatic Effectiveness ◽  
Compound Angle ◽  
The Heat Transfer Coefficient

Abstract Shaped film cooling holes are used to efficiently deliver coolant to the surface of a gas turbine part to keep metal temperatures low. The ultimate goal of film cooling is to reduce the heat flux into a component, relative to a case with no coolant injection. This reduction in heat flux is primarily achieved via a lower driving temperature at the wall for convection, represented by the adiabatic effectiveness. Another important consideration, however, is how the disturbance to the flowfield and thermal field caused by the injection of coolant augments the heat transfer coefficient. The present study examines the spatially-resolved heat transfer coefficient augmentation for a shaped film cooling hole at a range of compound angles, using a constant heat flux foil and IR thermography. Results show that the heat transfer coefficient increases with compound angle and with blowing ratio. Due to the unique asymmetric flowfield of a compound angle hole, a significant amount of augmentation occurs to the side of the film cooling jet, where very little coolant is present. This causes local regions of increased heat flux, which is counter to the goal of film cooling. Heat transfer results are compared with adiabatic effectiveness and flowfield measurements from a previous study.

Nanoparticle aggregation kinematics on the quadratic convective magnetohydrodynamic flow of nanomaterial past an inclined flat plate with sensitivity analysis

2021 ◽  
pp. 095440892110562
Author(s):  
AS Sabu ◽  
Joby Mackolil ◽  
B Mahanthesh ◽  
Alphonsa Mathew
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Sensitivity Analysis ◽  
Heat Transfer Coefficient ◽  
Heat Source ◽  
Transfer Coefficient ◽  
Flat Plate ◽  
Inclined Plate ◽  
The Impact ◽  
The Heat Transfer Coefficient

The study focuses on the aggregation kinematics in the quadratic convective magneto-hydrodynamics of ethylene glycol-titania ([Formula: see text]) nanofluid flowing through an inclined flat plate. The modified Krieger-Dougherty and Maxwell-Bruggeman models are used for the effective viscosity and thermal conductivity to account for the aggregation aspect. The effects of an exponential space-dependent heat source and thermal radiation are incorporated. The impact of pertinent parameters on the heat transfer coefficient is explored by using the Response Surface Methodology and Sensitivity Analysis. The effects of several parameters on the skin friction and heat transfer coefficient at the plate are displayed via surface graphs. The velocity and thermal profiles are compared for two physical scenarios: flow over a vertical plate and flow over an inclined plate. The nonlinear problem is solved using the Runge–Kutta-based shooting technique. It was found that the velocity profile significantly decreased as the inclination of the plate increased on the other hand the temperature profile improved. The heat transfer coefficient decreased due to the increase in the Hartmann number. The exponential heat source has a decreasing effect on the heat flux and the angle of inclination is more sensitive to the heat transfer coefficient than other variables. Further, when radiation is incremented, the sensitivity of the heat flux toward the inclination angle augments at the rate 0.5094% and the sensitivity toward the exponential heat source augments at the rate 0.0925%. In addition, 41.1388% decrement in wall shear stress is observed when the plate inclination is incremented from [Formula: see text] to [Formula: see text].

scholarly journals CFD-Entropy generation analysis of refrigerant-based nanofluids flow in a tube

2020 ◽  
Vol 307 ◽  
pp. 01038
Author(s):  
Mohammed Zohud ◽  
Ahmed Ouadha ◽  
Redouane Benzeguir
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Entropy Generation ◽  
Constant Heat Flux ◽  
Flux Boundary Condition ◽  
Flow Heat ◽  
Heat Flux Boundary Condition ◽  
The Heat Transfer Coefficient

The present paper aims to numerically investigate the flow, heat transfer and entropy generation of some hydrocarbon based nanorefrigerants flowing in a circular tube subject to constant heat flux boundary condition. Numerical tests have been performed for 4 types of nanoparticles, namely Al2O3, CuO, SiO2, and ZnO with a diameter equal to 30 nm and a volume concentration of φ = 5%. These nanoparticles are dispersed in some hydrocarbon-based refrigerants, namely tetrafluoroethane (R134a), propane (R290), butane (R600), isobutane (R600a) and propylene (R1270). Computations have been performed for Reynolds number ranging from 600 to 2200. The numerical results in terms of the average heat transfer coefficient of pure refrigerants have been compared to values obtained using correlations from the literature. The results show that the increase of the Reynolds number increases the heat transfer coefficient and decreases the total entropy generation.

Sign in / Sign up

Export Citation Format

Share Document