Design and Wind Tunnel Test Validation of Gust Load Alleviation Systems

2017 ◽  
Author(s):  
Sergio Ricci ◽  
Alessandro De Gaspari ◽  
Luca Riccobene ◽  
Federico Fonte
Keyword(s):  
Wind Tunnel ◽  
Wind Tunnel Test ◽  
Test Validation ◽  
Gust Load Alleviation

scholarly journals Gust Load Alleviation including Geometric Nonlinearities Based on Dynamic Linearization of Structural ROM

2019 ◽  
Vol 2019 ◽  
pp. 1-20
Author(s):  
Chao An ◽  
Chao Yang ◽  
Changchuan Xie ◽  
Yang Meng
Keyword(s):  
Wind Tunnel ◽  
Wind Tunnel Test ◽  
Kernel Functions ◽  
Structural Deformation ◽  
Control Technique ◽  
Feedback Signal ◽  
Response Analysis ◽  
Geometric Nonlinearities ◽  
Gust Load Alleviation ◽  
Gust Response

This paper describes a framework for an active control technique applied to gust load alleviation (GLA) of a flexible wing, including geometric nonlinearities. Nonlinear structure reduced order model (ROM) and nonplanar double-lattice method (DLM) are used for structural and aerodynamic modeling. The structural modeling method presented herein describes stiffness nonlinearities in polynomial formulation. Nonlinear stiffness can be derived by stepwise regression. Inertia terms are constant with linear approximation. Boundary conditions and kernel functions in the nonplanar DLM are determined by structural deformation to reflect a nonlinear effect. However, the governing equation is still linear. A state-space equation is established in a dynamic linearized system around the prescribed static equilibrium state after nonlinear static aeroelastic analysis. Gust response analysis can be conducted subsequently. For GLA analysis, a classic proportional-integral-derivative (PID) controller treats a servo as an actuator and acceleration as the feedback signal. Moreover, a wind tunnel test has been completed and the effectiveness of the control technology is validated. A remote-controlled (RC) model servo is chosen in the wind tunnel test. Numerical simulation results of gust response analysis reach agreement with test results. Furthermore, the control system gives GLA efficacy of vertical acceleration and root bending moment with the reduction rate being over 20%. The method described in this paper is suitable for gust response analysis and control strategy design for large flexible wings.

scholarly journals Design and Optimization of an Aeroservoelastic Wind Tunnel Model

Fluids ◽  
2020 ◽  
Vol 5 (1) ◽  
pp. 35 ◽  
Author(s):  
Johannes K. S. Dillinger ◽  
Yasser M. Meddaikar ◽  
Jannis Lübker ◽  
Manuel Pusch ◽  
Thiemo Kier
Keyword(s):  
Finite Element ◽  
Wind Tunnel ◽  
Wind Tunnel Test ◽  
Objective Functions ◽  
Dynamic Identification ◽  
Wind Tunnel Model ◽  
Design And Optimization ◽  
Aeroelastic Model ◽  
Tunnel Model ◽  
Gust Load Alleviation

Through the combination of passive and active load alleviation techniques, this paper presents the design, optimization, manufacturing, and update of a flexible composite wind tunnel model. In a first step, starting from the specification of an adequate wing and trailing edge flap geometry, passive, static aeroelastic stiffness optimizations for various objective functions have been performed. The second optimization step comprised a discretization of the continuous stiffness distributions, resulting in manufacturable stacking sequences. In order to determine which of the objective functions investigated in the passive structural optimization most efficiently complemented the projected active control schemes, the condensed modal finite element models were integrated in an aeroelastic model, involving a dedicated gust load alleviation controller. The most promising design was selected for manufacturing. The finite element representation could be updated to conform to the measured eigenfrequencies, based on the dynamic identification of the model. Eventually, a wind tunnel test campaign was conducted in November 2018 and results have been examined in separate reports.

Response and Operational Modal Analysis from Wind Tunnel Test of the EOLO Flexible Aircraft

2021 ◽  
Author(s):  
David F. Castillo Zuñiga ◽  
Alain Giacobini Souza ◽  
Roberto G. da Silva ◽  
Luiz Carlos Sandoval Góes
Keyword(s):  
Wind Tunnel ◽  
Modal Analysis ◽  
Wind Tunnel Test ◽  
Operational Modal Analysis ◽  
Flexible Aircraft

DEVELOPMENT OF A RAPID PROTOTYPING METHODOLOGY FOR WIND TUNNEL TEST MODEL DESIGN

2019 ◽  
Author(s):  
Bruno Ricardo Massucatto Padilha ◽  
Guilherme Barufaldi ◽  
ROBERTO GIL ANNES DA SILVA
Keyword(s):  
Wind Tunnel ◽  
Rapid Prototyping ◽  
Wind Tunnel Test ◽  
Test Model ◽  
Model Design

Rancang Bangun Piranti Lunak Pengolah Data Pasca Pengujian Terowongan Angin Kecepatan Rendah Indonesia

2016 ◽  
Vol 7 (2) ◽  
pp. 131-138
Author(s):  
Ivransa Zuhdi Pane
Keyword(s):  
Wind Tunnel ◽  
Wind Tunnel Test ◽  
Test Results ◽  
Effective Solution ◽  
Post Processing ◽  
Prototype Development ◽  
Design Activities ◽  
Index Terms ◽  
Test Objects ◽  
Processing Requirement

Data post-processing plays important roles in a wind tunnel test, especially in supporting the validation of the test results and further data analysis related to the design activities of the test objects. One effective solution to carry out the data post-processing in an automated productive manner, and thus eliminate the cumbersome conventional manual way, is building a software which is able to execute calculations and have abilities in presenting and analyzing the data in accordance with the post-processing requirement. Through several prototype development cycles, this work attempts to engineer and realize such software to enhance the overall wind tunnel test activities. Index Terms—software engineering, wind tunnel test, data post-processing, prototype, pseudocode

Sign in / Sign up

Export Citation Format

Share Document