Effect of Nozzle Spacing on Flow Behavior in a Lean Direct Injection Combustor

A generic novel injector was designed for multi-Lean Direct Injection (M-LDI) combustors. One of the drawbacks of the conventional pressure swirl and prefilming type airblast atomizers is the difficulty of obtaining a uniform symmetric spray under all operating conditions. Micro-channels are needed inside the injector for uniformly distributing the fuel. The problem of non-uniformity is magnified in smaller sized injectors. The non-uniform liquid sheet causes local fuel rich/lean zones leading to higher NOx emissions. To overcome these problems, a novel fuel injector was designed to improve the fuel delivery to the injector by using a porous stainless steel material with 30 μm porosity. The porous tube also acts as a prefilming surface. Liquid and gaseous fuels can be injected through the injector. In the present study, gaseous fuel was injected to investigate injector fuel-air mixing performance. The gaseous fuel was injected through a porous tube between two radial-radial swirling air streams to facilitate fuel-air mixing. The advantage of this injector is that it increases the contact surface area between the fuel-air at the fuel injection point. The increased contact area enhances fuel-air mixing. Fuel-air mixing and combustion studies were carried out for both gaseous and liquid fuel. Flame visualization, and emissions measurements were carried out inside the exit of the combustor. The measurements were carried out at atmospheric conditions under fuel lean conditions. Natural gas was used as a fuel in these experiments. Fuel-air mixing studies were carried out at different equivalence ratios with and without confinement. The mass fraction distributions were measured at different downstream locations from the injector exit. Flame characterization was carried out by chemiluminescence at different equivalence ratios and inlet air temperatures. Symmetry of the flame, flame length and heat release distribution were analyzed from the flame images. The effects of inlet air temperature and combustion flame temperature on emissions was studied. Emissions were corrected to 15% O2 concentration. NOx emissions increase with inlet air temperature and flame temperature. Effect of flame temperature on NOx concentration is more significant than effect of inlet air temperature. Fuel-air mixing profile was used to obtain mass fraction Probability Density Function (pdf). The pdfs were used for simulations in Chemkin Pro. The measured emissions concentrations at the exit of the injector was compared with simulations. In Chemkin model, a network model with several PSRs (perfectly stirred reactor) were utilized, followed by a mixer and a PFR (plug flow reactor). The comparison between the simulations and the experimental results was investigated.

Download Full-text

Enabling the potential of hybrid electric propulsion through lean-burn-combustion turbofans

Journal of the Global Power and Propulsion Society ◽

10.33737/jgpps/140592 ◽

2021 ◽

Vol 5 ◽

pp. 164-176

Author(s):

Stavros Vouros ◽

Mavroudis Kavvalos ◽

Smruti Sahoo ◽

Konstantinos Kyprianidis

Keyword(s):

Electric Propulsion ◽

Direct Injection ◽

Operating Cost ◽

Pollutant Emissions ◽

Civil Aviation ◽

Lean Burn ◽

Lean Direct Injection ◽

Direct Operating Cost ◽

Hybrid Electric ◽

The Impact

Hybrid-electric propulsion has emerged as a promising technology to mitigate the adverse environmental impact of civil aviation. Boosting conventional gas turbines with electric power improves mission performance and operability. In this work the impact of electrification on pollutant emissions and direct operating cost of geared turbofan configurations is evaluated for an 150-passenger aircraft. A baseline two-and-a-half-shaft geared turbofan, representative of year 2035 entry-into-service technology, is employed. Parallel hybridization is implemented through coupling a battery-powered electric motor to the engine low-speed shaft. A multi-disciplinary design space exploration framework is employed comprising modelling methods for multi-point engine design, aircraft sizing, performance and pollutant emissions, mission and economic analysis. A probabilistic approach is developed considering uncertainties in the evaluation of direct operating cost. Sensitivities to electrical power system technology levels, as well as fuel price and emissions taxation are quantified at different time-frames. The benefits of lean direct injection are explored along short-, medium-, and long-range missions, demonstrating 32% NO<italic><sub>x</sub></italic> savings compared to traditional rich-burn, quick-mix, lean-burn technologies in short-range operations. The impact of electrification on the enhancement of lean direct injection benefits is investigated. For hybrid-electric powerplants, the take-off-to-cruise turbine entry temperature ratio is 2.5% lower than the baseline, extending the corresponding NO<italic><sub>x</sub></italic> reductions to the level of 46% in short-range missions. This work sheds light on the environmental and economic potential and limitations of a hybrid-electric propulsion concept towards a greener and sustainable civil aviation.

Download Full-text

Sector Tests of a Low NOx, Lean-Direct-Injection, Multipoint Integrated Module Combustor Concept

Volume 1: Turbo Expo 2002 ◽

10.1115/gt2002-30089 ◽

2002 ◽

Cited By ~ 34

Author(s):

Robert Tacina ◽

Changlie Wey ◽

Peter Laing ◽

Adel Mansour

Keyword(s):

Direct Injection ◽

Pressure Ratio ◽

Inlet Pressure ◽

Inlet Temperature ◽

Single Element ◽

Nox Emissions ◽

Fuel Injectors ◽

Lean Direct Injection ◽

Test Conditions ◽

Engine Cycle

Results of a low-NOx combustor test with a 15° sector are presented. A multipoint, lean-direct injection concept is used. The configuration tested has 36 fuel injectors and fuel-air mixers in place of a dual annular arrangement of two conventional fuel injectors. An integrated-module approach is used for the construction where chemically etched laminates that are diffusion bonded, combine the fuel injectors, air swirlers and fuel manifold into a single element. Test conditions include inlet temperatures up to 866K, and inlet pressures up to 4825 kPa. The fuel used was Jet A. A correlation is developed relating the NOx emissions to the inlet temperature, inlet pressure, and fuel-air ratio. Using a hypothetical 55:1 pressure-ratio engine, cycle NOx emissions are estimated to be less than 40% of the 1996 ICAO standard.

Download Full-text