Gas-induced forces generated on dense particle distributions in rarefied gas regimes

2022 ◽  
Author(s):  
Akhil Marayikkottu Vijayan ◽  
Deborah A. Levin
Keyword(s):  
Rarefied Gas ◽  
Dense Particle ◽  
Particle Distributions

NUMERICAL SIMULATION OF THE COMPACTION EFFECT DURING SHOCK WAVE € PARTICLE LAYER NUMERICAL SIMULATION OF THE COMPACTION EFFECT DURING SHOCK WAVE-PARTICLE LAYER INTERACTION

2020 ◽  
Author(s):  
YA. E. POROSHYNA ◽  
◽  
P. S. UTKIN ◽  
Keyword(s):  
Numerical Simulation ◽  
Shock Wave ◽  
Dust Explosion ◽  
Dense Particle ◽  
Layer Interaction ◽  
Particle Layer ◽  
Complex Process ◽  
Impermeable Wall

The problem of shock wave - dense particle layer interaction is a fundamental basis for the study of a more complex process of dust explosion or dust-layered detonation. The work presents results of numerical simulation of the experiment on interaction of an SW with particles layer deposited on the impermeable wall.

The use of particle monitoring in the performance optimisation of conventional clarification and filtration processes

1997 ◽  
Vol 36 (4) ◽  
pp. 191-198
Author(s):  
G. Standen ◽  
P. J. Insole ◽  
K. J. Shek ◽  
R. A. Irwin
Keyword(s):  
Activated Carbon ◽  
Water Supply ◽  
Laser Diffraction ◽  
Raw Water ◽  
Particle Distributions ◽  
Upper Limit ◽  
Start Up ◽  
On Line ◽  
Particulates Removal ◽  
Particle Monitoring

The application of laser diffraction particle monitoring to the performance optimisation of a pilot clarifier and full-scale rapid gravity filters (RGF), operating on water supply works in Hampshire, is described. Furthermore the dosing of powdered activated carbon (PAC) into the works' clarifiers has been evaluated in terms of RGF performance. A costly proposal to install a third filter medium was subsequently abandoned when it was found that particle numbers in the filtered water were consistently below 1×102/ml. Various combinations and doses of coagulants and flocculant aids, shown to give optimum particulates removal during intensive jar testing trials, were transferred to the pilot clarifier. Particle monitoring enabled a more accurate derivation of suitable blanket chemistry and optimum blanket heights than turbidity changes. Raw water turbidities were 10-15 NTU at start-up with corresponding counts beyond the upper limit of the particle monitor. An on-line dilution system was developed to overcome this problem. Latex bead (4.33 μm) and Lycopodium spore (4-5 μm) suspensions (about 1 × 109 particles) were injected into the pilot clarifier to assess the removal efficiency of Cryptosporidium-sized particles. Reductions of about 1.7 log and 2.6 log were achieved for the beads and spores, respectively. Particle distributions of various PAC's and a bentonite were obtained in order to assess their potential effects on the coagulation process during clarification. Bentonite was also beneficial as an on-line means of checking particle monitor response and calibration. The works' filters achieved 1.5 to 2.0 log removals of 2-5 μm particles without media addition or operational changes. Combined clarification and filtration gave better particulates removal than two-stage microfiltration.

Comparison of DSMC and CFD Models of Heat Transfer in a Rarefied Two-Dimensional Geometry

2018 ◽  
Author(s):  
Dilesh Maharjan ◽  
Mustafa Hadj-Nacer ◽  
Miles Greiner ◽  
Stefan K. Stefanov
Keyword(s):  
Heat Transfer ◽  
Rarefied Gas ◽  
Complex Geometry ◽  
Direct Simulation Monte Carlo ◽  
Accurate Method ◽  
Vacuum Drying ◽  
Helium Pressure ◽  
Two Dimensional ◽  
Dsmc Method ◽  
Cfd Simulations

During vacuum drying of used nuclear fuel (UNF) canisters, helium pressure is reduced to as low as 67 Pa to promote evaporation and removal of remaining water after draining process. At such low pressure, and considering the dimensions of the system, helium is mildly rarefied, which induces a thermal-resistance temperature-jump at gas–solid interfaces that contributes to the increase of cladding temperature. It is important to maintain the temperature of the cladding below roughly 400 °C to avoid radial hydride formation, which may cause cladding embrittlement during transportation and long-term storage. Direct Simulation Monte Carlo (DSMC) method is an accurate method to predict heat transfer and temperature under rarefied condition. However, it is not convenient for complex geometry like a UNF canister. Computational Fluid Dynamics (CFD) simulations are more convenient to apply but their accuracy for rarefied condition are not well established. This work seeks to validate the use of CFD simulations to model heat transfer through rarefied gas in simple two-dimensional geometry by comparing the results to the more accurate DSMC method. The geometry consists of a circular fuel rod centered inside a square cross-section enclosure filled with rarefied helium. The validated CFD model will be used later to accurately estimate the temperature of an UNF canister subjected to vacuum drying condition.

On the viscosity of rarefied gas suspensions containing nanoparticles

2003 ◽  
Vol 48 (10) ◽  
pp. 583-586 ◽  
Author(s):  
V. Ya. Rudyak ◽  
S. L. Krasnolutskii
Keyword(s):  
Rarefied Gas ◽  
Gas Suspensions

Investigation of the Squeeze Film Dynamics Underneath a Microstructure With Large Oscillation Amplitudes and Inertia Effects

2016 ◽  
Vol 138 (3) ◽  
Author(s):  
Nadim A. Diab ◽  
Issam A. Lakkis
Keyword(s):  
Rarefied Gas ◽  
Direct Simulation Monte Carlo ◽  
Squeeze Film ◽  
Dsmc Method ◽  
Inertia Effects ◽  
Flow Parameters ◽  
Fluid Behavior ◽  
Dimensionless Groups ◽  
Simulation Monte Carlo ◽  
The Impact

This paper presents direct simulation Monte Carlo (DSMC) numerical investigation of the dynamic behavior of a gas film in a microbeam. The microbeam undergoes large amplitude harmonic motion between its equilibrium position and the fixed substrate underneath. Unlike previous work in literature, the beam undergoes large displacements throughout the film gap thickness and the behavior of the gas film along with its impact on the moving microstructure (force exerted by gas on the beam's front and back faces) is discussed. Since the gas film thickness is of the order of few microns (i.e., 0.01 < Kn < 1), the rarefied gas exists in the noncontinuum regime and, as such, the DSMC method is used to simulate the fluid behavior. The impact of the squeeze film on the beam is investigated over a range of frequencies and velocity amplitudes, corresponding to ranges of dimensionless flow parameters such as the Reynolds, Strouhal, and Mach numbers on the gas film behavior. Moreover, the behavior of compressibility pressure waves as a function of these dimensionless groups is discussed for different simulation case studies.

Sign in / Sign up

Export Citation Format

Share Document